Page 1
1
1.
2.
3.
4.
5.
6.
GPS
GSM
BATTERY STATUS
USB
SIM
WIRING HARNESS
2
3
4
5
6
Model No.
L-100
Innovative ICT Solutions
LED Indication
20.
USER MANUAL
L-100
MANUAL VERSION # L100_V0.1
Table of content
1. INTRODUCTION--------------------------------1
2. PACKAGING CONTENTS--------------------2
3. PRECAUTIONS ---------------------------------3
4. INSTALLATION PROCEDURE-------------4
5. SMS COMMANDS DISCRIPTION------------5
6.TROUBLE SHOOTING-------------------------6
PACKAGING CONTENTS:
Unpack the L-100 Box carefully, in the package
you may find:
1. L-100 Tracking Device
2. Wiring harness
3. Fuse
4. Relay with socket *
5. Panic button*
6. User manual
v Note-Some of the accessories shown above are
optional and need to be purchased separately
18.Over The Air (OTA) software updatio n.
USER MANUAL
L-100
Features
1. High sensitive GPS chipset.
2. Combination of GPS, GSM/GPRS wireless
network.
3. Durable and highly reliable GPS tracker.
4. Easy to install or hide in the vehicle to perform
tracking.
5. Ideal for vehicle tracking and equipment/assets
monitoring.
6. External DC power supply.
7. Configuration can be done via SMS commands.
8. Real-time GSM/GPS location monitoring on SMS
and website.
9. Vehicle control with Immobilization.
10.Generation of reports on web-site in html/xls
format. Reports include drive/stop summary,
performance (based on speed), detail (with time,
date, latitude, longitude, speed).
11.Replay and analysis of trip logs.
12.Add on users with customized access to web
accounts
13.Door sense.
14.Vehicle control function (Ignition off/on) can be
started /stopped by the user..
15.Easy installation and easy SMS commands.
16.If wrong SMS command sent by the user then, L-
100 will delete SMS and send “SMS NOT
ACCEPTED” to user mobile number.
17.User would get a map link on mobile with
Latitude /longitude.
· Insert SIM card in to the SIM Slot as shown, make
sure that the mobile number is recorded
· LED indicator started glowing, if the internal
Battery is charged
v Note:- Inserting SIM card will switch ON the device
so remove the SIM card if the device is not fitted to
vehicle to save internal battery.
· Connect the device to the wired harness and wait for
Indicators.
· Within 10 to 40 seconds,the unit will begin to work
and acquire the GSM signal as well as the GPS
signals.The GSM indicator (GREEN LED) will flash
when the unit has registered with GSM network.
· Once the GPS signal is valid. The GPS indicator
(BLUE LED) starts blinking.
· Both the indicators would be “ON”, if no GSM &
GPS signal available.
· RED LED- Indicates the battery charging, if LED is
ON means Battery charging, Blinking means
battery FULL
· Use the following SMS commands to configure
and start tracking.
19.User can take the ODOMETER reading on Mobile
as well as on website.
20.Panic Button can be used to generate SMS in\
case of emergency.*
*Note:-This function will work if you have additionally
purchased the Panic Button Kit.
PRECAUTIONS:
While washing the engine, protect the L-100 by all
suitable means from being struck directly by water jet
or flow.
The GSM functionalities are dependent on the network.
postpaid/prepaid SIM card can be used.
Pay special attention to the amount of remaining credit
& expiry date of mobile connection in case of prepaid
SIM card.
“ARM MODE” commands will immediately bring the
vehicle to a sudden halt. Hence, we strongly
recommend that these commands should not be used
when vehicle is moving, as sudden stop may result in
some mishappening.
HARDWARE DESCRIPTION:
a. Power Requirement: 8V to 40V
b. Normal operation temperature: -30°C to +80 °C
c. Restricted operation temperature: Above -40°C
and below +85 °C
d. Storage temperature: -45°C to +90°C
e. Humidity: 5% to 95%
INSTALLATION PROCEDURE:-
Steps:-
Set up the required wiring as per the wiring diagram
using the Harness and Fuse provided in the package
· Open the Green strip as shown.
LED Indication
· RED: Battery charging indication, ONà Battery
charging, Blinkingà Battery charged.
· GREEN: GSM indication, ONà out of network,
Blinking at every sec.à GSM signal available.
