Atlantic 567200CASTORS Installation and Operation Guide

TATOU DIGITAL

PANNEAU RAYONNANT VERSIONS HORIZONTALES ET VERTICALES

Radiant panel heater - Horizontal and vertical
Warmtestraalradiator - Horizontale en verticale modellen
Emisor radiante - Versiones horizontales y verticales
Emissor radiante - Versões horizontais e verticais
Promiennik elektryczny - wersja POZIOMA i PIONOWA

F

SP

NL

PL

GB

P

RU

NOTICE D’UTILISATION ET D’INSTALLATION

Installation and operating manual - Gebruiks- en installatiehandleiding - Manual de utilización e instalación - Manual do Usuario
e da Instalação - Instrukcja obsługi i monta

ż

u -

GUIDE À CONSERVER
PAR L’UTILISATEUR

Manual must be kept by end user
Gids te bewaren door de gebruiker
Guía que deberá ser conservada por el usuario
Guia a conservar pelo usuario

Contents

Warning...........................................................................................................................................28

Installation

Preparing the installation of the device........................................................................................29

Unlocking the device’s hanging frame...........................................................................................30

Fixing the hanging frame to the wall.............................................................................................30

Connecting the device......................................................................................................................31

Locking the device on the hanging frame....................................................................................32

Operation.......................................................................................................................................33

Use

Turning on your device ....................................................................................................................34

Putting your device in standby mode ..........................................................................................34

Choosing your heating mode ........................................................................................................35

Heating your room: how to use Comfort mode .....................................................................36

Lowering the temperature of your room: how to use Eco mode ........................................37

Programming the heating period: how to use Programming mode ...........................38 to 42

Absence of more than 24 hours: use the Frost Protection mode .......................................43

How to use the energy-saving functions ..........................................................................44 to 48

Locking the controls.........................................................................................................................49

Locking the control panel ..............................................................................................................49

Calibrate the temperature ..............................................................................................................50

Maintenance .......................................................................................................................................50

Returning to the standard factory settings .................................................................................50

Troubleshooting.................................................................................................................................51

Warranty conditions.........................................................................................................................53

GB

27

The device you have just purchased was submitted to many tests and checks ensuring its quality.
We thank you for your choice ant trust. We hope you will be fully satisfied.

The references for your device

These are located on the right-hand side of the device.
The commercial code and the serial number identify for the manufacturer the particular device you

have bought.

Standards, quality labels

A

Commercial name

B

Commercial code

C

Manufacturing reference

D

Serial number

E

Manufacturer’s number

F

Devices with this symbol must not be scrapped with normal household rubbish but be col­lected separately and recycled.
When these products come to the end of their useful life, they must be collected and recy­cled in accordance with the local regulations and bylaws.

Please keep this instruction manual even after installing your device.

- Please ensure that children do not lean on the device or play close to it when it is operating : its

Warning

surface may be hot enough to cause burns to their skin in some circumstances, particularly becau­se their reflexes may not yet have been acquired or aur slower than those of an adult. If there is any
risk, fit a protective grill in front of the device.
This device is not intended for use by persons (including children) with physical, sensory or mental

­disability, or by persons lacking experience or knowledge, unless they have received from a person
in charge of their safety adequate supervision or preliminary instructions on how to use the device.

- Care must be taken at all times to keep children from playing with the device.

- Do not obstruct the grills, even partially (either on the front of the device or underneath it): other­wise the device may overheat.

- If the supply cord is damaged, it must be replaced by a service agentor similarly qualified person in
order to avoid a hazard (applies to units fitted with a supply cord and plug).

- Units fitted with a three core supply cord (brown, blue and black), must be directly connected to hard
wiring by a licensed electrician.

- All work on the interior of the device must be carried out by a licensed electrician.

28

We strongly advise against installing vertical machines above an altitude of 1000m
(risk of faulty operation).
Installing a machine at altitude causes an increase in air output temperature
(of the order of 10°C per 1000m above sea level).
It is forbidden to install a vertical machine horizontally or vice versa.
Do not use the device in mobile, on feets or on casters.

Installation

50 cm

15 cm

PREPARING THE INSTALLATION OF THE DEVICE

Installation guidelines

- This device was designed to be installed in residential premises. In any other case, please call your
distributor.

