Atlantis AUW-701, AUW-5600, AUW-555, AUW-525C User Manual

User Manual

for

AUW-525C • AUW-555 • AUW-701 • AUW-5600

Introduction

Thank you for your purchase of the Atlantis Underwater Camera System. The Atlantis™, a high-resolution video camera and monitor system, offers multi-purpose applications in aquatic environments.

The Atlantis™ may be used for: sport fishing, search and rescue, treasure hunting, marine research or for recreational viewing of underwater activities. The Atlantis™, assisted by lighting, will help you see elusive underwater objects and find what you desire in any body of water.

You can search http://www.atlantiscamera.com for all your underwater camera needs: support, accessories, orders, information, testimonials, and tips on our Atlantis Cameras.

STOP

1. Make sure not to reverse the polarity. It may cause permanent damage to both monitor and camera. The red power cable and black ground cable should connect to red and black terminal of battery respectively.

2. Please make sure to turn off the monitor and disconnect power cable from the battery after use. Also, wipe off any moisture at both terminals on the battery to prevent from corrosion. This will ensure a clean contact between cables and terminals for future use.

3. Please remember to recharge the battery after each use until the red light comes on. You need to leave battery connected to the charger overnight. Keep battery away from the reach of children.

4. In clear water you should be able to view most objects in regular daylight. However, as your camera goes deeper underwater, there will be less light available and the camera’s light sources will be needed to view objects clearly.

In some conditions of highly dirty or milky water, it may be impossible to view any object clearly, even with lighting. This is simply because there are too many obstructions in the camera’s sight, and is not a malfunction of the camera.

Features

Camera: The Atlantis comes with a high-resolution camera

with a 92 degree viewing angle. The camera is housed in molded iron casting (aluminum for AUW-555), protecting it from water pressure and strikes from rocks or hard objects underwater. The camera also has attachable weights to stabilize and set the angle at which you want to view the

water. You can attach a fin to the camera to allow it to point in the direction of the boat. Our cables, up to 200’, are made of steel mesh and are durable in the water. The camera also is equipped with powerful infrared and colored LED lights that allow the camera to see in dark areas.

een Screen Monitor: This monitor has special green

phosphorous tubes that allow the monitor to be viewed with

significantly less glare than traditional black and white moni-

tors. The technology is used to provide the best viewing

ability in sunny conditions. We also conduct a G-5 force

vibration test on all monitors in the factory to ensure its sta-

bility. The monitor also allows connections for up to two cameras, and has an RCA video out for recording to a VCR or camcorder. You will also see a small square in the back of the monitor that is a mirror image switch. This monitor is designed to allow water to run off with a special coating we apply to the monitor. However, it is not waterproof because the monitors need vents to allow condensation to be released. In warm weather, if the monitor were sealed, the condensation would short-circuit the monitors, making it irreparable. Don’t let the monitor sit in water; use the mounting bracket or the case to protect it.

gh Impact carrying case: The Panning Atlantis Camera

is packaged in a water and air tight high impact resistant

case. Two springs loaded buttons lock the case, simply

push in the button and lift the lock down tabs to open. We

have dye cut foam inside the case to keep the components

from moving around in transportation. The case also has

slots for locks, and in the event that you drop the unit in the water, the case will float. This case provides maximum protection for your investment and it is recommended to only use this case when using your Atlantis™ system.

Table of Contents

Introduction / Precautions…………………………………..

Features…………………………………..…..…..…..

Setting Up / Using Atlantis

List of components………………………………….

Charging battery…………………………….............

Preparing for action………………………………....

Additional Functions

Recording…………………………………………... Replacing or changing fin………………………….. Adjusting viewing angle …………………………... Mounting the monitor………………………………………

Panning Camera

Features……………………………………..............

Operating the camera……………………………….

Color Camera

Features……………………………………….........

Parts………………………………………………... Connection Diagram………………………………..

01 02

04 05 05

07 07 07 08

08 09

09 10 11

FAQ………………………………………………………... Troubleshooting……………………………………………. Care & Maintenance……………………………………….. Warranty……………………………………………………

Specifications................................................................

12 14 15 15 17

1.Setting Up/Using Atlantis™

List of components

Make sure all parts and accessories are included.

___ 1. (1) 5.5” Green tube monitor

(7” Monitor for AUW-701 Color Monitor for AUW-5600)

___ 2. (1) Camera with 125’ cable

(200’ for AUW-701 Color Camera for AUW-5600

Panning Camera for AUW-555) ___ 3. (1) Battery, power cord with fuse ___ 4. (1) Battery charger ___ 5. (1) Boat mounting kit ___ 6. (1) Cigarette Adapter ___ 7. (1) Cable winder ___ 8. (1) Sunshade ___ 9. (1) Carrying case

Charging the Battery

1. Battery must be charged after each use and it is recommended that you charge your battery before you use it the first time.

2. Connect alligator clip to battery

Red: Power source link to red (+) terminal on the battery

Black: Ground link to black (-) terminal on the battery

3. Plug power adapter into 110V AC outlet.

4. Battery and Charger: We use the Rocket 12 volt Gel Cell batteries with our units which are known for their quality. Our battery charger has a red light indicator on it. When the battery is charging, there will be no light. When the battery is finished charging, the red light will turn on.

5. Unplug the adapter then remove alligator clips from battery.

Preparing for Action

1. Lift the monitor from the case.

2. Connect the battery to the wire according to the corresponding colors. You can also use the cigarette adapter to plug into your boat’s cigarette lighter and connect it to the monitor for power.

3. Connect the wire to the back of the monitor on the right.

4. Connect the camera cable to the back of the monitor in slot C1.

5. Turn on the power to the monitor.

6. Pull out the camera from the case and peel off the lens protector. (Blue vinyl) * Now you should be able to see an image on the monitor. If there is a problem, refer to the troubleshooting section of this manual.

Monitor AUM-701

+ 14 hidden pages