Package Contents
2
1
1 Power Distribution Unit
1 Power Cord
1 User Instructions
Hardware Review
A
1 2 3 4
6
Support and Documentation Notice
Rack Mounting
C
Rack
5
6
7
All information, documentation, fi rmware,
software utilities, and specifi cations
contained in this package are subject to
change without prior notifi cation by
the manufacturer.
To reduce the environmental impact of our
products, ATEN documentation and software
can be found online at
http://www.aten.com/download/
Technical Support
www.aten.com/support
ATEN NRGence
™
PE0107S/PE0110S/PE0207S/
PE0209S/PE0210S
Basic 1U PDU with surge protection
Quick Start Guide
© Copyright 2019 ATEN® International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All
other trademarks are the property of their respective owners.
This product is RoHS compliant.
Printing Date: 03/2019
PE0107S/PE0110S/PE0207S/PE0209S/PE0210S with surge protection Quick Start Guide
pe0110sa is the example used here. Please confi rm the models corresponding to the given
pictures (models and pictures are not directly related).
Hardware Installation
B
Note: For safety reasons the equipment should be installed near the wall socket outlet and
the disconnected device (appliance coupler on detachable power supply cord or plug
on non-detachable power supply cord) should be readily accessible
Basic PDU
Scan for
more information
EMC Information
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT:
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC Caution: Any changes or modifi cations not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
Warning: Operation of this equipment in a residential environment
could cause radio interference.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는
사용자는 이 점을 주의하시기 바라며, 가정외의 지역에
서 사용하는 것을 목적으로 합니다.
www.aten.com
A
Hardware Review
1
Power Inlet
2
Circuit Breaker
3
Surge Protection
4
Surge Protection Indicator
5
Power Outlets
6
Rack Mount Ears
7
Grounding
B
Hardware Installation
Refer to the installation diagram (the numbers in the diagram correspond to
the numbered steps), and do the following:
1
Connect the Basic PDU's power cord to an AC power source.
2
For each device you want to connect, connect its power cable between
the device's AC socket (where applicable) and any available outlet on the
Basic PDU.
Note: We strongly advise that you do not plug the Basic PDU into a multi
socket extension cord, since it may not receive enough amperage to
operate correctly. Once you have fi nished
C
Rack Mounting
The Basic PDU can be installed in a 1U confi guration on the side of a rack.
To rack mount the device, stabilize the device on the rack and tighten
screws onto the rack mount ears.
Surge Protection Indicator
The Surge Protection Indicator is as shown in the Hardware Review.
It should normally be lit when the unit is powered.
If the indicator is not lit when the unit is powered, please power down the
unit and any connected device safely. Return the unit to the dealer closest to
your location for further assistance.
Loading...