ATEN CS1142DP4C, CS1182DP4C, CS1142DP4, CS1182DP4, CS1184D4C User guide

...
ATEN Secure KVM User Manual
EMC Information
FEDERAL COMMUNICATIONS COMMISSION STATEMENT: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense.
Achtung: Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen verursachen.
Warning: Operation of this equipment in a residential environment could cause radio interference
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
KCC Statement
RoHS
This product is RoHS compliant.
HDMI Trademark Statement
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
ii
ATEN Secure KVM User Manual
China RoHS
iii
ATEN Secure KVM User Manual
User Information
Online Registration
Be sure to register your product at our online support center: https://eservice.aten.com/eServiceCx/Common/productRegister.do
Telephone Support
For telephone support, call this number: International +886-2-8692-6959 China +86-10-5255-0110 Japan +81-3-5615-5811 Korea +82-2-467-6789 North America +1-888-999-ATEN ext 4988 United Kingdom +44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed as is. Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.
iv
ATEN Secure KVM User Manual
Package Contents
The ATEN Secure KVM package consists of: 1 Secure KVM Switch 1 Power Cord 1 User Instructions*
Check to make sure that all of the components are present and in good order. If anything is missing, or was damaged in shipping, contact your dealer.
Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the switch or to any other devices on the Secure KVM installation.
*Please visit our website to download the most up to date version of the manual.
© Copyright 2011–2017 ATEN® International Co., Ltd. Manual Version: v1.03 Manual Date: 2021-1-25 ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved. All other brand names and trademarks are the registered property of their respective owners.
V
ATEN Secure KVM User Manual
Contents
EMC Information .................................................................................................................... ii
China RoHS ............................................................................................................................ iii
User Information .................................................................................................................... iv
Online Registration ................................................................................................................ iv
Telephone Support ................................................................................................................. iv
User Notice .............................................................................................................................. iv
Package Contents .................................................................................................................... V
About This Manual .............................................................................................................. viii
Overview.................................................................................................................................. ix
Conventions .............................................................................................................................. x
Product Information ............................................................................................................... x
Chapter 1 .................................................................................................................................. 1
Introduction ............................................................................................................................. 1
Overview........................................................................................................................... 1
Features ............................................................................................................................. 2
Requirements .................................................................................................................... 4
Console ............................................................................................................................. 4
Computers ......................................................................................................................... 4
Cables ............................................................................................................................... 4
Operating Systems ............................................................................................................ 5
Components ...................................................................................................................... 6
Front View (of ATEN Secure KVM Switch) ................................................................... 6
Rear View (of ATEN Secure KVM Switch) .................................................................... 7
Front View (of ATEN Remote Port Selector) ................................................................. 11
Chapter 2 ................................................................................................................................ 13
Hardware Setup ..................................................................................................................... 13
Before You Begin ........................................................................................................... 13
Stacking .......................................................................................................................... 15
Rack-Mount .................................................................................................................... 15
Installation ...................................................................................................................... 15
Installation Diagram ....................................................................................................... 18