- Installation must comply with the standards currently enforced in the country of use.

- The device must be supplied with 230V single-phase 50Hz.

-

In damp areas such as bathrooms and kitchens, you must install the connection box at least 25cm above
the floor.

Keep the device away from any draughts that may interfere with its operation (e .g.:
unde r a centrally controlled fan, etc ...).

Do not install the heater under a fixed socket.

The device is fitted with a detection system, whose sensor is located on the front of the device.

Volume 1 No electrical device

Volume 2 Class II IPX24 electrical device

Volume 3 Class II electrical device

GB

Comply with the minimum distances from
any furniture units when positioning the
device.

To optimise absence detection by your device, do not
install it in a closed off corner or behind furniture.

29

UNLOCKING THE DEVICE’S HANGING FRAME

S

2

S1

Drilling
points A

Drilling
points A

Drilling
points B

We recommend that you place the device face down on the floor, taking care to protect its front
surface from scratches.

1

Take a flat-

bladed screw­driver and lift
the slider, taking
care not to
bend it.

3

Swivel the hanging
frame downwards on
the lower brackets S1.

FIXING THE HANGING FRAME TO THE WALL

1 2

Place the hanging
frame on the
floor against the
wall. Locate
drilling points A.

2

While keeping the slider
raised, push the hanging
frame towards the bottom
of the heater to release the
upper brackets S2. We rec­ommend that you wear
protective gloves.

4

Remove the hanging
frame.

Refit the hanging
frame, lining up with
drilling points A to
find drilling points B
(you can also use a

level).

Drilling points A show the position for the lower fas­tenings.

Drill the 4 holes and insert the wall plugs.

3

Use suitable wall plugs when fitting on a

specific support (e.g. plasterboard wall).

Drilling points B show the position for the upper fas­tenings.

Position the hanging frame and screw it

4

down.

30

CONNECTING THE DEVICE

Connection rules and regulations

- The device must be supplied with 230V single-phase current at 50Hz.

- The device’s power supply must be directly connected to the main supply after the circuit breaker
without any intermediate switch.

- The device’s power cable must be connected to the main supply via a connection box. In damp areas,
such as bathrooms and kitchens, the connection box must be installed at least 25cm above the floor.

- An Earth connection is prohibited. Do not connect the pilot wire (black wire) to Earth.

- The installation must be fitted with an all-pole cut-off switch with a contact opening distance of at least
3mm.

- If the power cable is damaged, it must only be replaced by an electrician.

- If you are using the pilot wire and it is protected by a 30mA differential (e.g.: bathroom use), the pilot
wire’s power supply must also be protected on this differential.

Wiring diagram for the heating panel

-

Cut off the power supply and connect the wires as shown in the following diagram:

GB

- You can connect the pilot wire if your home is equipped with a programming unit or controller.
In this case, make the following checks according the selected mode (Comfort, Eco, etc.) to that the
programming instructions are being transmitted correctly:

SIGNAL TO BE
TRANSMITTED

MEASUREMENT
BETWEEN THE
PILOT WIRE
AND NEUTRAL

COMFORT ECO FROST

0 Volt 230 Volts

-115 Volts
negative

31

SWITCH-OFF
OF HEATING
AND POWER

CUT-OFF

+115 Volts

positive

COMFORT

-1°C

230 Volts

for 3 s

COMFORT

-2°C

230 volts

for 7 s

LOCKING THE DEVICE ONTO THE HANGING FRAME

S1

S2

CLIC

1

Position the tilted

device on brackets
S1.

3

Lower the device onto the hanging frame. A
click tells you that the device is fastened and
locked in place.

2

Pivot the device
upwards and lift it to
position it on brack­ets S2.

To unlock the device from the hanging frame, take a flat-bladed screwdriver and push the

slider (located on the top left-hand corner of the hanging frame behind the device) towards
the wall.
Lift the device while holding the slider in place with your screwdriver. Tilt it for-

wards and then remove it from brackets S1.

