The Atlantis Land logo is a registered trademark of Atlantis Land SpA. All other names mentioned
mat be trademarks or registered trademarks of their respective owners. Subject to change without
notice. No liability for technical errors and/or omissions.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Important Note
The antenna(s) used for this equipment must be installed to provide a separation distance of at least 30
cm from all persons.
FCC Warning
This equipment has been tested and found to comply with the regulations for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this user’s guide, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at his own expense.
A02-RAV211 VoIP ADSL Modem/Router provides a high-speed Ethernet port for high-speed Internet
browsing. It can support downstream transmission rates of up to 8Mbps and upstream transmission
rates of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt
(G.992.1); G.lite (G992.2); G.hs (G994.1)).
The product supports PPPoA (RFC 2364 – PPP (Point-to-Point Protocol) over ATM Adaptation Layer
5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA
(RFC1577) to establish a connection with ISP. The product also supports VC-based and LLC-based
multiplexing.
It is the perfect solution to connect a small group of PCs to a high-speed broadband Internet
connection. Multi-users can have high-speed Internet access simultaneously.
This product also serves as an Internet firewall, protecting your network from being accessed by
outside users. Not only provide the natural firewall function (Network Address Translation, NAT), it
also provides rich firewall features to secure user’s network. All incoming data packets are monitored
and filtered. Besides, it can also be configured to block internal users from accessing to the Internet.
The product provides two levels of security support. First, it masks LAN users’ IP addresses which
are invisible to outside users on the Internet, making it much more difficult for a hacker to target a
machine on your network. Secondly, it can block and redirect certain ports to limit the services that
outside users can access. For example, to ensure that games and other Internet applications will run
properly, user can open some specific ports for outside users to access internal services in network.
Integrated DHCP (Dynamic Host Control Protocol) services, client and server, allow multiple users to
get their IP addresses automatically on boot up from the product. Simply set local machines as a
DHCP client to accept a dynamically assigned IP address from DHCP server and reboot. Each time
local machine is powered up; the router will recognize it and assign an IP address to instantly connect
it to the LAN.
For advanced users, Virtual Service function allows the product to provide limited visibility to local
machines with specific services for outside users. An ISP (Internet Service Providers) provided IP
address can be set to the product and then specific services can be rerouted to specific computers on
the local network. For instance, a dedicated web server can be connected to the Internet via the
product and then incoming requests for HTML that are received by the product can be rerouted to the
1
VoIP ROUTER ADSL
dedicated local web server, even though the server now has a different IP address. In this example, the
product is on the Internet and vulnerable to attacks, but the server is protected.
Virtual Server can also be used to re-task services to multiple servers. For instance, the product can be
set to allow separated FTP, Web, and Multiplayer game servers to share the same Internet-visible IP
address while still protecting the servers and LAN users from hackers.
A02-RAV211 serves as a Public Switched Telephone Network (PSTN) handset-to-Ethernet adaptor
that enables traditional telephone devices to operate as Internet Protocol (IP) devices. It is the interface
between the PSTN world and the IP world acting as a residential gateway, eventually providing
Internet Telephony capability. Cost savings and ease of developing and integrating new services
motivate most of the interest in Internet telephony. Internet telephony integrates a variety of services
provided by the current Internet and the PSTN infrastructure. Internet telephony employs a variety of
protocols, including Real-time Transport Protocol (RTP) for transport of multimedia data and Session
Initiation Protocol (SIP) or H.323 for call signaling and control.
A02-RAV211 extracts the maximum benefit from Voice over IP (VoIP) and Fax over IP (FoIP)
technologies. It interfaces analog telephones with IP-based telephony networks. The integration of
VoIP technology and ADSL Modem/Router is undoubtedly the most economic and practical solution
to modern society.
1.2 Package Contents
• VoIP Router ADSL
• One CD-ROM containing the online manual
• One Quick Start Guide
• One RJ-11 ADSL/telephone cable
• One CAT-5 LAN cable
• One AC-DC power adapter (12VDC, 1A)
If any of the above items are missing, please contact your reseller.
1.3 VoIP Router ADSL Features
Atlantis Land A02-RAV211 ADSL Modem/Router provides the following features:
ADSL Multi-Mode Standard: Supports downstream transmission rates of up to 8Mbps and upstream
transmission rates of up to 1024Kbps. It is compliant with Multi-Mode standard (ANSI T1.413, Issue
2; G.dmt (G.992.1); G.lite (G992.2); G.hs (G994.1)).