Chapter 3 ................................................................................................................................ 19
Operation ............................................................................................................................... 19
Powering On ................................................................................................................... 19
Manual Switching ........................................................................................................... 20
Port ID Numbering ......................................................................................................... 20
vi
ATEN Secure KVM User Manual
LED Display ................................................................................................................... 20
Chassis Intrusion Detection ............................................................................................ 22
Smart Card and CAC Reader .......................................................................................... 22
Appendix ................................................................................................................................ 23
Safety Instructions .......................................................................................................... 23
General ............................................................................................................................ 23
Consignes de Sécurité ..................................................................................................... 25
Général ............................................................................................................................ 25
Technical Support ........................................................................................................... 27
International .................................................................................................................... 27
North America ................................................................................................................ 27
Specifications .................................................................................................................. 28
Limited Warranty ............................................................................................................ 35
vii
ATEN Secure KVM User Manual
Configuration (with CAC function)
2-Port
4-Port
8-Port
PC Video
Connection
Console Video
Connection
No. of Displays
DisplayPort
DisplayPort
Single
CS1182DP4C
CS1184DP4C
CS1188DP4C
Dual
CS1142DP4C
CS1144DP4C
CS1148DP4C
HDMI
HDMI
Single
CS1182H4C
CS1184H4C
NA
Dual
CS1142H4C
CS1144H4C
NA
DVI
DVI
Single
CS1182D4C
CS1184D4C
CS1188D4C
Dual
CS1142D4C
CS1144D4C
CS1148D4C
Configuration (without CAC function)
2-Port
4-Port
8-Port
PC Video
Connection
Console Video
Connection
No. of Displays
DisplayPort
DisplayPort
Single
CS1182DP4
CS1184DP4
CS1188DP4
Dual
CS1142DP4
CS1144DP4
CS1148DP4
HDMI
HDMI
Single
CS1182H4
CS1184H4
NA
Dual
CS1142H4
CS1144H4
NA
DVI
DVI
Single
CS1182D4
CS1184D4
CS1188D4
Dual
CS1142D4
CS1144D4
CS1148D4
ATTENTION
If the tamper-evident seal is missing or peeled, avoid using the product and contact your ATEN dealer.
If all front panel LEDs on the Secure KVM Switch (except Power) flash continuously, all Remote Port Selector (RPS) LEDs flash, or either enclosure appears breached, avoid using the product and contact your ATEN dealer.
The Secure KVM Switch and the Remote Port Selector (RPS) are equipped with active always-on chassis intrusion detection security. Any attempt to open the enclosure will permanently disable the switch/ RPS, and void the warranty.
Tamper-evident seal
About This Manual
This user manual is intended for system administrators and end users.
This user manual is provided to help you get the most from your ATEN Secure KVM Switch system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below.
This user manual covers the following ATEN Secure KVM Switches:
viii
ATEN Secure KVM User Manual
Overview
Chapter 1, Introduction, introduces you to the ATEN Secure KVM Switch system. Its purpose, features and benefits are presented, and its front and back panel components are described.
Chapter 2, Hardware Setup, provides step-by-step instructions for setting up your installation. Chapter 3, Operation, explains the concepts involved in operating the ATEN Secure KVM Switch. An Appendix, provides specifications and other technical information regarding the ATEN Secure KVM Switch.
ix
ATEN Secure KVM User Manual
Conventions
This manual uses the following conventions:
Product Information
For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and telephone numbers: International https://www.aten.com/global/en/ North America https://www.aten.com/us/en/
x
ATEN Secure KVM User Manual
This Page Intentionally Left Blank
XI
ATEN Secure KVM User Manual
Chapter 1
Introduction
Overview
The ATEN Secure KVM Switch series is NIAP1-certified and compliant with NIAP PPv4.0 (Protection Profile for Peripheral Sharing Device version 4.0)2 requirements, satisfying the latest security requisites set by the U.S. Department of Defense for peripheral sharing devices. Compliance ensures maximum information security while sharing a single set of keyboard, mouse, monitor, speakers, and CAC (Common Access Card) Reader3 between multiple computers. Conformity with Protection Profile v4.0 certifies that other USB peripherals cannot be connected to the console ports of the Secure KVM Switch, and that only a keyboard and mouse are accommodated, therefore providing high-level security, protection and safekeeping of data.
The ATEN Secure KVM Switch hardware security includes tamper-evident tape, chassis intrusion detection, and tamper-proof hardware, while software security features include restricted USB connectivity – non-HIDs (Human Interface Devices) or non-predefined CAC/HIDs are ignored when switching, an isolated channel per port that makes it impossible for data to be transferred between secure and unsecure computers, and automatic clearing of the keyboard and mouse buffer when switching port focus.
