Page 1
AA
TM
3
1
2
B
F
C
A
E
D
U
L
C
US
R
TTLLAASS
INDUSTRIAL FLAT PANEL PC MONITOR
QUICK INSTALLATION GUIDE
Atlas Industrial Monitor
NN
::
OOTTEE
SEE THE HARDWARE USER’S GUIDE, ATM-USER,
INCLUDED ON THE SUPPLIED DOCUMENTATION & DRIVER CD FOR
DDITIONAL DETAILS
A
REQUIRES DOWNLOADING
AND VIEW.
. THEUSER’S GU
ADOBE’S FREE ACROBAT READER TO OPEN
1. Verify Contents of the Box:
• Atlas Flat Panel Monitor – (A “T” at the end of the part number
designates the touch screen option.)
• VGA video cable – 10’ length
• RS-232 Serial touch screen cable (touch screen models only) – 10’ length
• USB touch screen cable (touch screen models only) – 10’ length
• Mounting clips and screws (qty of 14)
1 - 8 0 0 - 6 3 3 - 0 4 0 5
• USB retention bracket and mounting screw (touch screen models only)
• Optional power plug protective cover
• Documentation and Driver CD
• This Quick Installation Guide
IDE IS IN
ILE FORMAT AND
PDF F
3505 HUTCHINSON ROAD
CUMMING, GA 30040-5860, USA
Description:
The Atlas monitor is a high performance color TFT flat panel monitor
specifically designed for harsh industrial environments including Class
I Division 2, Class II Division 2 and Class III Hazardous Locations. The
Atlas monitor accepts standard analog VGA input or digital DVI input,
and can display all VESA video modes up to 1280 x 1024 at 75 Hz with
16 million colors. An optional 5-wire analog touch screen is available
that offers both RS-232 and USB interface capability. The monitor is
housed in a heavy duty steel chassis with a powder coated machined
aluminum bezel. The monitor is certified to NEMA 4/4X/12 standards,
is UL/CUL listed, meets CE requirements and is RoHS compliant.
Panel mounting is simplified using convenient mounting clips instead
of conventional studs. All monitors are shipped with a power input
wiring receptacle, 10’ VGA cable, 10’ RS-232 cable (touch panel
models only), 10’ USB Cable (touch panel models only), mounting
hardware, this Quick Installation Guide, and CD-ROM containing
Hardware User’s Guide (ATM-USER) and touch screen driver software
for Windows 98/NT/2000/XP/Vista/7.
Dimensions:
w w w . a u t o m a t i o n d i r e c t . c o m
Contents:
AAttllaass
Monitor
Mounting Clips
(qty. 14)
RS-232 Cable
& hex spacers
(“T” ver. only)
Documentation
& Driver CD
VGA Video
Cable
Packaging
Material
Quick
Installation
Guide
USB Cable
(“T” ver. only)
Model
ATM1500/ATM1500T
ATM1700/ATM1700T
ATM1900/ATM1900T
Agency Approvals:
Certifications & Standards
Name UL508
AAttllaass
Flat Panel Monitor
E157382 E200031
1
A B C D E F
12.80”
(325.1 mm)
14.48”
(367.8 mm)
15.70”
(398.8 mm)
12.12.01-2012
ANSI/ISA
15.80”
(401.3 mm)
17.14”
(435.4 mm)
18.66”
(474.0 mm)
EN 61000-3-2: Class A,
2.65”
(67.3 mm)
2.85”
(72.4 mm)
2.95”
(74.9 mm)
CE
EN 55022-1: Class A,
EN 61000-3-3,
EN 61000-6-2,
IEC 60950-1
3.95”
(100.3 mm)
5.00”
(127 mm)
6.00”
(152.4 mm)
1.17”
(29.8 mm)
1.32”
(33.5 mm)
1.50”
(38.1 mm)
2.40”
(61.0 mm)
2.60”
(66.0 mm)
2.70”
(68.6 mm)
Page 2
2. Install Monitor through Enclosure Door or Wall
CUTOUT
A
B
C
UT AWAY
V
IEW
MAXIMUM ALLOWABLE
PANEL THICKNESS
* NOTE: USE ONE OR THE
OTHER, NOT BOTH.
