Atlas ATM1700T, ATM1700 User Manual

3505 HUTCHINSON ROAD
TM
U
L
C
US
R
AA
TTLLAASS
INDUSTRIAL FLAT PANEL PC MONITOR
QUICK INSTALLATION GUIDE - ATM1700/ATM1700T
Description:
The Atlas ATM1700/ATM1700T is a high performance 17" color TFT flat panel monitor specifically designed for harsh industrial environments including Class I & II, Division 2 Hazardous Locations. The ATM1700/ATM1700T accepts standard analog VGA input or digital DVI input, and can display all VESA video modes up to 1280 x 1024 at 75 Hz with 16 million colors. An optional 5-wire analog touch screen (ATM1700T) is available that offers both RS-232 and USB interface capability. The monitor is housed in a heavy duty steel chassis with a powder coated machined aluminum bezel. The monitor is certified to NEMA 4/4X/12 standards, is UL/CUL listed, meets CE
ATM1700/ATM1700T
NN
::
OOTTEE
EE T HE HARDWARE USERS GUIDE, ATM-17-USER,
S
INCLUDED ON THE SUPPLIED DOCUMENTATION & DRIVER CD FOR ADDITIONAL DETAILS. THE USERS GUIDE IS IN PDF FILE FORMAT AND REQUIRES DOWNLOADING ADOBES FREE ACROBAT READER TO OPEN AND VIEW.
requirements and is RoHS compliant. Panel mounting is simplified using convenient mounting clips instead of conventional studs. All monitors are shipped with a power input wiring receptacle, 6’ VGA cable, 6’ RS-232 cable (ATM1700T only), 2m USB Cable (ATM1700T only), mounting hardware, this Quick Installation Guide, and CD-ROM containing Hardware User’s Guide (ATM-17-USER) and touch screen driver software for Windows 98/NT/2000/XP/Vista.
w w w . a u t o m a t i o n d i r e c t . c o m
1. Verify Contents of the Box:
Atlas Flat Panel Monitor – ATM1700 or ATM1700T (The “T” at the end of the part number designates the touch screen option.)
• VGA video cable – 6’ length
• RS-232 Serial touch screen cable (ATM1700T only) – 6’ length
1 - 8 0 0 - 6 3 3 - 0 4 0 5
• USB touch screen cable (ATM1700T only) – 2m length
• Mounting clips and screws (qty of 14)
• USB retention bracket and mounting screw (ATM1700T only)
• Documentation and Driver CD
Contents:
AAttllaass
Monitor
Mounting Clips
(qty. 14)
(“T” ver. only)
Dimensions:
Packaging
Material
USB Cable
RS-232 Cable & hex spacers (“T” ver. only)
Documentation
& Driver CD
VGA Video
Cable
Agency Approvals:
Certifications & Standards
Name UL508 UL1604 CE
AAttllaass
Flat Panel Monit
E191072 E313546
or
1
EN 55022-1: Class A,
EN 61000-3-2: Class A,
EN 61000-3-3, EN 61000-6-2,
IEC 60950-1
2. Install Monitor through Enclosure Door or Wall
CUTOUT
CUT AWAY
VIEW
* NOTE: USE ONE OR THE OTHER, NOT BOTH.
TOUCH SCREEN
CABLES *
VIDEO CABLE *
D
ISPLAY POWER
WARNING
T
ouch Screen is still
a
ctive while display
p
ower is off
• Use dimensions as shown in the diagram below to provide a rectangular mounting cutout in an approved NEMA 4/12 enclosure’s door or wall.
• Mount the monitor through the enclosure cutout, install and tighten (14) mounting clips to a torque of 8.0 inch-pounds as shown in the diagram to the right.
Cutout Dimensions:
Mounting Clip Installation:
w w w . a u t o m a t i o n d i r e c t . c o m
WARNING: An operating temperature of 0 to 50 °C (32 to 122 °F) needs to be maintained for proper operation of the monitor.
3. Connect DVI or VGA Video Cable between Monitor & PC
Cable Connections:
WARNING: Damage can occur by applying excessive torque to the mounting clips.
• Connect the included 6’ VGA video cable from the video connector on the monitor to the video output connector on the host PC being used with the monitor or use a digital DVI-M cable (sold separately).
• If using a DVI-D cable, then special instructions apply when applying power; see warning to the right in regards to selecting the video input.
NN
::
OOTTEE
HE 17” MONITOR WILL PRODUCE THE BEST IMAGE QUALITY IF
1 - 8 0 0 - 6 3 3 - 0 4 0 5
T
THE PC IS SET FOR A 1280 X 1024 PIXELS @ EITHER 60, OR 75 HZ. VIDEO MODE.
4. Connect USB or Serial Cable between Monitor & PC
• Applies to ATM1700T touch screen version only.
• Use either the included 6’ RS-232 Serial touch screen cable or the 2m USB touch screen cable from the appropriate connector on the monitor to the appropriate connector on the host computer; do not connect both.
• If using the USB cable, secure the cable using the included USB retention bracket and screw; consult the Hardware User’s Guide, ATM-17-USER, on the supplied Documentation and Drive CD for details.
WARNING
To minimize the risk of potential safety problems, you should follow all applicable local and national codes that regulate the installation and operation of your equipment. These codes vary from area to area and it is your responsibility to determine which codes should be
followed, and to verify that the equipment, installation, and operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the failure to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or operation of this equipment, or if you need additional information, please call Technical Support at 770-844-4200.
This publication is based on information that was available at the time it was printed. At Automationdirect.com our products and services, so we reserve the right to make changes to the products and/or publications at any time without notice and without obligation. This publication may also discuss features that may not be available in certain revisions of the product.
