ATEN VanCryst™
VC882
True 4K HDMI Repeater with Audio
Embedder and De-Embedder
User Manual
VC882 User Manual
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not inst alle d and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement
ii
VC882 User Manual
HDMI Trademark Statement
The terms HDMI, HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing
Administrator, Inc.
RoHS
This product is RoHS compliant.
iii
VC882 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International http://eservice.aten.com
Telephone Support
For telephone support, call this number:
International 886-2-8692-6959
China 86-400-810-0-810
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
1-949-428-1111
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iv
VC882 User Manual
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
International http://www.aten.com
North America http://www.aten-usa.com
v
VC882 User Manual
Package Contents
Check to make sure that all the components are in working order. If you
encounter any problem, please contact your dealer.
1 VC882 True 4K HDMI Repeater with Audio Embedder and De-
Embedder
1 3-pin terminal block
1 power adapter
1 user instructions
vi
VC882 User Manual
Table of Contents
Compliance Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vi
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x
1. Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Planning the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Hardware Setup
Connecting the VC882 Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Operation
Audio Embedder Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mode 1 PIN 1 Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mode 2 PIN 2 Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Audio Extractor Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mode 2 PIN 1 Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mode 2 PIN 2 Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mode 3 PIN 3 and PIN 4 Switch Operation. . . . . . . . . . . . . . . . . . . . . 10
4. The Firmware Upgrade Utility
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Downloading the Firmware Upgrade Package . . . . . . . . . . . . . . . . . . 11
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Starting the Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Upgrade Succeeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Upgrade Failed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Firmware Upgrade Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix
vii
VC882 User Manual
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
viii
VC882 User Manual
About this Manual
This user manual is provided to help you get the most from the VC882 unit. It
covers all aspects of installation, configuration, and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction introduces you to the True 4K HDMI Repeater
with Audio Embedder and De-Embedder. Its purpose, features, installation
considerations, and panel components are presented and described.
Chapter 2, Hardware Setup describes the steps that are necessary to
quickly and safely set up your installation.
Chapter 3, Operation explains the source input operation using the source
switch pushbutton and RS-232 commands and its limitations.
Chapter 4, The Firmware Upgrade Utility explains the source input
operation using the source switch pushbutton and RS-232 commands and its
limitations.
Appendix, provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information.
Note:
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit or any connected
devices.
This product may be updated with features and functions added, improved
or removed since the release of this manual. For an up-to-date user
manual, visit
http://www.aten.com/global/en/
ix
VC882 User Manual
Conventions
This manual uses the following conventions:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
♦ Bullet lists provide information, but do not involve sequential steps.
> Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
open the Start menu, and then select Run.
Indicates critical information.
>
Run means to
x
Chapter 1
Introduction
Overview
The VC882 is a True 4K HDMI Repeater with Audio Embedder and DeEmbedder capable of embedding or de-embedding the HDMI audio signal,
while supporting the HDMI signal transmission distance up to 5 meters with
True 4K resolution. Apart from embedding a separate audio to an outgoing
HDMI signal, the VC882 also allows audio extraction from the HDMI signal,
and outputs the extracted signal through an alternative audio system.
In terms of the audio aspect, the VC882 works with versatile pass-through of
HDMI audio formats LPCM2.0, Dolby Digital 2.0, Dolby Digital 5.1 and DTS
Digital 5.1. The VC882 also supports ARC function which eliminates the need
of bulky cable setups when connecting an AV receiver, or a home theater
system to a TV. When it comes to the video aspect, the VC882 supports True
4K (4096 x 2160 @ 60Hz 4:4:4) in HDR10, HDR10+, Dolby Vision and
Hybrid Log-Gamma (HLG) formats to provide staggeringly crisp images. It is
HDCP 2.2-compliant for content protection. The compact enclosure design,
True 4K signal transmission, and embedding / de-embedding capability have
made the VC882 ideal for training and conference rooms, video production,
and home theater installations.