TOUCH SCREEN
CABLES *
VIDEO CABLE *
D
ISPLAY POWER
WARNING
T
ouch Screen is still
a
ctive while display
p
ower is off
• The monitor must be installed on a flat surface of a NEMA type 1, 4, 4X
or 12 enclosure.
• Use dimensions as shown in the diagram below to provide a
rectangular mounting cutout in an approved NEMA 4/12 enclosure’s
door or wall.
• Mount the monitor through the enclosure cutout, install and tighten (14)
mounting clips to a torque of 8.0 inch-pounds as shown in the diagram
to the right.
Cutout Dimensions:
Mounting Clip Installation:
Model
ATM1500/ATM1500T
ATM1700/ATM1700T
ATM1900/ATM1900T
A B
12.00”
304.8 mm)
(
13.70”
(348.0 mm)
4.90”
1
(378.5 mm)
15.00”
381.0 mm)
(
16.35”
(415.3 mm)
7.75”
1
(450.9 mm)
WARNING: An operating temperature of 0 to 50 °C (32 to 122 °F)
ambient termperature inside the enclosure needs to be maintained
for proper operation of the monitor.
Warning: Suitable for use in Class 1, Division 2 Groups A, B, C,
and D; Class 2 Division 2 Groups F and G, Class III hazardous
locations, or nonhazardous locations only.
3. Connect DVI or VGA Video Cable between Monitor & PC
• Connect the included 10’ VGA video cable from the video connector on
the monitor to the video output connector on the host PC being used
with the monitor or use a digital DVI cable (sold separately).
• If using a DVI cable, input selection must be changed to DVI by pushing
1 - 8 0 0 - 6 3 3 - 0 4 0 5
the UP button on the rear of the monitor.
NN
::
OOTTEE
THE 15” MONITOR WILL PRODUCE THE BEST IMAGE QUALITY IF
THE PC IS SET FOR A 1024 X 768 PIXELS @ EITHER 60, 70 OR 75 HZ.
VIDEO MODE.
w w w . a u t o m a t i o n d i r e c t . c o m
WARNING: Damage can occur by applying excessive torque to the
mounting clips.
Cable Connections:
NN
::
OOTTEE
THE 17” AND 19” MONITORS WILL PRODUCE THE BEST IMAGE
QUALITY IF THE
OR 75 HZ. VIDEO MODE.
PC IS SET FOR A 1280 X 1024 PIXELS @ EITHER 60,
4. Connect USB or Serial Cable between Monitor & PC
• Applies to touch screen version only.
• Use either the included 10’ RS-232 Serial touch screen cable or the 10’
USB touch screen cable from the appropriate connector on the monitor
to the appropriate connector on the host computer; do not connect
both.
• If using the USB cable, secure the cable using the included USB
retention bracket and screw; consult the Hardware User’s Guide,
ATM-USER, on the supplied Documentation and Driver CD for details.
NN
OOTTEE
OF THE USB RETENTION BRACKET IS REQUIRED FOR HAZARDOUS LOCA-
TIONS AND HIGHLY RECOMMENDED FOR NONHAZARDOUS LOCATIONS.
::
WHEN USING THE USB TOUCHSCREEN CONNECTION, THE USE
2
WARNING - EXPLOSION HAZARD - Do not connect or disconnect the
USB ports unless the power has been switched off or the area is
known to be non-hazardous.
AVERTISSEMENT - RISQUE D'EXPLOSION - Ne pas brancher ou débrancher
le ports USB á moins que l'alimentation á été coupée ou si la zone
n'est pas hazardeuse.
ADVERTENCIA - PELIGRO DE EXPLOSIÓN - No conecte o desconecte los
puertos USB a menos que la computadora se encuentre apagada o
el área se considere no peligrosa.
WARNUNG - EXPLOSIONSGEFAHR - USB-Ports nur anschließen oder
trennen, wenn keine spannung anliegt oder der Bereich nicht
explosiongefährdet ist.
