Aten VE2812UST, VE2812EUT User Manual

VE2812UST / VE2812EUT

HDMI & VGA HDBaseT Transmitter

with US / EU Wall Plate

User Manual

www.aten.com

VE2812UST / VE2812EUT User Manual

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

CE Warning: Operation of this equipment in a residential environment could

cause radio interference.

This device complies with Part 15 of the FCC Rules. O peration is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

Suggestion: Shielded twisted pair (STP) cables must be used with the unit to

ensure compliance with FCC & CE standards.

Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen verursachen.

KCC Statement

RoHS

This product is RoHS compliant.

VE2812UST / VE2812EUT User Manual

User Information

Online Registration

Be sure to register your product at our online support center:

International http://eservice.aten.com

Telephone Support

For telephone support, call this number:

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1- 949-42 8-1111

User Notice

All information, documentation, and specifications contained in this manual are

subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of the

manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior to

operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT

BEFORE USE.

iii

VE2812UST / VE2812EUT User Manual

Package Contents

1 VE2812UST / VE2812EUT HDMI & VGA HDBaseT Transmitter

1 3-Pin RS-232 Terminal Block

1 2-Pin Power Terminal Block

1 Mounting Kit (VE2812EUT only)

1 Faceplate (VE2812UST only)

1 Power Adapter

1 User Instructions

Note: Make sure that all of the components are present and in good

order. If anything is missing or was damaged in shipping, contact your dealer.

VE2812UST / VE2812EUT User Manual

EMC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

RoHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii

Product Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

1. Introduction

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Compatible ATEN Video Extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Side View 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Side View 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

LED Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2. Hardware Setup

Mounting the VE2812UST / VE2812EUT Unit . . . . . . . . . . . . . . . . . . . . . . 7

Site Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Drawing Screw Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

VE2812UST Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

VE2812EUT Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Optional Mounting Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the VE2812UST / VE2812EUT Unit. . . . . . . . . . . . . . . . . . . . 13

Terminal Block Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power Supply Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

RS-232 Channel Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

3. Operation

Selecting the Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Input Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Input Selection Pushbutton . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

RS-232 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Long Reach Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

VE2812UST / VE2812EUT User Manual

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Supported VGA Resolutions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Template Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

VE2812UST / VE2812EUT User Manual

About this Manual

This user manual is provided to help you get the most from the VE2812UST /

VE2812EUT unit. It covers all aspects of installation, configuration, and

operation. An overview of the information found in the manual is provided below.

Chapter 1, Introduction introduces you to the HDMI & VGA HDBaseT

Transmitter. Its purpose, features, installation considerations, and panel

components are presented and described.

Chapter 2, Hardware Setup describes the steps that are necessary to quickly

and safely set up your installation.

Chapter 3, Operation explains the Long Reach Mode and limitations, and how

to set up the input detection mode using the a pushbutton and RS-232

commands.

An Appendix provides a list of safety instructions and precautions, contact

information for ATEN technical support, product specifications, and other

technical information.

Note:



Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit or any connected

devices.



ATEN regularly updates its product documentation for new features and

fixes. For an up-to-date VE2812UST / VE2812EUT documentation, visit

......................... http://www.aten.com/global/en/

vii

VE2812UST / VE2812EUT User Manual

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start open the Start menu, and then select Run.

Indicates critical information.

→

Run means to

viii

VE2812UST / VE2812EUT User Manual

Product Information

For information about all ATEN products and how they can help you connect

without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller.

Visit ATEN on the Web for a list of locations and telephone numbers:

International http://www.aten.com

North America http://www.aten-usa.com

VE2812UST / VE2812EUT User Manual

This Page Intentionally Left Blank

Chapter 1

Introduction

Overview

ATEN VE2812UST / VE2812EUT is a video transmitter that can send V GA (wi th audio) and HDMI signals up to 100 m over a single Cat 5e/6/6a or ATEN 2L2910 Cat 6 cable. The VE2812UST / VE2812EUT guarantees reliable transmission of HDMI signals, supporting 3D, Deep Color, and embedded HD lossless audio formats. In addition, the VE2812UST / VE2812EUT supports Long Reach Mode, which allows the device to transmit signals up to 150 m, 1080p, over a Cat 5e/6 cable.