1
Chapter 1. Introduction
Features
Embeds audio to the HDMI output or de-embeds audio from the HDMI
signal and outputs the extracted signal through an alternative audio system
Easy embedding / de-embedding mode selection via 2 / 4-pin DIP
switches
HDMI (3D, Deep Color, True 4K); HDCP 2.2 compliant
True 4K video quality — supports resolutions up to 4096 x 2160 @ 60Hz
(4:4:4)
Supports True 4K / HDR formats — HDR10, HDR10+, Dolby Vision and
Hybrid Log-Gamma (HLG)
Supports HDMI audio formats — LPCM 2.0, Dolby Digital 2.0, Dolby
Digital and DTS Digital 5.1 channels
Compact, portable metal enclosure designed for HDMI Lock-pro
Firmware upgradable
2
VC882 User Manual
Planning the Installation
Requirements
Prepare the following before installing the VC882 unit:
1 HDMI source device
1 HDMI display
2 HDMI cable
1 audio source device (e.g., audio mixer)
1 audio output device (e.g., audio amplifier)
2 RCA cable
2 3-pin terminal block
Considerations
The maximum transmission distance varies at different parts of the
transmission:
Connection Interface Distance
HDMI source to the VC882 HDMI 5 m
VC882 to the HDMI display HDMI 5 m
3
Chapter 1. Introduction
1
2
3
4
5
6
7
Components
Front View
No. Component Description
1 cable lock screw for
ATEN LockPro
2 audio out port
(coaxial)
3 audio out port (3-pin
terminal block)
4 audio extractor
switches (mode 2)
5 HDMI output port Connects to an HDMI-enabled display device.
6 firmware upgrade
port
7 power LED When LED lights green, it means the VC882 is receiving
Universal HDMI cable lock that provides the easiest way to
™
secure an HDMI cable to most HDMI devices.
Connects to an audio output device (e.g., speakers).
Connects to an audio output device (e.g., audio amplifier).
Sets PIN 1 switch to enable or disable audio extractor
function. See Mode 2 PIN 1 Switch Operation, page 10.
Sets PIN 2 switch to enable or disable ARC function. See
Mode 2 PIN 2 Switch Operation, page 10.
Set PIN 3 and PIN 4 switches to set EDID modes. See
Mode 3 PIN 3 and PIN 4 Switch Operation, page 10.
Connects to a USB Micro-B cable for firmware upgrades.
See The Firmware Upgrade Utility, page 11.
power.
4
VC882 User Manual
2
3
4
5
6
7
1
Rear View
No. Component Description
1 cable lock screw for
ATEN LockPro
2 power jack Connects to the power adapter.
3 reset button Press this reset button to reread signals every time
4 HDMI input port Connects to an HDMI source device.
5 audio embedder switches
(mode 1)
6 audio in port (3-pin
terminal block)
7 audio in port (coaxial) Connects to an audio input device.
™
Universal HDMI cable lock that provides the easiest
way to secure an HDMI cable to most HDMI devices.
you configure mode 1 and mode 2 switches, or
change AV inputs and outputs.
Sets PIN 1 switch to enable or disable audio
embedder function. See Mode 1 PIN 1 Switch
Operation, page 9.
Sets PIN 2 switch to set the audio embed source.
See Mode 2 PIN 2 Switch Operation, page 9.
Connects to an audio input device (e.g., audio mixer).
5
Chapter 1. Introduction
This Page Intentionally Left Blank
6
Chapter 2
1. Please review the safety information regarding the placement of
this device in Safety Instructions, page 17.
2. Do not power on the VC882 until all the necessary hardware is
connected.
5
1
3
Power HDMI Audio In
2
HDMI
4
Audio Out
Hardware Setup
Connecting the VC882 Unit
Follow the steps below to connect the VC882 to an HDMI source device, an
HDMI-enabled display device, an audio input device, and an audio output
device.
7
Chapter 2. Hardware Setup
1. Connect an HDMI video source to the unit’s HDMI input port. Optionally
secure the HDMI cable with the corresponding cable lock screw for ATEN
LockPro™.