By combining physical security with controlled USB connectivity and controlled unidirectional data flow from devices to connected computers only, the ATEN Secure KVM Switch series offers you the means to consolidate multiple workstations of various security classification levels with one keyboard, monitor and mouse (KVM) console.
Note:
1. The National Information Assurance Partnership (NIAP) is a United States government initiative to meet the security testing needs of IT consumers and manufacturers. It is operated by the National Security Agency (NSA) and the National Institute of Standards and Technology (NIST).
2. The ATEN Secure KVM Switch series additionally satisfies Protection Profile version 4.0 for Peripheral Sharing Device (PSD).
3. USB 1.1 for keyboard, mouse connections, and USB 2.0 for CAC reader connection.
1
ATEN Secure KVM User Manual
FEATURES
BENEFITS
2/4/8-Port USB DVI/HDMI/DisplayPort Single/Dual Display Secure KVM Switch*
Reduces the costs involved in controlling up to 8 Single/Dual Display computers while offering data isolation between shared peripherals and computers
Superior ultra high video resolution up to 4K UHD (3840 × 2160 @ 60Hz)**
Supports resolutions up to 3840 x 2160 @ 60Hz with crystal clear image quality
Video DynaSync – exclusive ATEN technology
ATEN Video DynaSyncTM eliminates boot-up display problems and optimizes resolutions when switching between ports
DisplayPort AUX channel filtering (DisplayPort Secure KVM only)
Non-qualified auxiliary channel traffic such as MCCS and EDID write is rejected
NIAP PP PSD v4.0 certified
Provides the most advanced security features required by the latest Protection Profile (PP) v4.0 for Peripheral Sharing Device (PSD)
Pushbutton / Remote Port Selector (RPS)*** port selection and secure port switching
Port selection via pushbutton / Remote Port Selector (RPS) only to enhance security. Keyboard, Mouse, Video, Audio and CAC reader switch together for secure switching.
Channel Isolation
Isolated channel per port makes it impossible for data to be transferred between computers
Shared peripherals and computer isolation
The always-on keyboard, mouse, and display EDID emulation ensures isolation between peripherals and connected computers.
Restricted USB connectivity
Non-authorized HIDs (Human Interface Devices) or non-predefined CAC will be rejected / ignored.
Unidirectional data flow
Secure design enables unidirectional data flow between devices and connected computers.
Administrative configuration and event log functions
Secure access for authorized administrator to audit KVM operation logs and secure configuration. (Please refer to the Administrator guide.)
Supports analogue audio (speaker only)****
Only unidirectional speaker data is allowed preventing the passage of the analogue audio by microphone input or line input.
Active always-on chassis intrusion detection
If physical tampering is detected, the switch or the Remote Port Selector becomes permanently inoperable.
Clears keyboard buffer when switching
Keyboard data buffer is automatically purged when switching KVM port focus.
Tamper-proof hardware
All integrated circuits are soldered directly to the circuit board to prevent tampering with the components.
Tamper-evident tape
Provides a visual indication of any attempt to gain access to the switch (or RPS) internal components.
Features
2
ATEN Secure KVM User Manual
Firmware non-reprogrammable
Prevents tampering and attempts to reprogram the
switch’s firmware.
Metal enclosure
Rugged metal enclosure.
Note:
* HDMI Secure KVM Switch only has 2/4-port models. ** HDMI Secure KVM Switch series supports console video output resolutions up to 4K @ 60 Hz. DisplayPort Secure KVM Switch series supports console video output resolutions up to 4K @ 30 Hz. DVI Secure KVM Switches offer 3840 x 2160 @ 30 Hz video output on compatible HDMI-interfaced monitors/computers with ATEN DVI-to-HDMI KVM cables. *** Remote Port Selector is not supplied in the package and requires a separate purchase **** Only analogue speaker data input is supported. The ATEN Secure KVM Switch does not convert digital audio to analogue audio.
