VM7824 / VM8824
4-Port True 4K HDMI Input Board / Output Board Quick Start Guide
Package Contents
1 VM7824 4-Port True 4K HDMI Input Board or VM8824 4-Port True 4K HDMI Output Board
4 Terminal Blocks
1 User Instructions
VM7824 Front View VM8824 Front View
1 2
4 5
1 2
4 5
1 2
4 5
1 2
4 5
3
1 2
1 2
4 5
4 5
Hardware Review
VM7824 Panel View
1. Link LEDs
2. ATEN LockPro™ Screws
3. Status LED
4. HDMI Input Ports
5. Audio Input Ports
VM8824 Panel View
1. Link LEDs
2. ATEN LockPro™ Screws
3. Status LED
4. HDMI Output Ports
5. Audio Output Ports
Hardware Setup
I/O Board Installation
Follow the steps below to safely install the VM7824 / VM8824 to a supporting
Modular Matrix Switch. For a list of the supported Modular Matrix Switch, visit
the VM7824/VM8824 product web pages.
Note: The VM3250 is used as an example in the instructions below.
1. Power off the Modular Matrix Switch.
Note: The VM7824/VM8824 cards are hot-swappable.
2. On the rear of the Modular Matrix Switch, unscrew the Phillips head screws
for one input slot (right) and one output slot (left), and then remove back
panel covers.
3. Slide the VM7824 into the input board slot, and the VM8824 into the output
slot. Make sure they secure in place.
1 2
1 2
4 5
4 5
1 2
1 2
Output Slots
4 5
4 5
Input Slots
1 2
1 2
4 5
4 5
3
3
VM7824 VM8824
4. Tighten the screws to secure the input and output boards to the
Modular Matrix Switch.
5. To install more I/O boards, repeat steps 2 to 4.
6. Proceed to the next section to install sources and displays.
Source and Display Device Installation
2
5
3
1
4
1. Connect one or more AV source devices to the HDMI and Audio Input ports of the VM7824.
2. Connect one or more display devices to the HDMI Output ports of the VM8824.
3. Connect one or more speakers or audio output devices to the Audio Output ports of the VM8824.
4. Make sure to ground the Modular Matrix Switch and all the devices in the installation.
5. Power on the Modular Matrix Switch and all the devices in the installation.
Support and Documentation
Notice
All information, documentation,
fi rmware, software utilities, and
specifi cations contained in this
package are subject to change
without prior notifi cation by
the manufacturer.
To reduce the environmental
impact of our products, ATEN
documentation and software can
be found online at
http://www.aten.com/
download/
Technical Support
www.aten.com/support
Scan for
more information
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifi cations not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
Warning: Operation of this equipment in a residential environment could cause radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시
기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
© Copyright 2019 ATEN® International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other trademarks
are the property of their respective owners.
This product is RoHS compliant.
Loading...