ATI Electronics H710 Users Manual

如何使用藍牙耳機？

如何安裝手機／充電？

相容性

本產品經MFi認證，適用於iPhone 7/ iPhone 6S/ iPhone 6

重要安全事項

本產品需置於陰涼乾燥處保存，使用環境溫度為-15℃至 45℃，建議在0℃至30℃環境下存放。

請勿在低於-15℃之環境使用耳機。

請勿靠近火源，可能產生產品爆炸之危險。

請勿將本產品存放於亦濺水或長期潮濕的環境。

請勿拆卸、重組本產品，可能造成損害。

充電過程中，產品發熱屬正常現象。

請於指定回收中心回收電池。

請避免孩童接觸本產品，以避免誤食小型零部件之意外。

本設備符合FCC規則第15部份中的規範。操作設備符合以下兩個條件：

1.此設備可能不會產生有害的信號干擾。

2.本設備必須接受任何的干擾，包含可能引起不期望操作的干擾。

耳機開機

首次配對

拔出耳機，指示燈會亮起指示燈閃藍／紅光時即可和手機配對

未連接狀態長按接聽鍵可清除耳機的配對資料

接聽鍵功能

待機

按1下播放音樂

語音/Siri

按2下

- -

長按

接聽鍵

指示燈

音樂中來電通話中

暫停音樂接聽來電掛斷通話

語音/Siri

耳機將自動關機並開始充電

指示燈亮紅光/充飽即熄滅

通話中，將耳機插入會自動掛斷電話

保持通話拒接來電

耳機開機

耳機充電

將耳機插入保護殼

隨拔即用

將耳機拔出保護殼會自動開機並立即回復和手機的藍牙配對

來電時，將耳機拔出會自動接聽電話

注意：耳機在無連接的狀態下

2分鐘內會自動關機

此時請將耳機插入保護殼再次拔出時即可開啟耳機

將耳機插入保護殼

耳機將自動關機並開始充電

安裝手機

將Lighning滑塊卸除後可輕鬆將手機放入保護殼之後請插上Lightining滑塊並確認連接器緊密安裝

同步充電

使用Micro USB傳輸線充電時會將手機／保護殼／藍牙耳機全部充滿也可以透過傳輸線和電腦同步手機不需將保護殼卸除

Lightning 滑塊

按住保護殼背面的電源鍵約3秒

便可開始對iPhone充電

按一下指示燈會顯示目前的電量

指示燈閃爍時表示為低電量

請盡快以Micro USB傳輸線充電

電源鍵

指示燈

開始充電

Compatibility

MFi certiﬁed, compati iPhone 7/ iPhone 6S/ iPhone 6

Important safety instructions

Keep the case in cool and dry place. Operating temperature is between -15℃ and 45℃,and recommended temperatures between 0 and 30℃.

Do not use retractable earphone when temperatures are below -15℃.

Do not place product near or directly into ﬁre, as this may cause it to explode.

Do not splash the product, or store in a wet environment long term.

Recycle depleted batteries in designated recycling centers.

Do not disassemble the product as this may cause damage.

It is normal for the case to warm up during charging.

Do not give to children as a toy. Some small parts may be swallowed by accident and cause children to choke.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device may cause interference received, including interference that may cause undesired operation.

NOTE 1: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

How To Use Earphone? How to Install／Charge？

Power Button

耳機開機

First Pairing

Pull the earphone out and the LED Indicator will ﬂash with red/blue light, which means you could pair it with your phone

Pressing the Power Button until it ﬂashes will clean paired proﬁle

Functions

Standby

1-Click Play

Call Siri*

2-Click

Long Press

*Depends on iPhone’s setting, it will call Siri or Voice Control

Playing Call Coming Talking

Pause Accept Hang up

Call Siri*

- -

the earphone will be turned oﬀ and

The LED Indicator will be red until

the earphone is fully charged

The call will be hanged up if the

Pull the earphone out, it will be

it will be picked up automatically

Notice:

1.The earphone will be shut down if no devices are ready to be paired in 2 minutes.

2.Please insert the earphone into the case to activate it again

3.Inserting into the Case, the earphone will be

turned oﬀ

turned on and paired again

LED Indicator

- -

HoldReject

Earphone

耳機開機

Charging

Inserting into the Case,

be charged automatically

earphone being inserted

Pull & Pick

Pull when call is coming,

Installation

Detach the Lightning Dongle to install your iPhone nice’n easy. Please make sure to plug the dongle back tightly

Charge All

With single Micro USB cable, you can charge BB Case, the Earphone and your iPhone Simultaneously Also, to sycn with itunes

Lightning Dongle

Press the Power Button behind the

it will start to charge your iPhone

Press it shortly to show the status

If the LED indictaor ﬂashes,

please use the Micro USB cable to

Power Button

LED Indicator

re-charge the BB Case

Charging

Case for 3 seconds,

Quick-Start Guide