· BLUE : GPS indication, ONà GPS NOT FIX, Blinking
at every sec.àGPS FIX
SMS COMMANDS DESCRIPTION:
1. PW::1234;<password> - This command is used to
change the password. After this command the
password will be 1234
2. SYSSTARTZ::+919876543210;<password>
This command is used to register the L-100 with
Subscriber number. Now L-100 will send alerts to the
number +919876543210. Confirmation message
“SYSTEM START HAS BEEN ACTIVATED” will be
received.
3. SYSSTOPZ<password>
This command is used to stop the system with
Subscriber number. (Now a new number can be
registered with L-100).
4. IMEI<password> -L-100 will display International
Mobile Equipment Identity Number (15 Digits).
5. ARM<password> -L-100 will start monitoring the
vehicle. It will start sensing the doors & ignition, cut
the ignition of the vehicle and confirmation message
“ARM MODE HAS BEEN ACTIVATED” will be
received.
7.#CONFIG::APN::username::password;<password>
–This command is used to configure GPRS
settings
APN (access point name) which is used to get to the
GPRS gateway provided by network operator.
get
Page 2
TROUBLE SHOOTING:
S.NO SCENARIO IN
GENERAL
TROUBLE SHOOTING
1. No LED indication
· Ch eck SIM card position
· Ch eck the Harness wiring
2. GREEN LED not
blinking at 1 sec.
interval
· Ch eck SIM card validity
· Ch eck SIM security settings(No PIN
reccomended)
3. BLUE LED not
blinking
· Ch eck the side marked as “THIS
SIDE UP” is facing
sky.
· K eep the device in open space for 23 minutes for GPS fix.
4. SMS not
accepted :
“WRONG
COMMAND”
There may be some spelling mistake in the
command or the command may be invalid.
Please recheck the command phrase and
resend.
5. No response from
L-100:
· Ch eck your balance in case of
prepaid connection.
· Ch eck the network status. (No or
weak network connection could be
the reason)
· Re send thedesired commands again.
· Re set the L-100.
· Ch eck the password
6. SMS is not
Delivered:
Please check the network status.
7. “NO DATA” from
device
· Ch eck GPRS availability of SIM card
· Ch eck server settings
· Ch eck “GPRSSTATUS” for various
settings
8. I/O status not
Proper/ not getting
Alerts
· Ch eck harness wiring
· Re gister the controlling number.
Username: for your GPRS account, username is
provided by network operator or else leave it blank,if
advised by network operator.
Password: for your GPRS account, password is
provided by network operator or else leave it blank,if
advised by network operator.
8.#CONFIG?<password> - This command replies with
GPRS APN, User Name and Password already
saved.
Response:
1).APN: XXX,(GPRS USERNAME:)XXX,(GPRS
2).PASSWORD)XXX
9. To start live tracking on internet :
Send “WEBSTART<xxx/H/M/S><password>” to L100, L-100 will send confirmation SMS and then start
sending data to our web server.
· xxx means digits from 001-999
· H means HOURS,M means MINUTES,S means
Seconds
Example – when we send the command
WEBSTART002M<6906>, L-100 will start sending the
data to web server at 2 minutes interval.
1. DBT<xxxM/K><password>” L-100,will send
confirmation SMS and then start sending data to our
web server as soon as covering the set distance and
on deviation of 50 degree from the normal course.
· xxx means digits from 001-999
· M means METERS, K means KILOMETERS
Example – when we send the command
DBT5OOM<6906>, L-100 will start sending the data
to web server at every 500 meters and on deviation
of 50 degree from the normal course..
10.SDBT<password> :-this command will stop the
distance and angle based tracking
11.To port the device to a server
Command to port the L-100 to the required server
(with IP and PORT)
tracking will start sending data again. This mode is
provided to save battery when the Vehicle is in stand still
#SERVERCHANGE::IP::PORT;<password>
Example:-
#SERVERCHANGE::196.168.175.12::20000;<6906>,
this command would point
L-100 to the server with IP=196.168.175.12 and Port=
20000.
1. To get GPS data for one time
Send “GETGPS<password>” to L-100
Response:
L-100 will send:
1) If the GPS satellites are unreachable, you will receive
“GPS NOT FOUND”
2) If the GPS satellites are reachable, you will receive
Web link to view location (It will show you the location
on map)*
Speed: XXX (It will tell you the speed of the vehicle in
KMH)
Date: XXX (It will tell you the date of this particular
data)
Time: XXX (It will tell you the time of this particular
data in IST)
To observe the exact location on Google map for a
corresponding LAT – LONG, open www.maps.google
.com, in the search bar enters the latitude and
longitude coordinates separated with a comma (,). It
will show you the location.