The VE2812UST / VE2812EUT can also function as a video switch by connecting to two sources and outputting them to the same format. The VE2812UST / VE2812EUT is designed for use in meeting rooms or digital education environments where high video quality is required.

VE2812UST / VE2812EUT User Manual

Features



Extends HDMI or VGA signals over a single Cat 5e/6/6a cable



HDMI (3D, Deep Color, 4K); HDCP compatible



Superior video quality



HDMI 4K up to 100 m via a Cat 5e/6/6a cable or ATEN 2L-2910 Cat 6 cable



VGA 1600 x 1200 / 1920 x 1200 up to 100 m via a Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable



Supports HDBaseT Long Reach Mode – extends signals up to 150 m, 1080p via a single Cat 5e/6 cable



Supports Auto Switch – the VE2812UST / VE2812EUT automatically switches to a newly plugged-in source



Functions as a switch and a converter



A switch: Connects to two source devices (HDMI or VGA)



A converter: Applies to receivers with different interfaces (DVI, DisplayPort, or HDMI)



Supports RS-232 channel transmission and source switch control



Compatible receivers – VE1812R, VE811R, VE814AR, VE801R, VE802R, VE601R, VE901R, or future ATEN HDBaseT Receivers



Supports IR signal frequencies from 30 kHz to 60 kHz



Plug-and-play with no required software



Built-in 8KV / 15KV ESD protection

Chapter 1. Introduction

Planning the Installation

Requirements

Prepare the following before installing the VE2812UST / VE2812EUT unit:



1 HDMI and/or VGA source device



1 Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable

Considerations



To ensure video quality, ATEN recommends using a Cat 5e/6/6a cable.

Note: ATEN recommends using the ATEN 2L-2910 Cat 6 cable for best

results.



The maximum transmission distance varies at different parts of the transmission:

Connection Interface Distance

Computer to the VE2812UST

/ VE2812EUT

The VE2812UST /

VE2812EUT to a compatible

ATEN Video Extender

A compatible ATEN Video

Extender to the display

HDMI 1.8 m

Cat 5e/6/6a 100 m / 150 m (up to 1080p in Long

Reach Mode)

HDMI 5 m

Compatible ATEN Video Extenders

The VE2812UST / VE2812EUT is compatible with the following ATEN

HDBaseT Video Extenders:



VE1812R



VE811R



VE814AR



VE601R



VE801R/802R

VE2812UST / VE2812EUT User Manual



VE901R



Future ATEN HDBaseT receivers

Components

Front View

No. Component Description

1 IR Port Connects to an IR transmitter/receiver.

2 HDMI In Connects to the HDMI Out port on the source device.

3 Audio In Connects to the Audio Out port on the source device.

4 VGA In Connects to the VGA Out port on the source device.

5 Input Switch

Pushbutton

Press to switch among the Auto Switch, HDMI, and VGA input mode. The input mode status is indicated by the three LEDs to the right of this pushbutton. For details, see LED Display, page 6.

Chapter 1. Introduction

Side View 1

No. Component Description

1 Firmware Upgrade Switch This port is reserved for ATEN Technical Support. If

you would like to do a firmware upgrade yourself, please contact your dealer.

2 HDBaseT Long Reach

Mode Switch

Put the switch to ON to enable the Long Reach Mode. For more details on Long Reach Mode, see Long Reach Mode, page 20.

Side View 2

No. Component Description

1 Power Jack Connects to the Power Adapter.

2 RS-232 Port Connects to an RS-232 main controller, such as a PC

or Control system.

3 HDBaseT Output Connects to the HDBaseT Output port on a

compatible ATEN video receiver via an RJ-45 cable.

+ 32 hidden pages

Aten VE2812UST, VE2812EUT User Manual

EMC Information

RoHS

User Information

Online Registration

Telephone Support

User Notice

Package Contents

Table of Contents

About this Manual

Conventions

Product Information

Overview

Features

Planning the Installation

Requirements

Considerations

Compatible ATEN Video Extenders

Components

Front View

Side View 1

Side View 2