2. Connect an HDMI display to the unit’s HDMI output port. Optionally
secure the HDMI cable with the corresponding cable lock screw for ATEN
LockPro™.
3. Connect an audio mixer to the unit's audio in ports using the 3-pin terminal
block provided. Optionally, use the audio embedder switches (mode 1) to
enable or disable audio embedding for the connected audio inputs.
4. Connect an audio amplifier or a set of speakers to the unit's audio out
ports. Optionally, use the audio extractor switches (mode 2) to enable or
disable audio extraction for the connected audio inputs.
5. Plug one end of the power adapter into the unit’s power jack, and the other
end to an AC power source. The power LED shall be lit in blue.
6. Power on all connected equipment.
8
Chapter 3
audio embedder switches (mode 1)
Operation
Audio Embedder Switches
Sets the audio embedder switches (mode 1) to enable or disable the audio
embedder function, and set the audio embed source.
Note: Remember to press the reset button to reread signals every time you
configure mode 1 and mode 2 switches, or change AV inputs and
outputs.
Mode 1 PIN 1 Switch Operation
DPI Switch Position Description
PIN 1 ON ↓ Enables audio embedder function.
OFF↑ Disables audio embedder function.
Mode 2 PIN 2 Switch Operation
DPI Switch Position Description
PIN 2 ON ↓ Switches audio embedder to the audio in port
(coaxial).
OFF↑ Switches audio embedder to the audio in port (3-pin
terminal block).
9
Chapter 3. Operation
audio extractor switches (mode 2)
Audio Extractor Switches
Sets the audio extractor switches (mode 2) to enable or disable the audio
extractor and ARC functions, or set EDID modes.
Note: Remember to press the reset button to reread signals every time you
configure mode 1 and mode 2 switches, or change AV inputs and
outputs.
Mode 2 PIN 1 Switch Operation
DPI Switch Position Description
PIN 1 ON ↓ Enables audio extractor function via coaxial and 3-pin
terminal block.
OFF↑ Disables audio extractor function via coaxial and 3-pin
terminal block.
Mode 2 PIN 2 Switch Operation
DPI Switch Position Description
PIN 2 ON ↓ Enables ARC function.
OFF↑ Disables ARC function.
Mode 3 PIN 3 and PIN 4 Switch Operation
DPI Switch Position PIN 3 PIN 4 Description
PIN 3 + PIN 4 ON ↓ ON ↓ Sets to EDID Bypass Mode (default).
OFF↑ ON ↓ Sets to EDID 5.1 CH Mode.
ON ↓ OFF↑ Sets to EDID 2 CH Mode.
OFF↑ OFF↑ Sets to EDID Learn Mode.
10
Chapter 4
The Firmware Upgrade Utility
Introduction
The purpose of the Windows-based Firmware Upgrade Utility is to provide an
easy process for upgrading the VC882. The program comes as part of a
Firmware Upgrade Package that is specific for each device.
As new firmware versions become available, new firmware upgrade packages
are posted on our website. Check the website regularly to find the latest
information and packages.
Downloading the Firmware Upgrade Package
To download the firmware upgrade package:
1. On our Website go to: Download - Firmware and choose the device
model, or from the VC882 product page under the Resources tab, select
Firmware. A list of available firmware upgrade packages appears.
2. Choose the firmware upgrade package that you wish to install (usually the
most recent) and download it to your computer.
11
Chapter 4. The Firmware Upgrade Utility
Preparation
To prepare for the firmware upgrade, do the following:
1. Unplug the VC882’s power adapter.
2. Use a USB Micro-B cable to connect a USB Type-A port on your computer,
and the other end to the firmware upgrade port of your VC882.
3. Plug the power adapter into power jack on the VC882.
4. If successful, the power LED will start to flash. Now, you can start the
upgrade process as explained on the next page.
12
VC882 User Manual
Starting the Upgrade
To upgrade the firmware:
1. Run the downloaded firmware upgrade package file either by doubleclicking the file icon, or by opening a command line and entering the full
path to it.
