This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful inter ference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
KCC Statement
ii
RoHS
This product is RoHS compliant.
US3310 User Manual
iii
US3310 User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
Internationalhttp://eservice.aten.com
Telephone Support
For telephone support, call this number:
International886-2-8692-6959
China86-400-810-0-810
Japan81-3-5615-5811
Korea82-2-467-6789
North America1-888-999-ATEN ext 4988
1- 949-428 -1111
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
iv
US3310 User Manual
Package Contents
1 US3310 2-Port USB-C Gen 1 Dock Switch with Power Pass-through
2 USB-C Cables
1 Remote Port Selector
1 User Instructions
Note:Make sure that all of the components are present and in good order.
If anything is missing or was damaged in shipping, contact your dealer.
This user manual is provided to help you get the most from the US3310 unit. It
covers all aspects of installation, configuration, and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction introduces you to the 2-Port USB-C Gen 1 Dock
Switch with Power Pass-through. Its purpose, features, declaration, and panel
components are presented and described.
Chapter 2, Hardware Setup describes the steps that are necessary to quickly
and safely set up your installation.
Chapter 3, Operation explains the
Appendix provides a list of safety instructions and precautions, contact
information for ATEN technical support, product specifications, and other
technical information.
Note:
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit or any connected
devices.
ATEN regularly updates its product documentation for new features and
fixes. For an up-to-date US3310 documentation, visithttp://www.aten.com/
global/en/
port selection options.
vii
US3310 User Manual
Conventions
This manual uses the following conventions:
MonospacedIndicates text that you should key in.
[ ]Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1.Numbered lists represent procedures with sequential steps.
♦Bullet lists provide information, but do not involve sequential steps.
→Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
open the Start menu, and then select Run.
Indicates critical information.
Product Information
→
Run means to
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Internationalhttp://www.aten.com
North Americahttp://www.aten-usa.com
viii
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.