2. SLEEPON<password>:
Sleep mode is used to deactivate data sending on
GPRS when the vehicle is stationary for a particular
time. As soon as the Vehicle starts moving again the
1. SLEEPOFF<password>
This command is used to disable SLEEPON mode
v Note:-By default sleep mode is OFF.
10.SDL::XXX;<password>
This command is used to set the number of data
packets to be saved in the memory in sleep mode.
The default value for the same is 25, means in sleep
mode the device would save 25 packets as per
tracking interval and then send all the data from
memory once the memory data count became 25.
11.SYSSTATUS<password>
Response:
MPON/MPOFF Main power status
IGNON/IGNOFF Ignition status
ARM/DISARM Immobilizer status
A/C ON/A/C OFF A/C status
DOOR OPEN/DOOR CLOSED DOOR status
LS HIGH(R)/LS LOW(R) Reserved low sense input
DBGON/DBGOFF No meaning
BP: 95 Battery level in percentage
12.SETODO::12345; <password> -- This command is
used to calibrate the odometer where 12345 is the
present odometer reading.
13.SETODO? <password> --- This command is used
to get/read the present accelerometer reading of
vehicle.
14.CO?<password> ------------------This command is
used to check the GSM operator name.
15.GPRSSTATUS
This command is used to get the complete status of
the device, and the command format is
GPRSSTATUS<6906>.
Description of the reply
Entries Description Remark
CN: Current network
SOFF Sleep status SOFF for SLEEPOFF
and SON for SLEEPON
SS GSM Signal
strength
Should be >10 for
proper GPRS comm..
CC Current
configuration
Currently using
APN,UN,PWD
IP Server address Currently using Server
details(IP,PORT)
WTI Webtracking
interval
Web tracking interval
IMEI IMEI of device IMEI of device
DID Device ID 15 Char Device ID
GPS GPS availability A= available, V= void
SF Data sending fail
CF Connection fail
with server
PD PDP Deact error Network error occurs
normally if APN is
wrong
MUC Internal memory
data count
SDL Sleep Data
LIMIT
No. packets saved in
sleep(25 default)
16.Single command to set all parameters for tracking
#CC::APN,APNusername,APNpassword,IP,PORT,Tr
ackingInterval,SDL;<password>
Where APN:_ is the APN of network, APNusername:_
Username of operator, APN password:_ Password of
operator, IP:_ IP of server to which data is to be sent,
PORT:_ Port number of the server, Tracking interval
of device, SDL:_ Sleep data limit(Number of packets
to be saved in sleep mode)
Eg:
#CC::airtelgprs.com,abc,12345,12.32.43.54,222,030S
,25;<6906>
v Note: commands starts with “#”are case sensitive
Indian Standard Time.
recommended)
Check response of “GPRS STATUS”
command for various GPRS parameters.
I/P HIGH2/ AC
86
85
30
87A
87
VEHICLE
SWITCH
Accecories
RELA
Y SPOT
+12/24V
ADC INPUT
GND
Battery
-
+
L-100
10
9
8
7
6
5
4
3
2
1
White
Black
DOOR SENSE
NC
NC
P
ANIC BUTT
ON
BUTT
ON
I GN SENSE
I GNCTRL
Features
Anti theft
Base station positioning
Built in antenna
Low voltage alarm
Vibration alarm
Speeding alarm
Sleeping mode for saving power
Geofence
working voltage
Working current
GSM frequency
GPS sensitivity
GPS accuracy
Cold start
Warm
Hot start
Working
temperature
Humidity of storage
Relative humidity
Backup battery/
Working time
Size
Net weight
Specifications
Tracking via SMS
Small size
Water proof
Power cut off alarm
Displacement alarm
Dormant lock anti theft
Mileage statistics
Trace play back
8-40v
Sleeping mode< 6mAh;working mode <70mAh
GSM850/EGS900/DCS1800/PCS1900
-159dBm
Better than 5meter
50-1000 meters
0.1 meter/s
Less than 35s
Less than30s
Less than 2s
-30C~+70C
-40C~+85C
<95%
3hours
84mm x 50mm x 16mm
68gm
o
o
o
o
-
-
-
Loading...