Ativa 061506-5OD, 061506-OD User Manual
061506_OD LCD Manual 6/15/06 4:57 PM Page 1
Instructions For Shredder With
Liquid Crystal Display (LCD)
Instructions pour la déchiqueteuse
avec affichage à cristaux liquides (LCD)
Instrucciones para Trituradora con
Pantalla de Cristal Líquido (LCD)
061506-5OD
ON/OFF
Maintain
Reverse Forward
ON/OFF
Maintain
Reverse Forward
ON/OFF
Maintain
Reverse Forward
061506_OD LCD Manual 6/15/06 4:57 PM Page 2
Powering ON (Some Models)
The master power switch is located on the rear of
he shredder head. When the switch is turned on,
t
the LCD displays all of the operating functions
and gives a beep (See figure on left). Two seconds after the characters are shown, the display
clears and enters the standby mode.
ON Mode
When pressing the ON/OFF button for more that
three seconds, the LCD shows AUTO and enters
AUTO mode. In the AUTO shredding mode, the
shredder stands ready to shred paper, If there is
any paper stuck at the throat in the shredder, the
shredder will automatically shred the paper. The
shredder will stop after the paper is completely
shredded.
OFF Mode
When pressing the ON/OFF button for more that
three seconds, the shredder will beep once and
shut off all functions, entering into standby
mode, the LCD will turn off. If you wish to restart,
press and hold ON/OFF button for more than
three seconds to start.
REVERSE Mode
When pressing the REVERSE button, LCD shows
the character of REVERSE and the motor enters
the REVERSE mode. Press and hold the REVERSE
button in order to keep the motor running in
reverse. When the REVERSE button is released,
the motor will stop. If there is any paper left at
the throat, the shredder will enter into the AUTO
shredding mode and the display will show AUTO.
REVERSE Mode, when shredding in AUTO mode
During for
war
edding, if the REVERSE button
d shr
is pressed, the motor will stop immediately. After
three seconds, the motor starts reversing while
the LCD shows REVERSE. Pr
essing the REVERSE
button will keep the motor running. The shredder
will not stop until the button is released. After
the motor stops, if there is still paper remaining
in the throat, the shredder will resume AUTO
edding and the LCD will display AUTO.
shr
2
O
N/OFF
M
aintain
R
everse Forward
ON/OFF
Maintain
Reverse Forward
ON/OFF
Maintain
Reverse Forward
061506_OD LCD Manual 6/15/06 4:57 PM Page 3
FORWARD Mode
When pressing the FORWARD button, the LCD dis-
lays AUTO and the motor enters the FORWARD
p
mode. Press and hold the FORWARD button in order to
keep the motor running forward. When the FORWARD
button is released, the motor will stop.
OVERLOAD Mode
When the shredder overloads during shredding,
the motor will stop running and the LCD will
flash the OVERLOAD icon. Press the REVERSE button the motor will start reversing and the LCD
will show REVERSE. When the overloaded paper is
removed from the throat, the LCD will show
OVERLOAD, the motor will start running for three
seconds and the shredder will start automatically
clearing any papers. After the motor stops, the
LCD will show AUTO.
If user cannot remove the paper from the throat
by pressing the REVERSE button, tear off the
remaining paper and press ON/OFF to shut off
the shredder. Press ON/OFF again to start shredding and clean out the paper. If unable to clean
out the paper in one action, repeat the above
process until the paper is completely removed
and the LCD displays AUTO.
DOOR OPEN Mode
When the paper bin is pulled out or the bin door
is opened while shredding, the motor will stop
immediately and sound the alar
m. The LCD will
flash DOOR OPEN. To resume normal function,
the bin or door must be placed back to original
position. The LCD will show AUTO.
3
061506_OD LCD Manual 6/15/06 4:57 PM Page 4
OVERHEAT Mode
If the shredder overheats, the LCD will flash OVER-
EAT. Both AUTO and REVERSE functions will stop.
H
When the shredder overheats, user may press
ON/OFF to place the shredder in stand by mode.
The shredder will not resume normal functioning
until the temperature of the motor cools down to
a safe temperature and LCD shows AUTO.
MAINTAINENCE
After 500 shredding cycles, the LCD will flash
MAINTAIN. This indicates that the shredding
blades need to be lubricated using an approved
shredder lubricant. Only shredder lubricant
sheets or bottled lubricant designed specifically
for shredders should be used. Follow the instructions provided with the shredder lubricant.
NEVER USE AN AREOSOL LUBRICANT, or any lubricant that is flammable. Refer to the warnings provided in your shredder manual.
MANUAL MAINTAINENCE
The shredder will continue to operate in a normal
manner while the MAINTAIN light is flashing.
After applying lubricant to the cutting blades, the
MAINTAIN light can be deactivated by pressing
and holding the MAINTAIN button for 7 seconds.
The shredder will return to AUTO mode, the LCD
will clear the word MAINTAIN, and the internal
counter on the shredder will be reset to zero.
AUTOMATIC MAINTAINENCE
(Optional feature, not present on all shredders)
If there are shredder lubricant sheets in the sheet
basket, the shredder will automatically lubricate
the blades. The LCD will display the picture of a
lubricant sheet. After the motor stops, the internal counter will be rest to zero
BIN FULL Mode
(Optional feature, not pr
esent on all shredders)
The motor will stop and sound alert when the bin
is full. The LCD will flash BIN FULL. All shredder
functions will stop. If the paper bin or the door is
open, the LCD will flash DOOR OPEN. After the
bin is emptied and placed back to nor
tion, the LCD will show AUTO and r
mal posi-
esume nor
mal
functioning.
4
Loading...