NN
::
OOTTEE
TO PREVENT INADVERTANT DISCONNECTION OF VIDEO AND / OR
SERIAL TOUCHSCREEN CABLES ASSURE THAT THE THUMBSCREWS ARE
SUFFICIENTLY TIGHT.
Page 3
Display Power
Button
Power
Indicator
D
ISPLAY POWER
WARNING
Touch Screen is still
active while display
power is off
MAIN MENU
BRIGHTNESS/CONTRAST
1280X1024 63.9KHZ/60HZ
COLOR
POSITION
SETUP
EXIT
R G B
5. Connect Power to the Monitor
TOP VIEW
FRONT VIEW
A
DC P.N. ATM-AC-CON or
PHOENIX CONTACT P.N. 1777992
L N
Plug Retention Screws
Power
C
onnection
Label
PE
31 2
• Power source needs to be 100 - 240 VAC, 50/60 Hz.
• See power connection diagram to the right.
• Secure plug retention screws to monitor.
• Power should not be applied until all cables are attached and the
monitor is ready to operate.
Power Connections:
100 VAC - 240 VAC INPUT (1.0 Amps Min)
PIN No. Definition
1 AC Line Input
2 AC Neutral Return
rotective Earth Ground
3 P
RNING
WA
WARNING - EXPLOSION HAZARD - Do not disconnect equipment while
the circuit is live unless the area is known to be free of ignitable
concentrations.
: Damage can occur if power is not properly connected.
6. Apply Power to the Monitor & PC
• Press the DISPLAY POWER button on the rear of the monitor to wake the
monitor up. Pressing the DISPLAY POWER button again turns off the
backlight inverter and puts the monitor in a reduced power state but
the touch screen remains active. It is important to note that this switch
does not disconnect power from the monitor. Power is always supplied
to the internal AC/DC power supply, which in turn continually supplies
power to the internal monitor electronics and the optional touch screen
controller.
7. Install the Appropriate Touch Screen Driver
• The calibration of the touch screen occurs by a calibration utility that
installs as part of the touch screen driver installation process.
• Applies to touch screen version only.
• Insert the Documentation and Driver CD into the host PC’s CD drive.
• If the CD does not start automatically with the window shown below
displayed, then go to Start > Run, browse to the CD’s “atlas.exe” file,
open it, and click OK.
• From the Atlas screen, the user can view the Hardware User’s Guide for
the monitor being used, and/or install the touch screen drivers for the
particular PC operating system being used. Before installing the drivers,
please read the Touch Screen Driver Documentation for operating
system details.
• Reboot the PC and restart the monitor to activate the driver.
1 - 8 0 0 - 6 3 3 - 0 4 0 5
Warning - Explosion Hazard - Substition of any components may
impair suitability for Class 1, Division 2.
LCD Power Button:
Required Wire Specification
Wire Size
Wire Material and
Temperature
ightening Torque
T
8 - 12 AWG (0.8 - 3.3 mm
1
60 °C or 60 / 75 °C Copper
7.0 lb·in (0.79 Nm)
Panel Power Draw
ATM1500 (T)
ATM1700 (T)
ATM1900 (T)
25 W
30 W
35 W
2
)
w w w . a u t o m a t i o n d i r e c t . c o m
8. Verify Video and Touch Screen Functionality
• Verify the monitor’s video display by running a familiar program.
• If using the touch screen model, use the touch screen to navigate by
running a familiar program.
9. Adjust the Monitor OSD Settings as Required
• Press the Select (Auto Adj) control button on the rear of the panel to
initiate an automatic configuration of the screen.
• Although normally not needed, the control buttons on the rear of panel
can be used to make other adjustments to the screen.
• Consult the Hardware User’s Guide, ATM-USER, on the supplied
Documentation and Driver CD for detailed usage of the OSD settings.
10. Installation Complete
WARNING – Touch screen is still active while display power is off.
ATTENTION – L'écran tactile est toujours actif, méme quand l'afficheur n'est pas alimenté.
ADVERTENCIA – La pantalla táctil sigue activa aún cuando el display esté apagado.
WARNUNG – Touch screen ist immer noch aktiv, während die
anzeigefläche ausgeschaltet ist.