The Firmware Upgrade Utility welcome screen appears:
Note: The screens shown in this section are for reference only. The wording
and layout of the actual screens put up by the Firmware Upgrade Utility
may very slight from these examples.
2. Read and Agree to the License Agreement (click the I Agree radio button).
13
Chapter 4. The Firmware Upgrade Utility
3. Click Next to continue. The Firmware Upgrade Utility main screen
appears. The devices capable of being upgraded are listed in the Device
List panel:
4. Click Next to perform the upgrade. The Status LEDs SDI, HDMI, and
power will flash while the upgrade is in process.
If you enabled Check Firmware Version, the Utility compares the device's
firmware level with that of the upgrade files. If it finds that the device's
version is higher than the upgrade version, it brings up a dialog box
informing you of the situation and gives you the option to continue or
cancel.
If you didn't enable Check Firmware Version, the Utility installs the
upgrade files without checking whether they are a higher level, or not.
Status messages appear in the Status Messages panel, and the progress
toward completion is shown on the Progress bar.
14
VC882 User Manual
Upgrade Succeeded
After the upgrade has completed, the power LED will stop flashing and a
screen appears to inform you that the procedure was successful:
Click Finish to close the Firmware Upgrade Utility.
Upgrade Failed
If the Upgrade Succeeded screen doesn't appear, it means that the upgrade
failed to complete successfully. See the next section, Firmware Upgrade
Recovery, for how to proceed.
15
Chapter 4. The Firmware Upgrade Utility
Firmware Upgrade Recovery
There are three conditions that call for firmware upgrade recovery:
When a firmware upgrade is manually aborted.
When the mainboard firmware upgrade fails.
When the I/O firmware upgrade fails.
To perform a firmware upgrade recovery, do the following:
1. Power off the device.
2. Connect the USB Micro-B cable to the USB Type-A port on your computer,
and the other end to the firmware upgrade port of your VC882
3. Repeat the upgrade procedure.
16
Appendix
Safety Instructions
General
This product is for indoor use only.
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If
the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for
adequate ventilation. To ensure reliable operation, and to protect against
overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as
this will block its ventilation openings. Likewise, the device should not be
placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid
or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on
the marking label. If you are not sure of the type of power available,
consult your dealer or local power company.
To prevent damage to your installation it is important that all devices are
properly grounded.
Do not allow anything to rest on the power cord or cables. Route the
power cord and cables so that they cannot be stepped on or tripped over.
Position system cables and power cables carefully; Be sure that nothing
rests on any cables.
Never push objects of any kind into or through cabinet slots. They may
touch dangerous voltage points or short out parts resulting in a risk of fire
or electrical shock.
17
Appendix
Do not attempt to service the device yourself. Refer all servicing to
qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet
and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need
for service.
The device does not operate normally when the operating instructions
are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will
require extensive work by a qualified technician to repair.
18
VC882 User Manual
Rack Mounting
Before working on the rack, make sure that the stabilizers are secured to
the rack, extended to the floor, and that the full weight of the rack rests on
the floor. Install front and side stabilizers on a single rack or front
stabilizers for joined multiple racks before working on the rack.
Always load the rack from the bottom up, and load the heaviest item in the
rack first.
Make sure that the rack is level and stable before extending a device from
the rack.
Use caution when pressing the device rail release latches and sliding a
device into or out of a rack; the slide rails can pinch your fingers.
After a device is inserted into the rack, carefully extend the rail into a
locking position, and then slide the device into the rack.
Do not overload the AC supply branch circuit that provides power to the
rack. The total rack load should not exceed 80 percent of the branch circuit
rating.
Make sure that all equipment used on the rack – including power strips and
other electrical connectors – is properly grounded.
Ensure that proper airflow is provided to devices in the rack.
Ensure that the operating ambient temperature of the rack environment
does not exceed the maximum ambient temperature specified for the
equipment by the manufacturer.