Multi-Protocol to Establish A Connection: Supports PPPoA (RFC 2364 - PPP over ATM
Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC
2516) and IPoA (RFC1577) to establish a connection with ISP. The product also supports VC-based
and LLC-based multiplexing.
Quick Installation Wizard: Supports a WEB GUI page to install this device quickly. With this
wizard, an end user can enter the information easily which they from the ISP, then surf the Internet
immediately.
2
VoIP ROUTER ADSL
Universal Plug and Play (UPnP) and UPnP NAT Traversal: This protocol is used to enable simple
and robust connectivity among stand-alone devices and PCs from many different vendors. It makes
network simple and affordable for users. UPnP architecture leverages TCP/IP and the Web to enable
seamless proximity networking in addition to control and data transfer among networked devices.
With this feature enabled, users can now connect to Net meeting or MSN Messenger seamlessly.
Network Address Translation (NAT): Allows multi-users to access outside resource such as Internet
simultaneously with one IP address/one Internet access account. Besides, many application layer
gateway (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Ping and others.
Domain Name System (DNS) relay: Provides an easy way to map the domain name (a friendly name
for user such as www.yahoo.com) and IP address. When local machine sets its DNS server with this
router’s IP address. Then every DNS conversion request packet from the PC to this router will be
forwarded to the real DNS in outside network. After the router gets the reply, then forwards it back to
the PC.
Dynamic Domain Name System (DDNS): The Dynamic DNS service allows you to alias a dynamic
IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use
the service, you must first apply an account from this free Web server http://www.dyndns.org/. There
are more than 5 DDNS servers supported.
PPP over Ethernet (PPPoE): Provides embedded PPPoE client function to establish a connection.
Users can get greater access speed without changing the operation concept, sharing the same ISP
account and paying for one access account. No PPPoE client software is required for local computer.
The Automatic Reconnect and Disconnect Timeout (Idle Timer) functions are provided, too.
Virtual Server: User can specify some services to be visible from outside users. The router can detect
incoming service request and forward it to the specific local computer to handle it. For example, user
can assign a PC in LAN acting as WEB server inside and expose it to the outside network. Outside
user can browse inside web server directly while it is protected by NAT. A DMZ host setting is also
provided to a local computer exposed to the outside network, Internet.
Firewall: Supports SOHO firewall with NAT technology. Automatically detects and blocks the Denial
of Service (DoS) attack. Packet filtering is also supported. The hacker’s attack will be recorded
associated with timestamp in the security logging area. More firewall features will be added
continually, please visit our web site to download latest firmware.
Dynamic Host Control Protocol (DHCP) client and server: In the WAN site, the DHCP client can
get an IP address from the Internet Server Provider (ISP) automatically. In the LAN site, the DHCP
server can allocate multiple clients IP addresses and distribute them including IP address, subnet mask
as well as DNS IP address to local computers. It provides an easy way to manage the local IP network.
Rich Packet Filtering: Not only filter the packet based on IP address, but also based on Port numbers
and MAC address. It will increase the performance in LAN and WAN, also provide a higher-level
security control
SNTP: An easy way to get the network real time information from an SNTP server.
Web based GUI: Supports web based GUI for configuration and management. It is user-friendly and
comes with on-line help. It also supports remote management capability for remote users to configure
and manage this product.
3
VoIP ROUTER ADSL
1.4 VoIP Router ADSL Application
4
VoIP ROUTER ADSL
Chapter 2
Using VoIP Router ADSL
2.1 Cautions for using the VoIP Router ADSL
Do not place the ADSL VoIP Router under high humidity and high temperature.
Do not use the same power source for ADSL VoIP Router with other equipment.
Do not open or repair the case yourself. If the ADSL VoIP Router is too hot, turn off
the power immediately and have a qualified serviceman repair it.
Place the ADSL VoIP Router on a stable surface.
Only use the power adapter that comes with the package.
Do NOT upgrade firmware on any Atlantis Land product over a VoIP connection.
Failure of the device may result. Use only hard-wired network connections.
2.2 The Front LEDs
LED Meaning
PWR
SYS
Phone1
LAN
ADSL
Lit green when power adapter is connected.