32

Operation

é

q

u

i

l

i

b

r

e

A

B

C

D

E

F

G

PROG

Prog

ra

m displa

y

ed

Prog

ra

m selection

Airin

g function

Advised Ec

o temperatu

r

e

Day a

n

d time

Ac

tion not possible

C

onsumption indicators

Temper

ature display

or day

a

nd time i

f bein

g

set

C

ont

rols locked

Heating indicator

Modes

Control box

For your comfort and to save energy, your device is equipped with a digital-display control unit. You
can set all of the device’s functions from the unit.

GB

A

Airing function

B

Programming / Ste the correct time and day

C

Increase the temperature / Scroll

D

Turn on / Change heating modes – scroll / Standby

E

Lower the temperature / Scroll

F

Consumption indicator function

G

absence and presence detector

Remove the plastic film on the control unit

The different displays

After 2 minutes of inactivity, the screen returns to the main display.

33

Use

é

q

u

i

l

i

b

r

e

é

q

u

i

l

i

b

r

e

TURNING ON YOUR DEVICE

é

To turn on your device, press the
Power on key (E).

When first turned on, the device is set to Comfort mode at 19°C.

ACTIVATING THE SCREEN

If the screen is not lit up, press any button to activate the screen lighting.

If the screen backlighting is not
active, press any button to reac­tive it.

q

u

E

i

l

i

b

r

e

The device displays the ‘comfort’
temperature.

You can now press the appropri­ate button for the setting you
want to make.

PUTTING YOUR DEVICE IN STANDBY MODE

To put your device in standby
mode, hold the Standby key (E)
down.

é

q

u

r

e

E

i

l

i

b

The panel displays then turns
off.

34

CHOOSING YOUR HEATING MODE

PROG

You can run your device in several modes:

- Comfort mode ( ) which enables you to have the right ambient temperature.

- Eco mode ( ) which enables you to lower the temperature in your room when you will be away

from your home for a long time or during the night, especially in bedrooms.

- The Programming mode, where you can program the Comfort and Eco modes depending
on when the room is used, using programs P1, P2, P3 or using a (centralised) programming system.

- Frost mode ( ) which enables you to maintain a temperature of around 7°C during an absen-
ce of more than 24 hours, for example.

GB

35

HEATING YOUR ROOM :

PROG

HOW TO USE COMFORT MODE

DESCRIPTION

This mode enables you to have the ambient temperature you desire in your room. The consumption
indicator lights enable you to optimise your setting (see page 48).

HOW TO ACTIVATE THIS MODE ?

If the screen is not lit up, press any button to activate the screen lighting.

To activate the Comfort mode,
press the Scroll key (E) several
times until the arrow is on the
Comfort mode.

The advised Comfort temperature is 19°C.
The Comfort mode ranges from 12.5°C to 28°C.

HOW TO CHANGE THE TEMPERATURE

To change the temperature dis­played, press the + (D) or – (F)
keys.

é

q

u

r

e

E

i

l

i

b

The mode selection arrow flashes
for several seconds, then just the

icon remains on the display:

the setting is confirmed.

D

é

q

u

i

l

i

b

r

e

Wait at least 6 hours for the room’s
temperature to stabilise.

The heating icon appears on

F

the screen if the room tempera­ture is lower than the one dis­played.

If you want to change the room
temperature, change it by press­ing the + (D) or – (F) keys.

D

é

q

u

i

l

i

b

r

e

36

As the temperature displayed on

F

the screen rises, the consumption
indicator light descends.

LOWERING THE TEMPERATURE IN YOUR ROOM :

PROG

HOW TO USE ECO MODE

DESCRIPTION

We recommend that you use this mode when you will be absent for 2 to 24 hours, or during the
night, especially in bedrooms.
Maximum Eco temperature is 19°C.

HOW TO ACTIVATE THIS MODE ?

é

Press the scroll key (E) several
times until the selection arrow is
on mode.

q

u

r

e

E

i

l

i

b

The mode selection arrow flashes
for several seconds, then just the

icon remains on the display:

the setting is confirmed.