Do not step on or stand on any device when servicing other devices in a
rack.
19
Appendix
Technical Support
International
For online technical support – including troubleshooting, documentation,
and software updates: http://support.aten.com
For telephone support, see Telephone Support, page iv:
North America
Email Support support@aten-usa.com
Online Technical
Support
Telephone Support 1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase
Your computer configuration, including operating system, revision level,
expansion cards, and software
Any error messages displayed at the time the error occurred
The sequence of operations that led up to the error
Any other information you feel may be of help
Troubleshooting
Documentation
Software Updates
http://www.aten-usa.com/support
20
VC882 User Manual
Specifications
Function VC882
LED
Power 1 x LED (Blue)
Reset Button 1 x Pushbutton (to activate mode configuration)
Switches
Mode Selection 2 x Switches (Mode 1)
Video Input
Interfaces 1 x HDMI Type-A Female (Black)
Impedance 100 Ώ
Max. Distance 5 m
Video Output
Interfaces 1 x HDMI Type-A Female (Black)
Impedance 100Ώ
Max. Distance 5 m
Video
Max. Data Rate 18 Gpbs
Max. Pixel Clock 600 MHz
Compliance HDMI (3D, Deep Color)
Max. Resolutions 4096 x 2160 @ 60Hz (4:4:4) 8 bit
Audio
Output 1 x Coaxial
PIN 1 (Enables or disables audio embedder function)
PIN 2 (Sets the audio embed source)
4 x Switches (Mode 2)
PIN 1 (Enables or disables audio extractor function)
PIN 2 (Enables or disables ARC function)
PIN 3 & PIN 4 (Sets the EDID mode: Bypass, 5.1 CH, 2 CH,
Format: LPCM 2.0, Dolby Digital 2.0, Dolby Digital 5.1, and
Format: Analog, stereo, unbalanced, and LPCM 2.0
and Learn)
HDCP 2.2
DTS Digital 5.1
1 x 3-pin terminal block
21
Appendix
Function VC882
Input 1 x Coaxial
Format: LPCM 2.0, Dolby Digital 2.0, Dolby Digital 5.1, and
DTS Digital 5.1
1 x 3-pin terminal block
Format: Analog, stereo, unbalanced, and LPCM 2.0
Connectors
Power 1 x DC Jack, 5V 3A, Lockable
Firmware Upgrade 1 X USB Micro-B
Power
Consumption DC5V; 2.905W; 9.92BTU
Environmental
Operating Temperature 0 - 40°C
Storage Temperature -20 - 60°C
Humidity 0 - 80% RH, Non-Condensing
Physical Properties
Housing Metal
Weight 0.24 kg (0.53 lb)
Dimensions (L x W x H) 12.22 x 8.22 x 2.50 cm (4.81 x 3.24 x 0.98 in)
22
VC882 User Manual
Limited Warranty
ATEN warrants its hardware in the country of purchase against flaws in
materials and workmanship for a Warranty Period of two [2] years (warranty
period may vary in certain regions/countries) commencing on the date of
original purchase. This warranty period includes the LCD panel of ATEN LCD
KVM switches. Select products are warranted for an additional year (see A+
Warranty for further details). Cables and accessories are not covered by the
Standard Warranty.
What is covered by the Limited Hardware Warranty
ATEN will provide a repair service, without charge, during the Warranty
Period. If a product is detective, ATEN will, at its discretion, have the option
to (1) repair said product with new or repaired components, or (2) replace the
entire product with an identical product or with a similar product which fulfills
the same function as the defective product. Replaced products assume the
warranty of the original product for the remaining period or a period of 90 days,
whichever is longer. When the products or components are replaced, the
replacing articles shall become customer property and the replaced articles
shall become the property of ATEN.
To learn more about our warranty policies, please visit our website:
http://www.aten.com/global/en/legal/policies/warranty-policy/
© Copyright 2021 ATEN® International Co., Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners.
Released: 2021-12-13
23
Loading...