ATI Technologies 100-505139 - FireMV 2200 PCI 64M DDVI, FireMV 2400, FireMV 2200 Quick Installation Manual

FireMVTM2200
Connecting the Monitor(s)

Your FireMV™ 2200 can drive up to two display devices
simultaneously (analog or digital) and will allow for
independent resolutions.

1. Plug the Y-cable into the DMS-59 connector on the
FireMV™ 2200. Connect the DVI-I cable of your
monitor to the DVI-I “1” connector on the Y-cable. To
connect a VGA monitor to a DVI-I connector, use the
included DVI-I-to-VGA adapter.

2. If using a second display, plug it in to the DVI-I “2”
connector on the Y-cable, using the DVI-I-to-VGA
adapter if necessary. For more information consult
your FireMV™ 2200 User Guide on the installation
CD.

Installing the Card

1. Turn off your computer and monitor(s).

2. Disconnect any existing monitor cable(s) from the
back of your computer.

3. Remove the computer cover. If necessary, consult
your computer manual for assistance.

4. Discharge any static electricity by touching the metal
surface of the computer chassis.

5. Remove any existing graphics card(s) from your
computer. Save any screws used to secure the card.

6. Locate the PCI or PCI Express™ (PCIe) X16 slot, if
necessary, remove the metal backplate cover and
save any screws.

7. Align your FireMV™ card with the PCI or PCI
Express™ X16 slot, then press it in firmly until the
card is fully seated. When handling the card, hold it by
its edges, and avoid touching its circuitry.

8. Replace the screws on the top of bracket to fasten the
card in place.

Installing the Software Drivers

1. Turn on your computer and display device(s).

2. Insert the FireMV™ installation CD.

3. Click on “Install Software” and follow the on-screen
instructions.

4. Open the Windows® Control Panel > Display to
configure your display settings.

Troubleshooting

If you experience any problems during installation, double
check the steps above.

Troubleshooting information may be found on the ATI web
site at ati.com/FireMV.

Your ATI FireMV™ installation CD contains a User’s Guide
in Portable Document Format (PDF). The User’s Guide
describes in detail the features and functions of your ATI
FireMV™ card and the associated software.

Don’t forget to register your new product at:
ati.com/FireMV

FireMVTM2400
Connecting the Monitor(s)

Your FireMV™ 2400 can drive up to four display devices
simultaneously (analog or digital) and will allow for
independent resolutions.

1. Plug the Y-cable into the VHDCI “A” connector on the
FireMV™ 2400. Connect the first DVI-I cable from
your monitor to the to the DVI-I “Mon 1” connector on
the Y-cable. Connect the second DVI-I cable from
your second monitor to the DVI-I “Mon 2” connector
on the Y-cable. To connect a VGA monitor to a DVI-I
connector, use the included adapter.

2. Plug the Y-cable into the VHDCI “B” connector on the
FireMV™ 2400. Connect the third DVI-I cable from
your monitor to the DVI-I “Mon 3” connector on the Y­cable. Connect the fourth DVI-I cable from your fourth

monitor to the DVI-I “Mon 4” connector on the Y-cable.

To connect a VGA monitor to a DVI-I connector, use
the included adapter.

Warranty Information

Should your ATI FireMV™ product malfunction within the warranty period, ATI will at its discretion repair or replace the product upon receipt of the product. Any replaced parts

become the property of ATI. This warranty does not apply to the software component of a product or a product which has been damaged due to accident, misuse, abuse,

improper installation, usage not in accordance with product specifications and instructions, natural or personal disaster, or unauthorized alterations, repairs, or modifications.

For a detailed description of the ATI Hardware Warranty Service Statement visit http://ati.com/online/warranty/statement

Limitations

All warranties for this product, expressed or implied, will expire three (3) years* from date of original purchase. All accompanying cables and accessories are warranted for 90

days. No warranties for this product, expressed or implied, shall extend to any person who purchases the product in a used condition.

The liability of ATI in respect of any defective product will be limited to the repair or replacement of such product. ATI may use new or equivalent-to-new replacement parts.

Defective product will be sent in for repair or replacement only.

ATI makes no other representations or warranties as to fitness for a particular purpose, merchantability or otherwise in respect of the product. No other representations,

warranties or conditions, shall be implied by statute or otherwise.

In no event shall ATI be responsible or liable for any damages, including but not limited to the loss of revenue or profit, arising from the use of the product, or from the loss of

use of the product, as a result of any event, circumstance, action or abuse beyond the control of ATI; whether such damages be direct, indirect, consequential, special or

otherwise and whether such damages are incurred by the person to whom this warranty extends or a third party.

Copyright © 2005 All rights reserved.

No reproduction of this document in any form is permitted without prior written authorization from ATITechnologies Inc.

All registered trademarks are the property of their respective owners.

P/N 5000028200 Printed in Canada

Quick Installation Guide

ati.com/FireMV

Introduction

This guide provides a quick overview of the steps required to install your new graphics card.Complete documentation for
your FireMV™ card is available as a Portable Document Format (PDF) file on the FireMV™ driver CD, or available for
download at ati.com/FireMV.

Register Online

Please register your FireMV™ card at ati.com/FireMV. To complete the product registration you will need to know the part
number of FireMV™ card you purchased and the serial number.These numbers are listed on a sticker on the back of the
card, and on the box. For future reference write this information in the space provided below before installing the card:

Part Number: __________________ Serial Number: ____________________ Purchase Date: ___________________

Installation Requirements

• Computer with one available PCI Express™ x16 lane slot or PCI slot for PCI card.

• 128MB of system memory (256MB recommended for better performance).

• CD drive or Internet connection for software driver installation.

• Supported operating systems:

- Windows® 2000 with Service Pack 1 (or higher) or Windows® XP

Customer Care

Advanced technical support for FireMV™ products is
available from ATI’s dedicated frontline support team via
the internet, email or toll free telephone number.

ATI offers an Advanced Parts Replacement Service. For
more details or to request a Return Merchandise
Authorization (RMA) please contact an ATI Customer
Care Representative.

For product information and driver updates visit
ati.com/FireMV.

Contact Information

Internet:

ati.com/FireMV

Phone: North America

1-866-284-2093
or 905-882-2651
(Monday - Friday, 9:00 AM - 7:00 PM EST)

Europe
[phone]
(Monday - Friday, 10:30 AM - 19:00 GMT)

Mail:

ATI TECHNOLOGIES INC.
Attention: Customer Care
1 Commerce Valley Drive East
Markham, Ontario
Canada L3T 7X6