ATEN VE0801HB User manual

ATEN VanCryst™

VE0801HB

8-Port True 4K HDMI Switch
User Manual

VS0801HB User Manual

Compliance Statements

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT

This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not inst alle d and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC Caution

Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.

Warning

Operation of this equipment in a residential environment could cause radio
interference.

Achtung

Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.

KCC Statement

ii

VS0801HB User Manual

Industry Canada Statement

This Class A digital apparatus complies with Canadian ICES-003.

HDMI Trademark Statement

The terms HDMI, HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.

RoHS

This product is RoHS compliant.

iii

VS0801HB User Manual

About this Manual

This user manual is provided to help you get the most from the VS0801HB. It

covers all aspects of installation, configuration, and operation. An overview of

the information found in the manual is provided below.

Chapter 1, Introduction

introduces you to the 8-Port True 4K HDMI Switch.
Its purpose, features, and installation considerations are described and
discussed.

Chapter 2, Hardware Setup

describes the panel components and the steps

to quickly and safely set up the VS0801HB.

Chapter 3, Operation

provides details on how to operate and configure the
VS0801HB using the panel pushbuttons, IR remote control unit, and RS-232
commands.

Chapter 4, The Firmware Upgrade Utility

explains how to download the

VS0801HB’s firmware and upgrade the device using the utility.

An Appendix provides a list of safety instructions and precautions, contact

information for ATEN technical support, product specifications, and other

technical information.

Note:

 Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the unit or any connected

devices.

 ATEN regularly updates its product documentation for new features and

fixes. For an up-to-date VS0801HB documentation, visit

http://www.aten.com/global/en/

iv

Conventions

This manual uses the following conventions:

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means to

press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential steps.

> Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start
open the Start menu, and then select Run.

Indicates critical information.

VS0801HB User Manual

>

Run means to

v

VS0801HB User Manual

Package Contents

 1 VS0801HB 8-Port True 4K HDMI Switch

 1 IR remote control unit

 1 IR receiver

 1 power adapter

 1 rack mount kit

 1 user instructions

Note: Make sure that all of the components are present and in good order. If

anything is missing or was damaged in shipping, contact your dealer.

vi

VS0801HB User Manual

Product Information

For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:

International http://www.aten.com

North America http://www.aten-usa.com

User Information

Online Registration

Be sure to register your product at our online support center:

International http://eservice.aten.com

Telephone Support

For telephone support, call this number:

International 886-2-8692-6959

China 86-400-810-0-810

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

1- 949-42 8-1111

vii

VS0801HB User Manual

User Notice

All information, documentation, and specifications contained in this manual

are subject to change without prior notification by the manufacturer. The

manufacturer makes no representations or warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims any

warranties as to merchantability or fitness for any particular purpose. Any of

the manufacturer's software described in this manual is sold or licensed as is.

Should the programs prove defective following their purchase, the buyer (and

not the manufacturer, its distributor, or its dealer), assumes the entire cost of all

necessary servicing, repair and any incidental or consequential damages

resulting from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV

interference caused by unauthorized modifications to this device. It is the

responsibility of the user to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation

of this system if the correct operational voltage setting was not selected prior

to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS

CORRECT BEFORE USE.

viii

VS0801HB User Manual

Table of Contents

Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii

1. Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Required Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Optional Equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2. Hardware Setup

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

IR Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. Operation

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Switching the Display Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Setting the Switch Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Enabling/Disabling the Next Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Enabling/Disabling the Priority and the POD Mode . . . . . . . . . . . . . . 13

Enabling/Disabling the Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Executing an RS-232 Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Restarting the VS0801HB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4. The Firmware Upgrade Utility

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Appendix

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ix

VS0801HB User Manual

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

x

Chapter 1

Introduction

Overview

The ATEN VS0801HB is designed for applications that require routing of 8

sources to one compatible display device. The VS0801HB supports video

resolutions up to true 4K (4096 x 2160 @ 60Hz 4:4:4), data rates up to 18

Gbps, 3D, Deep Color up to 12-bit, and HD lossless audio formats. The

VS0801HB features different switch modes for automatic port selection and

multiple control options (panel pushbuttons, RS-232 commands, IR remote

control unit) are available to conveniently operate the unit, allowing for easy

integration.

Engineered to meet today’s demand of true 4K signal transmission and

user-oriented design, the ATEN VS0801HB is a powerful solution for

a wide range of settings, such as home theater, meeting rooms, trade

shows, and shopping centers.

1

Chapter 1. Introduction

Features

 Allows up to 8 HDMI sources to be connected to one HDMI display

 HDMI (3D, Deep Color, 4K); HDCP 2.2 compliant

 Superior video quality – True 4K resolutions of 4K x 2K @ 60 Hz (4:4:4)

and standard 1080p (1920 x 1080 @ 60 Hz)

 Built-in bi-directional RS-232 serial port for high-end system control

 Switch modes for automatic port selection

 Supports IR extension

 Clear LED indication of device status

 Plug-and-play

 Rack Mountable

2