3
ATEN Secure KVM User Manual
Requirements
Console
DVI (for DVI-interfaced Secure KVM), HDMI (for HDMI interfaced Secure KVM), or DisplayPort (for DisplayPort-interfaced Secure KVM) monitor capable of the highest resolution that you will be using on any computer in the installation
USB mouse USB keyboard Speaker (Optional) USB Smart card or CAC (Common Access Card) reader (Optional)* Remote Port Selector (Optional)**
Computers
A DVI/HDMI/DisplayPort video output connector A USB Type A port for keyboard and mouse A USB Type A port for Smart Card or CAC reader (Optional)* A 3.5 mm jack Audio port for speaker (Optional)
Cables
The KVM cable sets which are specifically designed to work with this switch are not supplied in the package and require a separate purchase.
For security, do not connect any cable that has a microphone audio input or line in audio input.
Note:
* Only applicable on the models with CAC function ** Remote Port Selector is not supplied in the package and requires a separate purchase
4
ATEN Secure KVM User Manual
Operating Systems
Suggested operating systems are shown in the table, below:
Note: Supports Linux Kernel 2.6 and higher.
5
ATEN Secure KVM User Manual
Components
Front View (of ATEN Secure KVM Switch)
CS1188D4C
CS1142H4
CS1184DP4C
6
ATEN Secure KVM User Manual
Rear View (of ATEN Secure KVM Switch)
CS1188D4C
CS1142H4
CS1184DP4C
Note:
This user manual uses CS1188D4C, CS1142H4, CS1184DP4C to demonstrate each interface (DVI/HDMI/DisplayPort), port number (2/4/8- Port), CAC support (Yes/No), and number of displays (single/dual) supported by the ATEN Secure KVM Switch.
7
ATEN Secure KVM User Manual
No.
Component
Description
1
Port Selection Pushbuttons
Pressing a Port Selection Pushbutton brings together the keyboard, mouse, video, audio, and CAC reader focus to the computer attached
to its corresponding port.
2
Port and CAC LEDs
The Port / CAC LEDs are located on front panel to indicate Port/CAC reader selection or connection status.
Port LEDs (Lower row; Orange LEDs) Online – Lights dim orange to indicate that the computer attached to its corresponding port is connected and powered on.
Selected – Lights bright orange to indicate that the computer
attached to its corresponding port has the KVM focus. Warning - Flashes to indicate that a non-qualified USB HID device is
connected to console USB keyboard port or mouse port when the corresponding port has the focus. CAC LEDs (Upper row, Green LEDs, CAC models only)
Online – Lights dim green to indicate that the computer attached to its corresponding port has a USB CAC reader cable connection and the CAC function is enabled.
Selected – Lights bright green to indicate that the CAC function is enabled and the computer attached to its corresponding port has the
CAC focus.
None – No lights indicate that the cable is not connected or CAC has been disabled. Warning - Flashes to indicate that a non-qualified USB smart card /
CAC reader is connected when the corresponding port has the focus. Note:
1. CAC function of each port can be enabled or disabled by pressing
the port selection pushbutton for more than 3 seconds (this is a toggle feature). Please refer to the Operation section of this user manual for more information.
2. All front panel LEDs (except the Power LED) will flash
continuously when a chassis intrusion or self-test failure (except for Pushbutton jam) is detected. See Chassis Intrusion Detection
section for further details.
3. Port and CAC LEDs also indicate the status of the Secure KVM
self-test status. See Operation section for further details
3
Reset Button
Press this button to reset the ATEN Secure KVM Switch. Note:
When you perform a reset by pressing the reset button for more than 5 seconds, the keyboard/mouse buffer will be purged and the switch will
reboot and perform a self-test. After a successful self-test, port focus
will be switched to port 1, and the CAC function of each port will be set
8
ATEN Secure KVM User Manual
to factory default setting (enabled). If the Secure KVM fails to generate video on the monitor after a reset,
please power off the installation, check the cables, and follow the instructions found in this manual to power on the installation.
