IL-80 ATEX LED
USER
INSTRUCTIONS
The Finnish MICA series rechargeable lamps are efcient and reliable tools.
To get the best benet from your lamp, read these user instructions before using the product. Use of
the Mica product must be controlled and accepted by the operator. Personnel using the Mica product
must be authorised by the operator or a designated representative. The operator is responsible for
the correct use and maintenance of the product. Repair of the Mica product must be carried out by a
competent party that is authorised by the manufacturer.
CLASSIFICATION:
Make sure that the classication of the lamp matches the zone classication of the area before using
the lamp!
BEFORE USE:
The lamp must be charged before use. The battery of the lamp reaches its full capacity after
approximately ten recharge and discharge cycles. Recharging must be done using a compatible MICA
charger that must be installed outside the explosion hazard area. Recharge time from empty battery to
full is approximately 6 hours. We recommend storing the lamp in its charging holder at all times. Also
read the manual of the charger.
Manufacturer: ATEXOR OY
P.O.Box 89, FIN-60101 SEINÄJOKI
Tel: +358-207 343 250
Internet: www.atexor.com
MICA IL-80 ATEX LED User instructions
OPERATION:
The lamp has a three-way operating switch (partial power/full power/OFF).
Note! In the IL-80 ATEX LED EM safety lamp model, the order is: full power/partial power/OFF.
The operating time depends on the lighting power selected. When approximately 1–2 hours of operating
time is remaining (depending on the temperature and the condition of the battery), the lamp starts to blink
approximately every 15 seconds. When the battery is running low, the control electronics switch off the lamp
automatically well in time before there is any danger of deep discharge. In special circumstances, the lamp can
be switched back on after the battery is empty to get light for a short while. This should be avoided, however,
as it shortens the life of the battery.
If the lamp is only used briey between recharge cycles, it is recommended that the battery be let run empty
by keeping the lamp on after every ten uses, for example.
Safety light operation (EM):
The IL-80 ATEX LED EM also has a safety lamp function: When kept in the charger stand, the lamp is continuously in standby mode and the LED light glows dimly. The lamp switches to full power when mains voltage is
not available.
MAINTENANCE:
The user may replace components which areavailable as spare parts. Repairing, amending and adjusting the
electronics card is absolutely forbidden!
The operating time of the lamp shortens as the battery ages. If the overall operating time is so short after
recharging that it disrupts the use of the lamp, the battery must be replaced. Only spare batteries supplied by
the manufacturer may be used for the lamp.
The lamp must be disassembled at least partially for all maintenance operations. To disassemble the lamp,
follow these instructions:
1: Turn the closing ring open and remove the glass lens. Turn the closing ring of the LED lamp until it opens
and remove the bulb using a clean cloth. Screw the support sleeve open using a wide straight screwdriver and
remove the reector.
2: The LED bulb and the reector must be handled with care as impurities reduce the luminosity. If the reector
or the LED bulb become dirty, they must be cleaned using a solvent.
3: Remove the exterior screws of the charging contacts and detach the charging contacts to remove the carrier
unit from the enclosure. If the carrier unit is tight, knock the lamp lightly against the edge of the table.
Pull the carrier unit halfway out of the enclosure and remove the operating switch connector (yellow wires). Pull
the carrier unit completely out of the enclosure.
4: Removal of the switch: Start by opening the four screws of the cover plate. Remove the coupler cover plate
and rubber cover. Then remove the coupler from the inside of the enclosure. NOTE! Also check that the rubber
cover is unbroken.
Note during assembly: Assemble the lamp in reverse order.
1: The closing ring of the LED lamp should be tightened well.
2: Tighten the closing ring well so that the arrow in the enclosure points to the mark in the closing ring.
(if necessary, you can lubricate the threads with mineral oil,
for example). See “Pic 1”.
Resetting the short-circuit protection:
After the LED bulb has been replaced, it may be necessary to reset the short-circuit protection of
electronics by keeping the lamp in the charger stand for a while. Resetting should also be done when
larger components have been replaced.
Note that the EX classication of the MICA IL-80 ATEX LED lamp requires that only original MICA
spare parts are used with the lamp. The L200Ex bulb of the MICA IL-80 ATEX LED lamp may not
be replaced with other bulbs. You can inuence the shape of the light beam by selecting a narrow or
medium-width reector.
NOTE! Always indicate the type and serial number of the lamp/charger when ordering spare parts!
MICA IL-80 ATEX LED SPARE PART NUMBERS:
1 M02912_X IL-80 LED battery pack
2 M03464_X IL-80 electronics unit (circuit board, carrier unit)
M03463_X IL-80 EM electronics unit (circuit board, carrier unit)
Note: When replacing electronic units,
the old unit must be returned to the manufacturer!
3 M00957 Charger contact unit (ILC4)
4 M03356 IL-80 ATEX LED lamp switch
5 M00419 IL switch rubber cover
6 MH0303_1 IL Ex switch cover plate unit
7 MH0307_1 IL reector, narrow
8 MH0304_1 L200Ex LED bulb unit
9 M00945 O ring
10 M01297_X IL glass lens
11 M0104_4 IL-80 ATEX LED closing ring
70706 IL-80 ATEX strap
OPERATING TIMES:
Partial power: 21 h
Full power: 10 h 30 min
11
10
6
4
5
9
1
2
8
7
3
MICA IL-80 ATEX LED
Classication II 2G Ex eib op is IIC T4 Gb
II 2D Ex tb IIIC T135°C Db
IP rating: IP67
Certicate: VTT 12 ATEX 004X Issue 1
Lamp designed and manufactured according to the European standards
EN 60079-0, EN 60079-7, EN 60079-11, EN 60079-28 and EN 60079-31.
MICA IL-80 ATEX LED SAFETY INSTRUCTIONS:
Before using the lamp:
- Cleaning and other preparations must always be carried out before moving to the explosion hazard
area.
- The charger must be installed outside the explosion hazard area. Recharging the lamp in the explosion
hazard area is not allowed.
Using the lamp:
- Check that the classication of the explosion hazard area matches the classication of the lamp. Do
not use the lamp in areas where it is not intended to be used!
- The lamp may not be opened in the explosion hazard area.
- If the lamp malfunctions, leave the explosion hazard area.
- If the machine plate cannot be read or is missing, the lamp may not be used in the explosion hazard
area.
- No labels or other additional parts may be attached to the lamp.
Maintenance of the lamp:
- Only a technician with electrical qualications may carry out maintenance on the lamp.
- Maintenance is carried out outside the explosion hazard area.
- Only original MICA spare parts may be used.
Manual_IL-80_LED_ENGL_9-2013
TECHNICAL DATA:
Battery NiMH 6V
Glass lens 110.5 x 5 mm
Reector narrow or medium width
Operating temperature –20°C...+40°C
Ingress protection IP-67
Weight 1.1 kg
Light source MICA L200Ex LED
Compatible charger: MICA ILC4 series chargers
TERMS AND CONDITIONS OF GUARANTEE:
A two-year guarantee from the purchase date is granted for the MICA IL-80 lamp, covering any manufacturing and material defects according to generally applicable terms and conditions of guarantee.
Please note that the guarantee period for the battery is one year. The guarantee becomes void if the
adjustment values of the electronics components have been changed or if any components have been
harmed in any other way. For maintenance repair, please send the lamp and the charger stand as well
as the purchase receipt with the product. Note! A new MICA lamp/battery must be taken into use or
recharged within three (3) months of manufacture.
© 09-2013 ATEXOR OY
We reserve the right to make changes to these
user instructions without advance notice.
Loading...