When flash, it indicates that the device is working properly.
Lit green when the phone is off hook.
Lit green when the LAN link is connected.
When lit, it indicates that the ADSL (Line) port is connected to
the DSLAM and working properly.
2.3 The Rear Ports
5
VoIP ROUTER ADSL
PORT Meaning
Power Switch
Power Jack
Reset
VoIP
LAN
(RJ-45 connector)
A Power ON/OFF switch
Connect the supplied power adapter to this
jack.
Press it to restore the factory default setting
back.
Connect the RJ-11 cable to this port when
connecting to the phone set.
Connect the supplied Ethernet cable to this port
when connecting to a NIC (Network Interface
card) in PC.
Connect an UTP Ethernet cable to this port
when connecting to a LAN such as an office or
home network.
2.4 Cabling
The most common problem is bad cabling or ADSL line. Make sure that all connected devices are
turned on. On the front of the product is a bank of LEDs. As a first check, verify that the LAN Link
and ADSL line LEDs are lit and SYS is blanking. If they are not, verify that you are using the proper
cables.
6
VoIP ROUTER ADSL
Chapter 3
Configuration
The ADSL VoIP Router can be configured with your Web browser. The web browser is included
as a standard application in the following operation systems, UNIX, Linux, Mac OS, Windows
95/98/NT/2000/Me, and etc. The product provides a very easy and user-friendly interface for
configuration.
3.1 Before Configuration
This section describes the configuration required by LAN-attached PCs that communicate with the
ADSL VoIP Router, either to configure the device or for network access. These PCs must have an
Ethernet interface (or VoIP adapter) installed properly, be connected to the ADSL VoIP Router
either directly or through an external repeater hub, and have TCP/IP installed and configured to
obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet of
the ADSL Firewall Router. The default IP address of the ADSL VoIP Router is 192.168.1.254 and
subnet mask is 255.255.255.0. The best and easy way is to configure the PC to get an IP address
from the ADSL VoIP Router. Also make sure you have UNINSTALLED any kind of software
firewall that can cause problems while accessing the 192.168.1.254 IP address of the router.
Please follow the steps below for PC’s network environment installation. First of all, please check
your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be
installed. If not, please refer to MS Windows related manuals.
Any TCP/IP capable workstation can be used to communicate with or through
the ADSL VoIP Router. To configure other types of workstations, please
consult the manufacturer’s documentation.
3.2 Connecting the VoIP Router ADSL
• Connect the Router to a LAN (Local Area Network) and the ADSL/telephone network.
• Power on the device
• Make sure the PWR (SYS LED is blinking) is lit steady & LAN LED is lit.
• Before taking the next step, make sure you have uninstalled any software firewall.
7
VoIP ROUTER ADSL
3.3 Configuring PC in Windows
For Windows 95/98/ME
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network
and choose the Configuration tab.
2. Select TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card
(NIC) in your PC.
3. Click Properties.
4. Select the IP Address tab. In this page, click the Obtain an IP address automatically
radio button.
8
VoIP ROUTER ADSL
5. Then select the DNS Configuration tab.
6. Select the Disable DNS radio button and click “OK” to finish the configuration.
9
VoIP ROUTER ADSL
For Windows NT4.0
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network
and choose the Protocols tab.
2. Select TCP/IP Protocol and click Properties.
3. Select the Obtain an IP address from a DHCP server radio button and click “OK”.
10
VoIP ROUTER ADSL
For Windows 2000
1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network
and Dial-up Connections.
2. Double-click LAN Area Connection.
3. In the LAN Area Connection Status window, click Properties.
11
VoIP ROUTER ADSL
4. Select Internet Protocol (TCP/IP) and click Properties.
5. Select the Obtain an IP address automatically and the Obtain DNS server address
automatically radio buttons.
6. Click “OK” to finish the configuration.
12
VoIP ROUTER ADSL
For Windows XP
1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on
Network Connections.
2. Double-click Local Area Connection
3. In the LAN Area Connection Status window, click Properties.
13
VoIP ROUTER ADSL
4. Select Internet Protocol (TCP/IP) and click Properties.
5. Select the Obtain an IP address automatically and the Obtain DNS server address
automatically radio buttons
6. Click “OK” to finish the configuration.
14
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.