4
Audio Ports
The cables from your speakers plug in here. Note: Only standard analogue speaker connections are allowed. The use of an analogue microphone or line-in audio device is strictly
prohibited.
5
USB Smart Card / CAC
Reader Port (CAC models only)
Only qualified USB authentication devices (e.g., standard smart card and CAC reader) can be plugged into this port.
Note: USB authentication device filter is configurable by authorized administrators for trusted devices (e.g. USB token, USB Biometric reader). Please refer to the Administrator Guide for details.
6
Num Lock LED
Lights green to indicate the Num Lock function has been turned on. Note: The Num Lock LED on the keyboard will be disabled due to
security requirements.
7
Caps Lock LED
Lights green to indicate the Caps Lock function has been turned on. Note: The Caps Lock LED on the keyboard will be disabled due to
security requirements.
8
Scroll Lock LED
Lights green to indicate the Scroll Lock function has been turned on.
Note: The Scroll Lock LED on the keyboard will be disabled due to
security requirements.
9
Power LED
Lights green to indicate that the ATEN Secure KVM Switch is powered
on.
10
USB Console Ports
The USB keyboard and mouse plug into these ports. The USB console
keyboard port (lower port) and mouse port (upper port) support the following – standard USB keyboards/mice, standard USB keyboards/mice via a USB hub, and the HID functions of a composite
device. Note:
1. The console USB keyboard and mouse ports are interchangeable,
meaning you can connect a keyboard to the mouse port and vice versa. However, for optimal operation it is recommended to connect the USB keyboard to the console's USB keyboard port
and the USB mouse to the console's USB mouse port. For security purposes, do not attempt to connect a wireless keyboard or mouse to the switch.
2. Non-standard keyboards/mice with integrated USB hubs and/or
other USB-integrated devices may not be fully supported due to the strict security standards and policy of the ATEN Secure KVM
Switch. If supported, only basic (HID) keyboard/mouse operations
will function.
3. Multimedia keys on the keyboard will not function due to the
9
ATEN Secure KVM User Manual
security policy.
4. The Num Lock, Caps Lock, and Scroll Lock LED on keyboards will
not function due to the security policy.
5. USB HID device filter is configurable by authorized administrators
for trusted devices (only the USB console mouse port is applicable
for setting specific blocked devices). Please refer to the Administrator Guide for details.
11
Remote Port Selector Port
The cable on the Remote Port Selector plugs in here. (Remote Port Selector is not supplied in the package)
12
Video LED(s)
This LED lights green when the video connection is up and running.
The LED flashes when a non-qualified monitor is connected. Note: With the dual-display model, each console video connection has a video LED.
13
Console Monitor Port(s)
The cable from your console monitor plugs in here. Note: The dual-display model has two console monitor ports.
14
KVM Port Section
The custom KVM cables that attach to your computers plug in this section.
15
KVM Audio Port
The audio cable that attaches to your computer plugs in here. Note: Only speaker connections are allowed. The use of an analog
microphone or line-in audio device is strictly prohibited.
16
KVM USB Port
The USB cable that attaches to your computer's keyboard / mouse plugs in here.
17
USB Smart Card / CAC (Common Access Card) Reader Port
The USB cable that attaches to your computer's USB Smart Card /
CAC reader plugs in here.
18
Power Switch
This is a standard rocker switch that powers the ATEN Secure KVM Switch on and off.
19
Power Socket
The AC power cord plugs in here.
10
ATEN Secure KVM User Manual
No.
Component
Description
1
Port Selection Pushbuttons
Pressing a Port Selection Pushbutton brings together the keyboard, mouse, video, audio, and CAC reader focus to the computer attached
to its corresponding port. Note: When attached to a 2-Port Secure KVM Switch, only pushbuttons
numbered 1 and 2 will be detected and functional. When attached to a 4-Port Secure KVM Switch, only pushbuttons numbered 1, 2, 3, and 4 will be detected and functional. When attached to an 8-Port Secure
KVM Switch, all eight pushbuttons will be detected and functional.
