ATHEROS, 5-UP, Driving the Wireless Future, Atheros Driven, Atheros Turbo Mode, and the Air
is Cleaner at 5-GHz are trademarks of Atheros Communications, Inc. The Atheros logo is a registered
trademark of Atheros Communications, Inc. All other trademarks are the property of their respective
holders.
Subject to change without notice.
Notice
The information in this document has been carefully reviewed and is believed to be accurate. Nonetheless,
this document is subject to change without notice, and Atheros Communications, Inc. (Atheros) assumes no
responsibility for any inaccuracies that may be contained in this document, and makes no commitment to
update or to keep current the contained information, or to notify a person or organization of any updates.
Atheros reserves the right to make changes, at any time, in order to improve reliability, function or design
and to attempt to supply the best product possible. Atheros does not represent that products described
herein are free from patent infringement or from any other third party right.
No part of this document may be reproduced, adapted or transmitted in any form or by any means,
electronic or mechanical, for any purpose, except as expressly set forth in a written agreement signed by
Atheros. Atheros or its affiliates may have patents or pending patent applications, trademarks, copyrights,
maskwork rights or other intellectual property rights that apply to the ideas, material and information
expressed herein. No license to such rights is provided except as expressly set forth in a written agreement
signed by Atheros.
ATHEROS MAKES NO WARRANTIES OF ANY KIND WITH REGARD TO THE CONTENT OF THIS
DOCUMENT. IN NO EVENT SHALL ATHEROS BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL SPECULATORY OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBLITY
OF SUCH DAMAGES. IN PARTICULAR, ATHEROS SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA TRANSMITTED OR OTHERWISE USED WITH THE PRODUCT,
INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR
RECOVERING SUCH HARDWARE, SOFTWARE OR DATA. ATHEROS SPECIFICALLY DISCLAIMS
THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE
AS THEY MIGHT OTHERWISE APPLY TO THIS DOCUMENT AND TO THE IDEAS, MATERIAL AND
INFORMATION EXPRESSED HEREIN.
Document Number: 984-00023-003
ii•AP User’s GuideAtheros Communications, Inc.
ii•March 2003COMPANY CONFIDEN T I AL
Document Conventions
Text Conventions
boldBold type within paragraph text indicates commands, file names,
directory names, paths, output, or returned values.
Example: The DK_Client package will not function unless the
wdreg_install batchfile is used.
italicWithin commands, italics indicate a variable that the user must
specify.
Example: mem_allocsize_in_bytes
Titles of manuals or other published documents are also set in
italics.
Notices
Courier
[ ]Within commands, items enclosed in square brackets are optional
{ }Within commands, items enclosed in braces are options from
|Within commands, the vertical bar separates options.
…An ellipsis indicates a repetition of the preceding parameter.
>The right angle bracket separates successive menu selections.
The Courier font indicates output or display.
Example:
parameters or values that the user can choose to specify or omit.
which the user must choose.
Example: Start > Programs > DK > wdreg_install.
Error: Unable to allocate memory for transfer!
NOTE: This messag e de notes n eutral or positive inf ormati on that cal ls out importan t
points to the text. A note provides information that may apply only in special cases.
CAUTION: Cautions call special attention to hazards that can cause system damage or data corruption,
to a lesser degree than warnings.
WARNING: Warnings call special attention to hazards that can cause system damage, data corruption,
personal injury, or death.
Atheros Communications, Inc.•iii
COMPANY CONFI DENTIALMarch 2003•iii
Atheros Communications, Inc.List of Tables•ix
COMPANY CONFI DENTIALMarch 2003 •ix
O
D
Y
P
O
C
T
O
N
x •AP User’s GuideAtheros Communications, Inc.
x•March 2003COMP AN Y CON FIDENTIAL
Preface
The intent of this document is to familiarize users with the Atheros AR5BAP00031 Access Point (AP), its setup, configuration, and usage. After reading
this user's guide, the user should be able to install, configure, control, and
maintain the Atheros Access Point.
About this Document
The document consists of the following chapters and appendices:
Chapter 1Introduction—Describes the Access Point package contents
Chapter 2AP Network Attachment and Configuration—Describes the
Appendix AAP Web Server—Describes the use of the web server to
Appendix B Regulatory Compliance Information—Important user
N
O
D
Y
P
O
and system requirements.