The advised Eco temperature is -3.5°C compared with the Comfort temperature (setting example: 19°C in Comfort
mode and 15.5°C in Eco mode). If the -3.5°C icon does not appear on the screen, this means that the difference
compared with the set Comfort temperature is not 3.5°C.
If you lower the Comfort temperature to below the Eco temperature, the Eco temperature lowers by -0.5°C com­pared with the Comfort mode If, however, you increase the Comfort temperature, the Eco temperature does not
change.

HOW TO CHANGE THE TEMPERATURE ?

D

If you want, you can change the
temperature displayed by press­ing the + (D) or – (F) keys.

é

q

u

i

l

i

b

r

e

The chosen Eco temperature
appears on the screen.

F

GB

37

PROGRAMMING THE HEATING PERIOD :

PROG

HOW TO USE PROG MODE

You can program your Comfort and temperature times either by using one of the three
prestored programs, or by connecting the pilot wire to a programming control (Pilot wire (FP) mode
is the default setting - refer to your programming control’s manual)
You can connect several devices to one programmer.

3 programs have been prestored: , and and they cannot be changed.

0h 1h 2h 3h 4h 5h 6h 7h 8h 9h

10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 20h 21h 22h 23h

is recommended for when you are constantly at home, at the weekend for example (Eco mode
from 23h to 5h, Comfort mode from 5h to 23h).
is recommended if you are absent during the day (Eco mode from 23h to 5h and from 9h to 17h,
Comfort mode from 5h to 9h and from 17h to 23h).
is recommended if you are absent during the day, but you come back home at lunchtime (Eco
mode from 23h to 5h, from 9h to 12h and from 14h to 17h, Comfort mode from 5h to 9h, from
12h to 14h and from 17h to 23h).

means that a programming control is used.

NB : If no command is received on the pilot wire, the device will function in Comfort mode.

When switching from Comfort to Eco mode, the new mode is active after about 12 seconds.
The Frost Protection and Load shedding commands have priority over the Eco, Comfort and pro­gramming (P1, P2, P3 and ) modes.

38

HOW TO SET THE DAY OF THE WEEK AND TIME ?

Before programming the device, you must set the device to the correct time or make sure that the
system day and time is correct.

To set the day of the week and
the time, hold the Programming
key (C) down for several sec­onds.

To change the day, press the +
(D) or - (F) key.

To set the time, press the Scroll
(E) key.

C

GB

The letters on the screen start
flashing: you can now set the day
of the week.
(J= day - LU = Monday)

D

é

q

u

i

l

i

b

r

e

é

q

u

i

l

i

b

r

e

You have changed the day. You

F

can now set the time.

E

The letters on the screen flash
so that you can change the hour.

To change the hour, press the +
(D) or - (F) key.

D

é

q

u

i

l

i

b

r

e

39

You have changed the hour. You

F

can now set the minutes.

To set the minutes, press the
Scroll (E) key.

To change the minutes, press the
+ (D) or - (F) key.

To confirm the minutes, press
the Scroll (E) key.

é

q

u

i

l

i

b

r

e

E

The letters on the screen flash
so that you can change the min­utes.

D

é

q

u

i

l

i

b

r

e

F

You can now confirm your set­ting.

é

q

u

i

l

i

b

r

e

E

The screen returns to the main
menu.

N.B.: You can exit the settings at any time by pressing the Programming key (C).

The settings made are saved.

40

HOW TO ASSIGN A DAILY PROGRAM ?

C

To access the daily program,
press the Programming key (C).

Two solutions are possible :

a- you want to keep the selected program,

b- you want to change the selected program.

a- You want to keep the selected program – Monday in the example

For Monday, the ‘FP’ program is
selected.
(J= day - LU = Monday -
FP = programming control)

GB

You want to keep the ‘FP’ pro­gram for Monday: press the
Scroll key (E).

é

q

u

i

l

i

b

r

e

E

The program for Monday is con­firmed. You can now select the
program for Tuesday.

b-You want to change the selected program – Monday in the example

You want to change the ‘FP’ pro­gram for Monday: press the +
(D) or - (F) key until the pro­gram you want flashes on the
screen.

é

41

D

q

u

i

l

i

b

r

e

You have chosen the P3 program

F

for Monday, you can now con­firm.

HOW TO ASSIGN A DAILY PROGRAM TO ALL THE DAYS OF THE WEEK ?

