Page 1
Size of Mattress and Foundation
The length and width of the upper and lower bunk mattress and foundation are as follows :
Width
37 ½”- 38 ½”
52”- 53”
Thickness
9 ½” max
9 ½” max
Twin
Full
LengthSize
74”- 75”
74”- 75”
You must use only this size mattress.
Ensure thickness of upper and lower mattress and foundation combined does not exceed 9 ½”
and that the mattress is at least 5” below upper edge of guardrails.
This Bunk Bed uses a slat kit for mattress foundation.
Replacement Parts
Replacement parts, including additional guardrails, may be obtained from any
Atlantic Furniture dealer
SAFETY WARNINGS
! !
( 1 )
Follow the information on the warnings appearing on the upper bunk end structure
and on the carton. Do not remove warning label from bed.
( 2 )
( 3 )
( 4 )
( 5 )
( 6 )
( 7 )
( 8 )
( 9 )
(10)
(11)
(12)
(13)
Always use the recommended size mattresses or mattress support, or both,
to help prevent the likehood of entrapment or falls.
Surface of mattress must be at least 5 in. (127mm) below the upper edge of guardrails.
Do not allow children under 6 years of age to use the upper bunk.
Periodically check and ensure that the guardrail, ladder, and other component are
in their proper position, free from damage, and that all connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Always use ladder for entering or leaving upper bunk.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed
next to the wall, the guardrail that runs the full length of the bed should be placed against
the wall to prevent entrapment between the bed and the wall.
The use of water or sleep flotation mattresses is prohibited.
STRANGULATION HAZARD : Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts
and jump ropes.
Keep these instructions for future reference.
BUNK SAFETY WARNING
Page 1 of 8
Page 2
READY
NANTUCKET BUNK BED
ASSEMBLY INSTRUCTIONS
(TWIN - TWIN) (TWIN - FULL) (FULL - FULL)
Thank you for choosing Atlantic’s Bunk Bed.
This practical design offers the utmost in versatility.
Before assembling your Nantucket bunk bed, please read through these
instructions carefully. Familiarize yourself with the different parts.
Please note that you will require a Phillips head screwdriver and an Allen wrench.
ATTENTION! If you receive a damaged or defective item,
please contact Atlantic Furniture at service@atlanticfurniture.com 1-800-955-3726 / M-F 9:00-5:00 EST
Adult Assembly
Allen wrench
Customer Supplied
TWIN OVER FULL SHOWN
Phillips head
screwdriver
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
TWIN / TWIN FULL / FULL
HARDWARE
NOTE: WE INCLUDE SPARE HARDWARE IN CASE THE ALLEN WRENCH, JCB, BARREL NUT, WOOD SCREW OR WOOD BUTTON ARE DAMAGED DURING ASSEMBLY.
JCB M6 X 3 ½”(90mm) - 16 pcs
A
Spare - 2 pcs
1 ” Wood Screw - 4 pcs
E
D
Spare - 2 pcs
JCB M6 X 2”(50mm) - 4 pcs
B
Barrel Nut - 20 pcs
C
NANTUCKET BUNK BED
Spare - 2 pcs
Spare - 2 pcs
Metal Pins - 4 pcs
E
E
E
Wood Button - 8 pcs
F
Allen wrench - 1 pc
G
E
Spare - 1 pc
Spare - 1 pc
Page 2 of 8
Page 3
PARTS LIST
07
03
08
02
06
08
05
TWIN OVER FULL SHOWN
04
09
06
07
02
08
10
03
01
01
HARDWARE
02
UPPER PANEL
03
LOWER PANEL
04
FULL GUARD RAIL
05
3/4 GUARD RAIL
06
LEFT END CAPS
07
RIGHT END CAPS
08
LONG RAIL
08
1 BOX
1 BOX
1 BOX
09
TWIN SLAT KIT
OR
FULL UPPER BUNK SLAT KIT
10
FULL LOWER BUNK SLAT KIT
OR
TWIN LOWER BUNK SLAT KIT
NANTUCKET BUNK BED
1 BOX
1 BOX
1 BOX
1 BOX
Page 3 of 8
Page 4
STEP 1
02
Attach the long rails (08) to the upper panels (02), using JCB M6 X 3 ½” (A), and barrel nut (C).