C
Access Point network connections and initial software
configuration.
T
O
configure the Access Point.
information and instructions concerning operating this
device in accordance with National spectrum usage laws for
radio devices.
Atheros Communications, Inc.Preface •xi
COMPANY CONFI DENTIALMarch 2003 •xi
O
D
Y
P
O
C
T
O
N
xii•AP User’s GuideAtheros Communications, Inc .
xii •Mar ch 2003COMPANY CONFIDENTIAL
1
1
Introduction
The Atheros Access Point implements an IEEE 802.11b/g wireless LAN
(WLAN) AP or data-oriented Residential Gateway (RG) supporting up to 256
station associations. Rates of 6 to 54 Mbps are supported in standard IEEE
802.11g mode, up to 11 Mbps in 802.11b mode, and up to 108 Mbps in Atheros
Turbo Mode
System Requirements
The AP contains a small boot executive that allows the main operating system
software to be downloaded using the Ethernet port over an FTP connection.
The Operating system software can also reside in the Flash memory of the AP,
which allows booting without the need to download the operating system
from the host PC over an FTP connection. A configuration file is created in
Flash memory to store user-configurable parameters such as WEP keys. A
terminal or PC with an Ethernet connection is required to perform the initial
O
AP configuration. An FTP server is required for firmware update to the AP.
.
N
D
Use the AP Web Server for firmware updates. Refer to Appendix A,
“Firmware Update Configuration Window” for information on the web
server.
Y
P
O
C
T
O
Atheros Communications, Inc.Introduction•1-1
COMPANY CONFI DENTIALMarch 2003•1-1
1
Chapter
Y
O
D
P
O
C
T
O
N
1-2 •AP Use r’s GuideAtheros Communications, Inc .
1-2 •March 2003COMPANY CONFIDENTIAL
2
2
AP Network Attachment and
Configuration
Y
This section provides procedures for connecting and configuring the AP to a
Host PC (HPC). Configuration can be performed either from a web browser
accessing the built-in web server, or by entering command using the
command line interface (CLI). For detailed information on using the web
server, refer to “AP Web Server” in Appendix A. For detailed information on
using CLI, refer to “AP Command-Line Interface” in Appendix B. For
“Factory Default Settings” refer to Appendix B.
O
AP Network Connections
Connect the HPC to the AP using one of the following two methods:
N
O
■Use an Ethernet crossover cable (not supplied) to connect directly to the
D
Ethernet port of the HPC. For more information on Ethernet cables, see
Table 2-1.
■Use standard Ethernet cables (not supplied) to connect through a hub or
Ethernet switch.
See Figure 2-1 for an example of the AP to the HPC connections.
P
O
C
T
Follow these steps to establish the network connections:
1. Connect the AP Ethernet port to the HPC Ethernet card through the
Ethernet hub/switch or an Ethernet crossover cable.
Atheros Communications, Inc.AP Network Attachment and Co nfiguration•2-1
COMPANY CONFI DENTIALMarch 2003•2-1
2
Chapter
2. Connect the optional RS-232 port to the HPC serial port through a serial
cable. Refer to Appendix C for more information on the serial interface.
3. Plug in the provided power supply to the AP power supply connector.
Host PC
(HPC)
RS-232
Port
Ethernet Port
Serial Cable
Ethernet Cable
C
Ethernet
T
Hub/Switch
O
N
Figure 2-1. Access Point to HPC Connections
Atheros Access Point
(AP)
Optional
RS-232
Port
Ethernet
Port
Ethernet
Cable
P
O
Power
Y
Power
Supply
O
Network Configuration
D
Follow these steps to configure the HPC for AP network control:
1. From the HPC’s Start menu, choose Settings and open the Network and
Dial-up Connections dialog box.
2. Right-click on the Local Area Connection icon that belongs to the Ethernet
controller connected to the AP, and select Properties.
2-2 •AP Use r’s GuideAtheros Communications, Inc .
2-2 •March 2003COMPANY CONFIDENTIAL
Chapter
3. Within the Local Area Connection Properties dialog box, choose Internet
Protocol (TCP/IP) and click Properties.
2
Y
O
D
P
O
C
T
O
N
Atheros Communications, Inc.AP Network Attachment and Co nfiguration•2-3
COMPANY CONFI DENTIALMarch 2003•2-3
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.