2
Port LEDs
The Port LEDs are located on the upper-left side (of each pushbutton) to indicate Port selection and connection status.
Port LEDs (Orange LEDs)
Online – Lights dim orange to indicate that the computer attached to its corresponding port is connected and powered on.
Selected – Lights bright orange to indicate that the computer attached to its corresponding port has the KVM focus. Warning - Flashes to indicate that a non-qualified USB HID device is
connected to console USB keyboard port or mouse port when the corresponding port has the focus.
3
Num Lock LED
Lights green to indicate the Num Lock function has been turned on. Note: The Num Lock LED on the keyboard will be disabled due to security requirements.
4
Caps Lock LED
Lights green to indicate the Caps Lock function has been turned on. Note: The Caps Lock LED on the keyboard will be disabled due to
Front View (of ATEN Remote Port Selector)
11
ATEN Secure KVM User Manual
security requirements.
5
Scroll Lock LED
Lights green to indicate the Scroll Lock function has been turned on. Note: The Scroll Lock LED on the keyboard will be disabled due to security requirements.
6
CAC LED
The CAC LED is located on the far right of the upper bar (on the panel) to indicate CAC reader selection status. CAC LED (Green LED, CAC models only)
Online/Selected – Lights bright green to indicate that the CAC function is enabled and the computer attached to its corresponding port has a USB CAC reader cable connection, and has the CAC focus.
� None – No lights indicate that the cable is not connected or CAC has been disabled. � Warning – Flashes to indicate that a non-qualified USB smart card /
CAC reader is connected when the corresponding port has the focus. Note: All panel LEDs on the RPS will flash continuously when a chassis
intrusion (except for Pushbutton jam) is detected. See Chassis Intrusion Detection section for further details.
7
Port Name Label Area
Port names can be written on labels and placed on these two areas covered with mylar panels for easier port identification.
12
ATEN Secure KVM User Manual
Tamper-evident seal
ATTENTION
If the tamper-evident seal is missing or peeled, avoid using the product and contact your ATEN dealer.
If all front panel LEDs on the Secure KVM Switch (except Power) flash continuously, all Remote Port Selector (RPS) LEDs flash, or either enclosure appears breached, avoid using the product and contact your ATEN dealer.
The Secure KVM Switch and the Remote Port Selector (RPS) are equipped with active always-on chassis intrusion detection security. Any attempt to open the enclosure will permanently disable the switch/ RPS, and void the warranty.
Chapter 2
Hardware Setup
Before You Begin
Tampering prevention and detection
1. The ATEN Secure KVM Switch and the optional Remote Port Selector (RPS) include
tamper-evident tape to provide visual indications of intrusion to the switch/ RPS enclosure. If the tamper-evident seal is missing, peeled, or looks as if it has been adjusted, avoid using the product and contact your ATEN dealer.
2. The ATEN Secure KVM Switch and ATEN RPS are equipped with active always-on chassis
intrusion detection:
- If a mechanical intrusion is detected on the switch, the switch (without RPS connected) will
be permanently disabled and all the front panel LEDs (except the Power LED) will flash continuously.
- If a mechanical intrusion is detected by the RPS (connected with the switch and aligned), this
will permanently disable both the RPS itself and the switch, and all LEDs (on RPS) and the
front panel LEDs except the Power LED (on switch) will flash continuously. If the switch or RPS enclosure appears breeched or all the LEDs are flashing continuously, stop using it, remove it from service immediately and contact your ATEN dealer.
3. Any attempt to open the switch or RPS enclosure will activate the chassis intrusion detection
security, which will render it inoperable and void the warranty.