PROG

PROG

PROG

PROG

PROG

Carry out the same procedure for all the days of the week, up until Sunday, either keeping the selec­ted program or changing it.

é

Confirm the programs chosen
for each day of the week by
pressing the Scroll key (E).

q

u

i

l

i

b

r

e

E

You have confirmed the daily
programs. You must now activate
the Programming mode.

N.B.: Even if there is a power cut, the settings are saved.

HOW TO ACTIVATE THE PROGRAMMING MODE ?

To activate the Programming
mode, press the Scroll key (E)
until the arrow is on this mode

.

é

q

u

i

l

i

b

r

e

E

The mode selection arrow flashes
several seconds, then remains on
the display with the icon of

the mode being programmed.

N.B.: If the icon blinks, you need to check the day and time settings (see page 39).

42

ABSENCE OF MORE THAN 24 HOURS:

PROG

USING THE FROST PROTECTION MODE

The Frost Protection temperature is preset to 7°C (±3° C) and cannot be changed.

HOW TO ACTIVATE THE FROST PROTECTION MODE ?

é

Press the scroll key (E) until the
selection arrow is on the Frost
Protection mode.

q

u

i

l

i

b

r

e

E

The mode selection arrow flash­es for several seconds then the

icon remains on the display.

GB

43

HOW TO USE THE ENERGY-SAVING FUNCTIONS :

PROG

12 cm

45 cm

20°

5 m

environ

ABSENCE AND PRESENCE DETECTION

These functions enable your device to adapt itself to your daily life without your having to concern
yourself with it.
To use these functions, we recommend that you set the Comfort mode or Programming

mode.

These functions are in addition to the programming functions.

The function enables you to lower the temperature setting for your room automatically, as soon as
you leave it.

Absence detection is made from a height of over 45cm (Diagram 1) and operates progressively (Diagram 2):

Diagram 1

Diagram 2

E.g.: Your device is set to 19°C, in Comfort mode (whether programmed or not)

At 9:00, it detects your absence.
At 9: 30, its operating instructions are set to18°C.
At 10:00, its operating instructions switch to 17°C.

44

HOW TO ACTIVATE THE ABSENCE AND PRESENCE DETECTION ?

To activate it, press the
Sweetcontrol key (A).

If your device detects no one in the room, it automatically lowers the temperature setting progressive­ly to 3.5°C lower than the Comfort temperature setting.

The symbol flashes when it detects a presence.

The symbol for absence /
presence detection appears on

A

the screen.

HOW TO DEACTIVATE THE ABSENCE AND PRESENCE DETECTION ?

GB

To deactivate it, press the

Sweetcontrol key (A).

The symbol for absence /
presence detection disappears

A

from the screen.

45

Optimum zone

HOW TO USE THE ENERGY-SAVING FUNCTIONS :

AIRING FUNCTION

The function enables you to stop the device from heating and to start heating again automatically
when you are airing your room, thereby saving you energy.

We do not recommend the use of the Airing function in corridors and rooms located close to
an entrance door from outside your home or from the garage.

Do not heats the room while it is being ventilated allow you to save energy. If you do not turn off your
heater when a window is open for a long time, the airing function stops your device from heating
when it is not necessary: your heater automatically detects when the window is opened or closed and
therefore saves energy.
Your device reacts to an open or close window according to several variables, especially

- the temperature settings programmed for the room

- the outside temperature

- the location of your heater, etc.

By detecting whether the window is open or closed, the airing function helps you to be environmen­tally friendly: you save energy by not heating your house when you ventilated it.

46

HOW TO ACTIVATE THE WINDOW OPEN AND CLOSED DETECTION ?

To activate it, press the

Aeration key (B).

The operating instructions are for 7°C ±3°C for the whole time that your room is being aired. When you
close the window, your device will return to its initial operating mode.

After 2 hours, the device starts heating again in any case. The maximum expected airing
period is 2 hours.

NB: If the function does not meet your requirements, you can manually stop the device from heating

N

Power on key (E) for several seconds).

The symbol flashes when it is lowering its operating set point.

B

The symbol for absence /
presence detection appears on
the screen.

(press the

HOW TO DEACTIVATE THE WINDOW OPEN AND CLOSED DETECTION ?

