ATEN VanCryst™
VE1901AEUT / VE1901AUST
DisplayPort HDBaseT-Lite Transmier
with EU / US Wall Plate / PoH
User Manual
VE1901AEUT / VE1901AUST User Manual
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
ge nerates , uses, and can radia te radio f requenc y energy a nd, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement
ii
VE1901AEUT / VE1901AUST User Manual
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
RoHS
This product is RoHS compliant.
iii
VE1901AEUT / VE1901AUST User Manual
About this Manual
This user manual is provided to help you get the most from the VE1901AEUT
/ VE1901AUST unit. It covers all aspects of installation, configuration, and
operation. An overview of the information found in the manual is provided
below.
Chapter 1, Introduction introduces you to the VE1901AEUT /
VE1901AUST DisplayPort HDBaseT-Lite Transmitter with EU / US Wall
Plate / PoH. Its purpose, features, installation considerations, and panel
components are presented and described.
Chapter 2, Hardware Setup describes the steps that are necessary to
quickly and safely set up your installation.
Chapter 3, Operation explains the Long Reach Mode and limitations, and
how to set up the input detection mode using the a pushbutton and RS-232
commands.
An Appendix provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information.
Note:
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit or any connected
devices.
ATEN regularly updates its product documentation for new features and
fixes. For an up-to-date VE1901AEUT / VE1901AUST documentation,
visit http://www.aten.com/global/en/
iv
VE1901AEUT / VE1901AUST User Manual
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦ Bullet lists provide information, but do not involve sequential steps.
>
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
open the Start menu, and then select Run.
Indicates critical information.
>
Run means to
v
VE1901AEUT / VE1901AUST User Manual
Package Contents
VE1901AEUT
1 VE1901AEUT DisplayPort HDBaseT-Lite Transmitter with EU Wall Plate
/ PoH
1 5-pin terminal block
1 rubber pad set (4 pcs)
1 faceplate
2 pan head screws
4 PF screws
1 power adapter
1 user instructions*
VE1901AUST
1 VE1901AUST DisplayPort HDBaseT-Lite Transmitter with US Wall Plate /
PoH
1 5-pin terminal block
1 faceplate
2 flat head screws
1 power adapter
1 user instructions*
Note: Make sure that all of the components are present and in good order. If
anything is missing or was damaged in shipping, contact your dealer.
vi
VE1901AEUT / VE1901AUST User Manual
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the W eb for a list of locations and telephone numbers:
International http://www.aten.com
North America http://www.aten-usa.com
User Information
Online Registration
Be sure to register your product at our online support center:
International http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1- 949-428-1111
vii
VE1901AEUT / VE1901AUST User Manual
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
viii
VE1901AEUT / VE1901AUST User Manual
Table of Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .viii
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Compatible ATEN Video Extenders . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. Hardware Setup
Mounting the VE1901AEUT / VE1901AUST Unit . . . . . . . . . . . . . . . . . . . . 9
Site Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Drawing Screw Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VE1901AEUT Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
VE1901AUST Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting the VE1901AEUT / VE1901AUST Unit . . . . . . . . . . . . . . . . .12
Terminal Block Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power Supply Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
RS-232 Channel Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. Operation
RS-232 Serial Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Bypass. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Connecting the Unit with VP1421 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appendix
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
ix
VE1901AEUT / VE1901AUST User Manual
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Template Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
x
Chapter 1
Introduction
Overview
The ATEN VE1901AEUT / VE1901AUST DisplayPort HDBaseT-Lite
transmitter delivers 4K signals up to 40 m over a single Cat 5e/6/6a or ATEN
2L-2910 Cat 6 cable, ensuring users to stabilize DisplayPort signal
transmission with support of Deep color and embedded HD lossless audio
formats. During high-quality video transmission, the transmitter can resist
signal interference with the equipped HDBaseT Anti-jamming technology and
offer a reliable signal extension.
The VE1901AEUT / VE1901AUST can be easily mounted in a 1-gang
junction box with EU / US wall plate, concealing bulky cable setups and
presenting needed information in sight. In addition, with built-in PoH (Power
over HDBaseT) function, the VE1901AEUT / VE1901AUST receives power
supply from a connected PoH PSE supported receiver and streamlines complex
power line deployment.
With the share function, the VE1901AEUT / VE1901AUST can remotely
switch source when connecting to a compatible receiver, e.g., VP1421,
bringing users for more convenient AV extension. This compact transmitter
provides a neat and simple installation on walls or tables, enabling users to
elegantly immerse their AV applications into any environment. Therefore, the
VE1901AEUT / VE1901AUST is ideal for use in meeting rooms, digital
educational environments or any application requiring stable high-quality
transmission and effortless installation.
RS
1
VE1901AEUT / VE1901AUST User Manual
Features
Extends DisplayPort signals with superior video quality over a single Cat
5e/6/6a cable or ATEN 2L-2910 Cat 6 cable
4K up to 40 m
1080p up to 70 m
Built-in PoH (Power over HDBaseT) function – the VE1901AEUT /
VE1901AUST receives power supply from the HDBasT output port
DisplayPort (Deep color, 4K); HDCP compliant
Designed to mount in a 1-gang junction box with EU / US wall plate
Supports RS-232 channel transmission
HDBaseT Anti-jamming – resists signal interference during high-quality
video transmission using HDBaseT technology
Share function – the VE1901AEUT / VE1901AUST can remotely switch
source when connecting to a compatible receiver, e.g., VP1421
LED indication of device status
Built-in 8KV / 15KV ESD protection
DC jack and PoH for power redundancy
Plug-and-play
2
Chapter 1. Introduction
Planning the Installation
Requirements
Prepare the following before installing the VE1901AEUT / VE1901AUST
unit:
1 DisplayPort source device
1 Cat 5e/6/6a or ATEN 2L-2910 Cat 6 cable
Considerations
To ensure video quality, ATEN recommends using a Cat 5e/6/6a cable.
Note: ATEN recommends using the ATEN 2L-2910 Cat 6 cable for best
results.
The maximum transmission distance varies at different parts of the
transmission:
Connection Interface Resolution Distance
Computer to the
VE1901AEUT / VE1901AUST
The VE1901AEUT /
VE1901AUST to a compatible
ATEN HDBaseT Receiver
A compatible ATEN Video
Receiver to the display
DisplayPort 4K 3 m
Cat 5e/6 4K 35 m
Cat 6a 4K 40 m
DisplayPort
(example)
4K 3 m
Note: The maximum transmission distance for 1080p resolution using an
ATEN 2L-2910 cable is 70 m.
Compatible ATEN Video Extenders
The VE1901AEUT / VE1901AUST is compatible with a wide range of ATEN
HDBaseT video receivers. Visit our official web site for more details.
3
VE1901AEUT / VE1901AUST User Manual
1
2
3
4
1
2
3
4
VE1901AEUT VE1901AUST
Components
Front View
No. LED Indication Description
1 power LED Lights green The unit is receiving power.
2 link LED Lights orange The transmission to the receiver is stable.
Blinks orange The transmission to the receiver is unstable.
3 share pushbutton N/A Press this pushbutton to share source with
the VP1421 (example). For details, see
Connecting the Unit with VP1421, page 18.
4 DisplayPort input
port
Note:
The power and link LED blink at the same time to indicate that the
firmware upgrade is in progress.
N/A Connects to the DisplayPort out port on the
source device.
4
Loading...