4. The ATEN Secure KVM Switch cannot be upgraded, serviced or repaired.
5. The ATEN Secure KVM Switch and ATEN RPS contain an internal battery which is
non-replaceable. Never attempt to replace the battery or open the switch or RPS enclosure.
Always use qualified and authorized peripheral devices
1. For security, the ATEN Secure KVM Switch supports only standard USB devices (or pointing
device). Do not connect a wireless keyboard/mouse, or any keyboard/mouse with an internal USB
13
ATEN Secure KVM User Manual
hub or composite device with Non-HID functions to the switch.
2. If a non-qualified keyboard is connected, the keyboard will not function. No keystrokes will be
seen on the screen.
3. If a non-qualified mouse is connected, the mouse will not function. No cursor movement will be
seen on the screen.
4. For security, the USB console keyboard/mouse ports by default only support the following –
standard USB keyboards/mice, standard USB keyboards/mice via a USB hub, and the HID functions of a composite device. Do not connect other USB devices to the USB console keyboard/mouse ports. Non-qualified or non-authorized USB devices will be rejected. For administrative configuration, please refer to the Administrator Guide.
5. Num Lock LED, Caps Lock LED, and Scroll Lock LED on the keyboard will be disabled due to
the security policy.
6. Special multimedia keys on the keyboard will be disabled due to the security policy.
7. For security, the ATEN Secure KVM Switch does not support an analogue microphone or line-in
audio input. Never connect a microphone or headset microphone to the audio output port. Standard analogue speakers and headsets are supported.
8. For security, the USB CAC port by default only supports authorized user authentication devices
such as USB Smartcard or CAC readers. Do not connect other USB devices to the USB CAC port. Non-qualified or non-authorized USB devices will be rejected. For administrative configuration, please refer to the Administrator Guide and Port Authentication Utility Guide for details.
9. For security, do not use any USB CAC authentication device or other peripherals that adopt an
external power source.
10. Always use a qualified monitor. Non-qualified monitors will be rejected.
11. Do not use wireless video transmitters or any docking device.
12. Do not connect any Thunderbolt device to the Secure KVM Switch.
13. Any cable connector or non-ATEN remote controller plugged into the console RPS port will be
ignored.
Secure Installation
1. Do not attempt to connect or install the following devices to the computers connected to the ATEN
Secure KVM Switch: TEMPEST computers; telecommunication equipment; frame grabber video cards; or special audio processing cards.
2. Important safety information regarding the placement of this device is provided on page 24. Please
review it before proceeding.
3. Before installation, make sure the power sources to all devices connected to the installation are
turned off. You must unplug the power cords of any computers that have the Keyboard Power On function.
4. Hot-swapping of the console monitor is not allowed. Power off the Secure KVM Switch and the
14
ATEN Secure KVM User Manual
Note:
1. The console USB keyboard and mouse ports are interchangeable, meaning you can connect a
keyboard to the mouse port and vice versa. However, for optimal operation, it is recommended to connect the USB keyboard to the console’s USB keyboard port and the USB mouse to the console’s USB mouse port.
2. For security purposes, do not attempt to connect a wireless keyboard/mouse to the switch.
3. During KVM operation, non-standard keyboards with integrated USB hubs and/or other
USB-integrated devices may not be fully supported due to the strict security standards and policy of the ATEN Secure KVM Switch. If supported, only basic (HID) keyboard operations will function.
4. When the Secure KVM Switch is powered on, if the keyboard or mouse is rejected, the keyboard
and mouse will be inoperable (mouse cursor freezes and/or no key strokes will respond on the computer).
monitor before changing the console monitor.
5. A computer connected to the Secure KVM Switch should only be powered on after all of the
connections to the device are made (video, USB and audio).
Secure Operation and Administration
Please refer to Administrator Guide for Secure KVM Switch configuration and event log auditing functions.