To deactivate it, press the

Aeration key (B).

B

The symbol for window
open and closed detection disap­pears from the screen.

GB

47

HOW TO USE THE ENERGY-SAVING FUNCTIONS :

THE BALANCE FUNCTION

Use the Balance function to set your device at an optimum temperature that is just the right balance
between being comfortable and saving energy.

HOW TO USE THE BALANCE FUNCTION ?

D

é

To use this function, press the
Increase (D) and Decrease (F)
keys simultaneously.

This function does not change how you have programmed your device.

q

u

i

l

i

b

r

e

The temperature displayed is

F

19°C in Comfort mode
and 15.5°C in mode.

HOW TO USE THE ENERGY-SAVING FUNCTIONS :

CONSUMPTION INDICATOR

The energy consumed by an electrical heating device depends, among other things, on the tempera­ture required. The temperature recommended by the public authorities is 19°C, in Comfort mode
(15.5°C in Eco mode).

The “Consumption Indicator” function enables you to position yourself in accordance with this
recommended temperature.

Therefore, depending on the temperature required:

- If the black arrow on the screen is placed before the 2nd orange or the red
icon, you can save energy by significantly lowering the temperature you have
asked for.

- If the black arrow on the screen is placed before the 1st orange icon, you can
save energy by slightly lowering the temperature you have asked for.

- If the black arrow is in front of the green icon, you are already at the recom­mended temperature and are already making energy savings.

All the devices in the same room must be fitted with the same function capabilities. The ener­gy-saving functions must be set in the same way on each heater.

48

LOCKING THE CONTROLS

é

q

u

i

l

i

b

r

e

é

q

u

i

l

i

b

r

e

To avoid the control panel being used inopportunely, we advise you to lock it.

HOW TO LOCK THE CONTROLS ?

To lock the controls, press the
following keys simultaneously for
several seconds:

- Aeration (B) and

- Power on (E).

HOW TO UNLOCK THE CONTROLS ?

To unlock the controls, press the
following keys simultaneously for
several seconds:

- Aeration (B) and

- Power on (E).

LOCKING THE CONTROL PANEL

B

E

GB

A lock appears on the screen: the
settings can no longer be changed.

B

E

The lock disappears from the
screen: the settings can be
changed.

You can also lock the control panel using the screw provided.

Remove the screw located inside
the control panel.

Close the control panel’s flap.

Block the flap using the screw.

49

The panel can no longer be
opened, so the controls cannot be
accessed.

CALIBRATE THE TEMPERATURE

é

q

u

i

l

i

b

r

e

é

q

u

i

l

i

b

r

e

Depending on your installation, the temperature you read may be different to the one displayed on
your device. In that case, you can calibrate the temperature displayed.

C

E

Hold the following keys down
simultaneously:

- Programming (C),

- Power on (E).

With the + (D) or - (F) keys,
choose your calibration value
(between -2°C and 2°C).

E.g. The temperature displayed on your device is 20°C.

The temperature displayed on your thermometer is 19°C =>Choose a calibration value of -1°C.
Confirm your choice by pressing the Programming key (C). Your device will heat until the room temperatu­re reaches 20°C.

MAINTENANCE

To maintain your device’s performance, you must dust it approximately twice a year.

Never use abrasive products or solvents.

RETURNING TO THE STANDARD FACTORY SETTINGS

It is possible de return to the standard settings for your device.

Hold the following keys down
simultaneously

- Aeration (B),

- Settings (C),

- Scroll (E),
until everything is displayed on the
screen (see page 33 for the different
displays).

C

E

The device switches to Comfort

B

mode at 19°C. The mode
is at 15.5°C. The energy saving and
programmed functions are deacti­vated.

50

TROUBLESHOOTING

PROBLEM

ENCOUNTERED

The heating light flas­hes

The device does not
heat.

The device heats all
the time.

The device heats
even though the win­dow is open.

The device does not
heat enough.

CHECKS TO BE MADE

The temperature probe is disconnected or is faulty.
Contact your installer.