WARNING: The monitor does not automatically select a video input
mode. The user must press the “UP (VGA/DVI)” button on the rear
of the monitor to select either VGA or DVI input. If a “No Video”
message appears on the screen, it is also suggested the user try using
the “UP (VGA/DVI)” button to select the active video input.
NN
::
OOTTEE
ONCE YOU HAVE CONNECTED YOUR PC AND THE MONITOR,
SELECTED THE VIDEO SOURCE, AND POWERED BOTH UNITS, IT IS
SUGGESTED THAT THE “SELECT (AUTO ADJ)” BUTTON ON THE REAR
OF THE MONITOR BE PRESSED TO MAXIMIZE THE VIDEO SETTINGS.
OSD Settings Main Menu:
3
Page 4
Accessories & Replacement Parts:
Part Number Description
TM-CBL-VGA10
A
TM-CBL-VGA25
A
TM-CBL-VGA50
A
10 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
25 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
0 ft. 15-pin coaxial VGA cable. Connects any Atlas monitor to a standard VGA card.
5
ATM-CBL-DV2M
TM-CBL-DV3M
A
ATM-CBL-10
ATM-CBL-25
ATM-CBL-50
USB-CBL-AB3
USB-CBL-AB6
SB-CBL-AB10
U
SB-CBL-AB15
U
TM-AC-CON
A
ATM-CLIP
6 ft. (2 meter) DVI (type D) video cable. Connects ATM1700 and ATM1900 to a standard DVI-D
ort. DVI cables provide a higher bandwidth video interface than the VGA cables.
p
10 ft. (3 meter) DVI (type D) video cable. Connects ATM1700 and ATM1900 to a standard DVI-D
ort. DVI cables provide a higher bandwidth video interface than the VGA cables.
p
0 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
1
(touch screen models only)
5 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
2
(touch screen models only)
0 ft. serial communication cable. Connects Atlas monitor to std. 9-pin RS-232 port.
5
(touch screen models only)
3-ft (0.9 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all
SB devices. (touch screen models only)
U
6-ft (1.8 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all
SB devices. (touch screen models only)
U
10-ft (3 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all
USB devices. (touch screen models only)
15-ft (4.6 meter) Standard USB 2.0 cable with Standard-A plug to Standard-B plug. Suitable for all
SB devices. (touch screen models only)
U
Replacement Power Wiring Connector for AC Powered Units.
Replacement flat panel mounting clip kit. Package of 16 clips and screws.
ATM-CBL-10
ATM-CBL-50
USB-CBL-AB6
ATM-CBL-25
USB-CBL-AB3
w w w . a u t o m a t i o n d i r e c t . c o m
USB-CBL-AB10
ATM-CBL-VGA10
ATM-CBL-VGA25
1 - 8 0 0 - 6 3 3 - 0 4 0 5
ATM-CBL-VGA50 ATM-CBL-DV2M
ATM-CBL-DV3M
ATM-CLIP
Additional Help and Support
• For product support, specifications, installation, and
troubleshooting, a Hardware User’s Guide, ATMUSER, is included on the supplied Documentation
and Driver CD, or downloadable from the Online
Documentation area of the AutomationDirect Web site.
• For additional technical support and questions, call our Technical
Support team @ 770-844-4200.
USB-CBL-AB15 ATM-AC-CON
WARNING
To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the
installation and operation of your equipment. These codes vary from
area to area and it is your responsibility to determine which codes
should be followed, and to verify that the equipment, installation, and
operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the failure
to follow all applicable codes and standards. We do not guarantee the products described in this publication are suitable for your particular application, nor do we assume any responsibility for your product design,
installation, or operation.
If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call
Technical Support at 770-844-4200.
This publication is based on information that was available at the time
it was printed. At Automationdirect.com®we constantly strive to
improve our products and services, so we reserve the right to make
changes to the products and/or publications at any time without notice
and without obligation. This publication may also discuss features that
may not be available in certain revisions of the product.
Copyright 2007-2014, Automationdirect.com Incorporated/All Rights Reserved Worldwide
4
Loading...