Eos Modular 4.0
Product Safety
Information &
User Instructions.
POWER DISTRIBUTION BLOCK
01] Safety Information
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
Do not install near any heat sources
such as radiators, heat registers, stoves,
or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the
polarised or grounding type plug.
A grounding type plug has two blades
and a third grounding prong. The wide
blade or the third prong is provided for
your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and at
the point where they exit from the
apparatus.
Only use attachments/accessories
specified by the manufacturer.*
Unplug this apparatus during lightning
storms or when unused for long periods
of time.
Refer all servicing to qualified service
personnel.
Servicing is required when the
power-supply cord or plug has been
damaged, liquid has been spilled or
objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
or has been dropped.
POWER SOURCES
Connect the apparatus to a power
supply only of the type described in the
operating instructions or marked on the
apparatus.
MAINS POWER CABLES
Disconnect the apparatus from the
mains supply via the mains plug. The
mains plug must be accessible at all
times.
*Atlas recommend Eos power cables for
optimum performance with this unit.
These or equivalent power cables can be
obtained from your retailer.
Warning: this appliance must be
earthed.
**Maximum supply from Eos
Modular is 10A in countries
where the power supply is 230v.
Internal fuse(s) are of 10A rating, this
value should NOT be exceeded.
In countries where the power supply is
115v, the fitted 10A fuse(s) may be
replaced with the supplied 15A fuses to
increase safe current operation to 15A.
Objects and liquid entry.
Do not let objects or liquids fall into the
apparatus, or expose the apparatus to
dripping or splashing.
Do not place a vessel containing liquid
on top of the apparatus.
No naked flame sources, such as lighted
candles, should be placed on the
apparatus.
The apparatus has been designed for
use in moderate and tropical climates.
Ensure adequate ventilation, do not
stack.
Read and
keep these
instructions
for your
safety and
protection.
continued overleaf...
02] Safety Instructions
Explanation of symbols used in this
manual or on the rear/ underside of the
apparatus:
This symbol is intended to alert the
user to the presence of un-insulated
dangerous voltages within the enclosure
of sufficient magnitude to cause electric
shock.
This symbol is intended to alert the user
to the presence of important operation,
maintenance and servicing information
in the instruction and service manuals.
For apparatus connected to the mains
electricity supply:
CAUTION
To r educe the r is k of electric shock
do not remove the cover.
There are no user serviceable parts
inside the products. Refer servicing to
qualified service personnel.
WAR NING
To r ed uce t he r is k of fir e or el ec tr ic shoc k
do not expose this apparatus to rain or
moisture.
This appliance should be connected to
a mains socket outlet with a protective
earth connection.
The external rear binding post provided
is for connection of Atlas Grounding
leads ONLY (see manufacturer’s web
site), no other apparatus or equipment
should be connected.
The external rear binding post is a
secondary ground connection and
should NEVER be used as a safety
ground connection.
FUSE REPLACEMENT
This appliance is fitted with a fused IEC
C14 socket. Should a fuse(s) need
replacing and you are competent to do
this proceed as follows:
If you are in doubt contact your
dealer or local electrical retailer.
a) Disconnect the unit from mains power.
Remove the IEC lead from the socket.
Pull out the fuse cover/carrier
(indicated) from the IEC socket.
b) Remove and dispose of the blown
fuse(s).
c) Fit a new 10 amp (max 15A for 115v
territories ONLY**) approved fuse (s)
into the carrier and push the carrier
back into the socket.
d) On some models there may be fuses on
both Live and Neutral conductors, it is
recommended that you replace both.
Always ensure the fuse cover is fitted.
If the fuse cover is missing do not use
the socket. Contact your local electrical
retailer to obtain a replacement fuse
cover.
Fuses are for fire protection and do not
protect against electric shock.
FUSE CARRIER
CE DECLARATION OF CONFORMITY
Atlas (Scotland) Ltd, Unit 5, Block 8,
Moorfield Industrial Estate, Kilmarnock,
Scotland declares under our sole responsibility that the named apparatus is in
conformance with 2006/95/EC (Low
Voltage Directive) as amended.
PRODUCT BRAND: Atlas
PRODUCT NAME(S): Eos Modular 4.0
PRODUCT TYPE: 6 way mains
conditioning/distribution unit
The products are CE marked Dec. 2016.
WAS TE ELEC TRIC AL AND ELECTRO NIC
EQUIPMENT (WEEE) DIRECTIVE
Waste Electrical and Electronic Equipment
Directive Directive 2002/96/EC of the
European Parliament and of the Council.
This symbol is shown on this product.
It indicates that the product should not be
disposed of with regular household waste,
but should be disposed of separately.
Electrical and electronic equipment can
contain materials that are hazardous to the
environment and human health and
therefore should be disposed of at a
designated waste facility or returned to
your retailer for the appropriate recycling to
take place (see www.atlascables.com for
further information).
If you wish to dispose of this product and
the product still functions, please consider
recycling/reusing it by donating it to a
charity shop, selling it or part-exchanging it
with your retailer.
Re-use is the best form of recycling.
atlascables.com
Atlas Cables
Unit 5, Block 8,
Moorfield Industrial Estate,
Troon Road, Kilmarnock,
Ayrshire, Scotland KA2 0BA
0800 023 7370 (UK only); or
+44 (0)1563 572666
Version 2, August 2017
Loading...