ATEN UC-210T User Manual

Remove the previously

installed network card (see

Preliminary Steps).

Switch must be manually

configured for half duplex

mode. See documentation

that came with the switch

Conflict with

previously installed

network card(s) and

software.

Unit operates in half

duplex mode. Older

switches may not

automatically detect

for details.

Disable the previously

installed network card

according to the

this.

Conflict with

previously installed

network card.

procedures given in the

Preliminary Steps section

of the Installation

instructions.

User Manual

UC-210T

Read this manual thoroughly and follow the installation and

operation procedures carefully to prevent any damage to the

unit, and/or any of the devices connected to it.

This package contains:

M 1 USB 2.0 to Ethernet Adapter

M 1 USB Cable

M 1 Driver Disk

M 1 User Manual

If anything is damaged or missing, contact your dealer.

Manual Part No. PAPE-1169-2AT

All brand names and trademarks are the registered property of their respective owners.

Printed in Taiwan 04/2003

- 5 -- 4 -

Problem Cause Action

Windows cannot

find driver on

Troubleshooting

Function Specification

installation disk.

Link and TX/RX (Green)

LAN RJ-45 Socket

Status

Unit does not

operate with

Ethernet switch.

Speed Red for 10Mbps; Green for 100 Mbps

Connot connect

with the network.

IEEE 802.3µ 100BaseTx

Storage Temp: -20 ~ 60

Humidity: 0 ~ 80% RH, Noncondensing

Limited Warranty

IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY

FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE

OF THE PRODUCT, DISK, OR ITS DOCUMENTATION

EXCEED THE PRICE PAID FOR THE PRODUCT.

The direct vendor makes no warranty or representation,

expressed, implied, or statutory with respect to the contents or

use of this documentation, and especially disclaims its quality,

performance, merchantability, or fitness for any particular

purpose.

The direct vendor also reserves the right to revise or update the

device or documentation without obligation to notify any

individual or entity of such revisions, or update. For further

inquiries, please contact your direct vendor.

Specifications

Connectors USB Type B Socket

LEDs

Data Transfer Rate Depends on USB rate

Network Protocol IEEE 802.3 10BaseT

Power Consumption 1W (max.)

Power Modes Bus Powered

Environment Operating Temp: 0 ~ 50

Housing Plastic

Weight 38

Dimensions (L x W x H) 6 x 4 x 2.36 cm

System Requirements

M Win98, 2000, Me, or XP

M USB 2.0 Host Controller installed on the system

a. Right click on My Computer

disconnected from the network, and that no other applications

are running.

Installation

Preliminary Steps

1. Before you begin, make sure that the UC-210T is

2. Disable any network interface card (NIC) currently installed

on your system:

b. Click on Properties

Disable in this hardware profile

c. Click on Device Manager

f. On the General page, in the Device Usage section, check

e. Find your adapter in the list and Double Click on it.

d. Click on the Plus sign next to Network adapters

g. Click on OK

sure to specify your floppy disk drive (drive A:)

the UC-210T to the computer’s USB port; The Add New

Hardware Wizard appears. Put the driver disk into your disk

drive, and Click Next.

installation.

Note: In the dialog box that asks where to find the driver, be

Windows Installation

1. Use the USB cable that came with this package to connect

2. Follow along with the dialog boxes to complete the

to inform you that the installation has finished. Click Finish.

3. After the driver files have been copied, a dialog box appears

restart the computer. Remove the driver disk; plug the LAN

4. In the dialog box that comes up, you are asked if you want to

Lan Cable

cable into the UC-210T’s RJ-45 socket; and Click Yes.

This completes the installation. If, for any reason, you disconnect

the UC-210T from the computer and then reconnect it, allow the

system up to two minutes (approximately), to recognize the

reconnected adapter.

- 2 -- 1 - - 3 -

Overview

The UC-210T is a 10BaseT/100BaseTx auto-sensing USB 2.0 to

Ethernet adapter that provides an external plug-and-play LAN

connection for PCs, notebooks, laptops, and handheld

computing devices that support the USB specification. The

UC-210T contains an RJ-45 socket for the Ethernet LAN cable

to plug into, and a USB type B port for a USB cable that

Note: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy, and if not installed and used in

connects to a PC’s USB port, or to a USB hub.

accordance with the instruction manual, may cause

The cable from the LAN plugs in here.

For further convenience - especially to users of notebooks,

laptops, and handhelds - the UC-210T USB 2.0 Ethernet

Adapter derives its operating power from the Universal Serial

Bus itself, so no bulky external power supply needs to be taken

along. And because it is a USB Specification 2.0 compliant

device, it supports fast data transfer rates of up to 480Mbps, and

energy-saving suspend and resume operations.

Components

ceiver;

from that which the receiver is connected;

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

M Reorient or relocate the receiving antenna;

M Increase the separation between the equipment and re-

M Connect the equipment into an outlet on a circuit different

nician for help.

M Consult the dealer or an experienced radio/television tech-

1. RJ-45 Socket

Features

M USB Interface Specification 2.0 Compliant

M IEEE 802.3 10BaseT

2. LEDs:

M IEEE 802.3µ 100BaseTx Ethernet Half Duplex

This LED lights when a link to the LAN has been estab-

M Link and Tx/Rx (Green)

M Plug and Play Installation with Automatic Configuration

M Win98/2000/Me/XP Driver Support

lished. It flashes when data is being transmitted between

the computer and the LAN

This dual colored LED lights Red when the transmission

M Transmission Speed

USB Hub

M Standard USB Cable Connection To USB Host Adapter or

M Standard RJ-45 Cable Connection to the LAN

speed is 10Mbps, and lights Green when the transmission

speed is 100Mbps

M LED Display for Easy Diagnostics

M Bus Powered - External Power Supply Not Required

The B end of the cable plugs into the UC-210T; the A end of

the cable plugs into the computer’s USB port (or a USB hub).

3. USB Cable

M Multi Megabit Burst Data Transfer Rates

M Data Communications Capability at LAN Speeds

M Supports Energy-Saving Suspend and Resume Functions