®
we constantly strive to improve
2
Display Power
Button
Power
Indicator
DISPLAY POWER
WARNING
Touch Screen is still
active while display
power is off
MAIN MENU
BRIGHTNESS/CONTRAST
1280X1024 63.9KHZ/60HZ
COLOR POSITION SETUP EXIT
R G B
5. Connect Power to the Monitor
TOP VIEW
FRONT VIEW
A
DC P.N. ATM-AC-CON or
PHOENIX CONTACT P.N. 1777992
L
N
Plug Retention Screws
Power
Connection
L
abel
P
E
3
12
• Power source needs to be 100 - 240 VAC, 50/60 Hz, 욷30 Watts.
• See connection diagram below.
• Secure power connector screws to monitor.
• Power should not be applied until all cables are attached and the monitor is ready to operate.
WARNING: Damage can occur if power is not properly connected.
6. Apply Power to the Monitor & PC
• Press the DISPLAY POWER button on the rear of the monitor to wake the monitor up. Pressing the DISPLAY POWER button again turns off the backlight inverter and puts the monitor in a reduced power state but the touch screen remains active. It is important to note that this switch does not disconnect power from the monitor. Power is always supplied to the internal AC/DC power supply, which in turn continually supplies power to the internal monitor electronics and the optional touch screen controller.
Power Connections:
100 VAC - 240 VAC INPUT (1.0 Amps Min)
PIN No. Definition
1 AC Line Input
2 AC Neutral Return
3 Protective Earth Ground
LCD Power Button:
7. Install the Appropriate Touch Screen Driver
• Applies to ATM1700T touch screen version only.
• Insert the Documentation and Driver CD into the host PC’s CD drive.
• If the CD does not start automatically with the window shown below displayed, then go to Start > Run, browse to the CD’s “atlas.exe” file, open it, and click OK.
• From the Atlas screen, the user can view the Hardware User’s Guide for the monitor being used, and/or install the touch screen drivers for the particular PC operating system being used. Before installing the drivers, please read the Touch Screen Driver Documentation for operating system details.
• Reboot the PC and restart the monitor to activate the driver.
1 - 8 0 0 - 6 3 3 - 0 4 0 5
8. Verify Video and Touch Screen Functionality
• Verify the monitor’s video display by running a familiar program.
• If using the touch screen model (ATM1700T), use the touch screen to navigate by running a familiar program.
WARNING: The monitor does not automatically select a video input mode. The user must press the “UP (VGA/DVI)” button on the rear of the monitor to select either VGA or DVI input. If a “No Video” message appears on the screen, it is also suggested the user try using the “UP (VGA/DVI)” button to select the active video input.
NN
::
OOTTEE
ONCE YOU HAVE CONNECTED YOUR PC AND THE MONITOR,
SELECTED THE VIDEO SOURCE, AND POWERED BOTH UNITS, IT IS
SUGGESTED THAT THE OF THE MONITOR BE PRESSED TO MAXIMIZE THE VIDEO SETTINGS.
“SELECT (AUTO ADJ)” BUTTON ON THE REAR
OSD Settings Main Menu:
w w w . a u t o m a t i o n d i r e c t . c o m
9. Adjust the Monitor OSD Settings as Required
• Press the Select (Auto Adj) control button on the rear of the panel to initiate an automatic configuration of the screen.
• Although normally not needed, the control buttons on the rear of panel can be used to make other adjustments to the screen.
• Consult the Hardware User’s Guide, ATM-17-USER, on the supplied Documentation and Drive CD for detailed usage of the OSD settings.
10. Installation Complete
Additional Help and Support
• For product support, specifications, installation, and troubleshooting, a Hardware User’s Guide, ATM-17­USER, is included on the supplied Documentation and Driver CD, or downloadable from the Online Documentation area of the AutomationDirect Web site.
• For additional technical support and questions, call our Technical Support team @ 770-844-4200.
3
Accessories & Replacement Parts:
Part Number Description
ATM-CBL-VGA10
ATM-CBL-VGA25
ATM-CBL-VGA50
10 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
25 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
50 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
ATM-CBL-DV2M
ATM-CBL-DV3M
ATM-CBL-10
ATM-CBL-25
ATM-CBL-50
USB-CBL-AB3
USB-CBL-AB6
USB-CBL-AB10
USB-CBL-AB15
ATM-AC-CON
ATM-CLIP
ATM-CBL-VGA10
6 ft. (2 meter) DVI (type D) video cable. Connects M1700 and M1900 to a standard DVI-D port. DVI cables provide a higher bandwidth video interface than the VGA cables.
10 ft. (3 meter) DVI (type D) video cable. Connects M1700 and M1900 to a standard DVI-D port. DVI cables provide a higher bandwidth video interface than the VGA cables.
10 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
25 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
50 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
3-ft (0.9 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all USB devices.
6-ft (1.8 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all USB devices.
10-ft (3 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all USB devices.
15-ft (4.6 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all USB devices.
Replacement Power Wiring Connector for AC Powered Units.
Replacement flat panel mounting clip kit. Package of 16 clips and screws.
ATM-CBL-10
ATM-CBL-25
ATM-CBL-50
w w w . a u t o m a t i o n d i r e c t . c o m
USB-CBL-AB3
USB-CBL-AB6
1 - 8 0 0 - 6 3 3 - 0 4 0 5
ATM-CBL-VGA50
USB-CBL-AB10
ATM-CBL-VGA25
USB-CBL-AB15
ATM-AC-CON
ATM-CBL-DV2M
ATM-CLIP
Quick Installation Guide: ATM-17-QIG, Rev. B
ATM-CBL-DV3M
Copyright 2007, Automationdirect.com Incorporated/All Rights Reserved Worldwide
4
Loading...