Make sure that the mode is activated.
If you are operating under programming, check that the programmer is in
COMFORT mode.
that the power cut-off (if you have one) has not cut off the power to the device.
Check the air temperature in the room: if it is too high, the heating light does
not flash : the device does not heat.

- Check that the device is not in a draught or that the temperature setting has
not been altered.

- There may be a fluctuation in the main power supply. If there is a problem
(blocked thermostat...), cut off the power to the device (fuse, circuit breaker) for
approximately 10 minutes and then switch it back on.

- If the phenomenon recurs frequently, have your electricity utility check the
power supply.

There may be a delay between when the window is opened and when the
heating stops.
If you find this delay too long, you can manually stop your device.

Increase the temperature settings by pressing the + (E) key.
If the setting is at its maximum, carry out the following checks :

- Check whether there is another heating device in the room.

- Make sure that your device is only heating the room (door closed).

- Check the supply voltage to the device.

- Check that the power of your device is adapted to the size of your room
(on average, we recommend 100 W/m² for a ceiling height of 2.50 m).

Ensure that the installation’s circuit breakers are engaged and

GB

The heating light
appears on the
screen when the
device is in Eco
mode.

Dirty marks appear
on the wall around
the device.

This is normal. The device can heat to maintain an Eco temperature.

The dirty marks come from the bad quality of the air in the room. In this case,
you are advised to check that the room is correctly aired (ventilation, vent duct,
etc.), that the air is clean and not to smoke in the room. Your device will not
be replaced under guarantee because of these dirty marks.

51

PROBLEM

ENCOUNTERED

The device’s surface
is very hot.

It is normal for the device to be hot when it is operating; the maximum sur­face temperature is restricted in accordance with the NF electrical perfor-

CHECKS TO BE MADE

mance standard. However, if you think that your device is still too hot, check
that the output is suitable for the area of your room (we recommend 100W /

m2) and that the heater is not placed in a draught, which would interfere with

its self-regulation; also check that the installation guidelines have been fol­lowed (curtains, etc.)

For devices equipped with a programming system or controlled via a pilot wire:
The device is not
responding to the
external program­ming commands.

Make sure that the central programming system is working correctly (refer to
the user manual), or that the programming control is correctly placed in its
holder and that it is working correctly (check the batteries, fuse, etc.)
Make sure that your device is in Programming mode and that the external
“Centralised” program is assigned to the right day of the week.

If you do not succeed in solving your problem, contact your local installer and have the
details of your device’s references (see page 28), the room’s temperature and the pro­gramming system (if any) to hand.

52

WARRANTY CONDITIONS

- The guarantee period is two years from the date of installation or purchase and may not exceed 30
months from the date of manufacture in the absence of a receipt.

-The guarantee covers the replacement and supply of components recognised as being defective,
excluding any damages or interest.

- The user is responsible for any labour or transport costs.

- The guarantee does not cover any damage arising from improper installation, abnormal use or non­observance of the requirements of the said instructions for installation and use .

- The stipulations of the present guarantee conditions do not exclude any of the purchaser’s legal
rights of guarantee against faults or hidden defects, which are applicable in all cases under the sti­pulations of Articles 1641 of the Civil Code.

- Present this certificate to your distributor or installer only in the event of a claim, together with
your purchase invoice.

TYPE OF DEVICE*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SERIAL NUMBER*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

CUSTOMER’S NAME AND ADDRESS: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

* This information can be found on the information plate situated on the left-hand side of the device.

ATLANTIC INTERNATIONAL

Tel: [phone]

Fax: [phone]

FOR SALES IN NEW ZEAL

ANDATLANTIC AUSTRALASIA - Phone :

0800 422 000 - Fax : [phone]

INSTALLER’S STAMP

FOR SALES IN AUSTRALIA

ATLANTIC AUSTRALASIA PTY LTD

4/13-25 Church Street

Hawthom Victoria 3122

Australia

Free call : 1800 677 857

Phone : [phone]

Fax : [phone]

web : www.atlantics.com.au

FOR SALES IN THE U.K.,

please contact :

ATOUR ATLANTIC LTD

Malling Works, Lewes
East Sussex BN7 2AY

Phone : [phone]

Fax : [phone]

E-mail : [e-mail]

53

RYHG SEPT 12 12-80-1293-B