Tighten with the Allen wrench (G).
A
A
Adult Assembly
STEP 2
C
08
C
08
C
A
02
A
If the bunk bed will be placed next to a wall, the guard rail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and the wall.
JCB M6 X 3 ½”
C
Barrel Nut
G
Allen wrench
06
B
C
NANTUCKET BUNK BED
B
07
C
04
05
C
Note : Screw holes on end caps
go on inside of guard rails.
C
B
06
07
Attach the full guard rail (04) to the end caps (06)(07), using JCB M6 X 2” (B),
and barrel nut (C). Tighten with the Allen wrench (G).
Repeat for 3/4 guard rail (05).
Adult Assembly
B
JCB M6 X 2 ”
C
B
Barrel Nut
G
Allen wrench
Page 4 of 8
Page 5
STEP 3
Lay the twin slat kit (09) onto the bed. Fix in place using wood screws provided in the slat kit box.
FOR SLAT KIT ASSEMBLY follow assembly instructions included with slat kit.
Adult Assembly
09
Customer Supplied
Phillips head
screwdriver
Twin size shown
Full Upper panel uses Full upper slat kit
STEP 4
3/4 GUARD RAIL
Install the full and 3/4 guard rail assemblies onto the long rails, and fix in place using wood
screws (D). Tighten with the Phillips head screwdriver.(Customer Supplied)
D
D
FULL GUARD RAIL
ASSEMBLY
Adult Assembly
D
1 “ Wood Screw
Customer Supplied
GUARDRAIL CAN BE SET UP AT EITHER
END OF THE BUNK BED
NANTUCKET BUNK BED
D
Phillips head
screwdriver
Page 5 of 8
Page 6
STEP 5
Attach the long rails (08) to the lower panel (03), using JCB M6 X 3 ½” (A), and barrel nut (C).
Tighten with the Allen wrench (G).
03
A
JCB M6 X 3 ½”
A
Adult Assembly
STEP 6
C
08
C
C
Barrel Nut
03
08
G
A
C
Allen wrench
A
Lay the slat kit with center support (10) onto the bed, and fix in place using wood screws
provided in the slat kit box. FOR SLAT KIT ASSEMBLY follow assembly instuctions included
with slat kit.
Full size shown
Twin lower panel uses Twin slat kit
NANTUCKET BUNK BED
10
Adult Assembly
Customer Supplied
Phillips head
screwdriver
Page 6 of 8
Page 7
STEP 7
E
Insert metal pins (E) into the holes in top of the lower panels. Lift the upper panels onto the
lower panels as shown, and fit the metal pins into the holes in the bottom of the upper panel legs.
TWIN-FULL
!
CAUTION
This step requires
This step requires
two strong people.
two strong people.
STEP 8
E
TWIN-TWIN
E
FULL-FULL
Cover holes with wood buttons (F)(Twin Full, Full Full ).
Adult Assembly
E
Metal Pins
Adult Assembly
TWIN OVER FULL SHOWN
and that all parts are secure before use and periodically check that all screws are tight to ensure lasting Safety.
NANTUCKET BUNK BED
F
F
Wood Button
F
Customer Supplied
F
Phillips head
screwdriver
Lastly, install Ladder.
FOR LADDER ASSEMBLY, PLEASE
FOLLOW ASSEMBLY INSTRUCTIONS
INCLUDED WITH YOUR LADDER.
Congratulations !
Your Nantucket bunk bed is now ready for use.
We recommend that you double check that all screws are tight,
Page 7 of 8
Page 8
CONVERSION TO 2 TWIN OR 2 FULL BEDS.
STEP 9
Disassemble upper bunk by removing guard rails. Also remove metal pin from lower bunk.
Metal Pin
UPPER BUNK
LOWER BUNK
Disassemble upper bunk by removing upper panel (02) and lower bunk by removing lower panel(03).
Exchange upper panel to the lower panel position and Install hardware tighten with Allen wrench.
02
03
STEP 10
Use Wood button (F)
to cover holes as shown.
UPPER BUNK
F
F
F
F
TWO TWIN BEDS
F
F
LOWER BUNK
F
F
F
F
F
F
NANTUCKET BUNK BED
TWO FULL BEDS
Page 8 of 8
Loading...