Stacking
The ATEN Secure KVM Switch features a rugged, metal enclosure which provides stability and allows the unit to be stacked on a desktop. The unit can be placed on any level surface that can safely support its weight and the weight of the attached cables. Ensure that the surface is clean and free of materials that can block the exhaust vents or otherwise interfere with normal operation of the KVM switch.
Rack-Mount
The ATEN Secure KVM Switch features a rack-mount design and offers rack-mount options. Rack-mount kits which are specifically designed to work with this switch are not supplied in the package and require a separate purchase.
Installation
To set up your ATEN Secure KVM Switch installation, refer to the installation diagram on page 18 (the numbers in the diagrams correspond to the steps below), and do the following:
1. Plug your USB keyboard and USB mouse into the USB console ports located on the unit’s rear
panel. (The console USB keyboard/mouse ports are only compatible with standard USB keyboards/mice).
15
ATEN Secure KVM User Manual
Note:
1. When the ATEN Secure KVM Switch is powered on, the Video LED lights green when the
video connection is up and running. The Video LED flashes when a non-qualified monitor is connected.
2. Due to the security policy, the ATEN Secure KVM Switch does not support a monitor hot-swap.
If you would like to change the console monitor, you must first power off the entire installation.
3. Connected monitors will be filtered when the ATEN Secure KVM Switch is powered on.
Non-qualified monitors will be rejected (Video LED flashes). Please refer to the LED Display for detailed visual identification.
Note:
Only speaker connections are allowed. The use of an analogue microphone or line-in audio connection is strictly prohibited.
Note:
1. Verify that all the plugs are in the same KVM port sockets (all in Port 1, all in Port 2, etc.). Each
socket is marked with an appropriate icon.
2. If the CAC reader function is to be disabled for certain PCs, its advised not to connect a USB
CAC cable in the installation.
2. Plug your console monitor(s) into the console video port(s) located on the unit’s rear panel and
power on the monitor.
3. Plug your speakers into the console's speaker jack located on the unit’s front panel.
4. With a single-display Secure KVM Switch, using a KVM cable set (not supplied with this package
and must be purchased separately), plug the video connector into any available video socket in the KVM port section of the switch, then plug the accompanying USB (keyboard/mouse or CAC) and speaker connectors into their corresponding USB and speaker ports. With a dual-display Secure KVM Switch, using a KVM cable set (not supplied with this package and must be purchased separately), plug the video connector for your primary monitor into any available video socket A in the KVM port section of the switch. Using another video cable and plug the video connector for your secondary monitor into video socket B on the same KVM port section of the switch, then plug the accompanying USB (Keyboard/Mouse or CAC) and speaker connectors into their corresponding USB and speaker sockets.
.
5. At the other end of the KVM cable set, plug the USB, video, and speaker cables into their
respective ports on the computer. With a dual-display Secure KVM Switch, at the other end of the other video cable, plug this video cable into its respective port on the computer.
16
ATEN Secure KVM User Manual
Note:
1. Only appropriate qualified USB authentication devices (e.g., Smart Card and CAC readers by
default) can be plugged into this port. During KVM operation, non-qualified or non-authorized USB devices will be filtered and rejected (the CAC LED that has port focus will flash). Please refer to the LED display for visual indications.
2. The CDF (Configurable Device Filtration) function can only be operated by authorized
administrators. Please refer to the Administrator Guide and Port Authentication Utility Guide for details.
3. An active session on the selected computer is immediately terminated upon removal of the CAC
card.
Note:
1. Verify that the second video plug is in the same KVM port section as the first video plug (all in
Port 1, all in Port 2, etc.). Each socket is marked with an appropriate icon.
2. Repeat steps 4, 5 for each computer you are installing.
3. With a dual-display installation, for easier cabling at your site, you can also connect all the
primary video connectors to video sockets B, and secondary video connectors to video sockets A. Make sure the consoles primary and secondary monitors are connected the same way.
Note:
The ATEN Secure KVM Switch performs a security self-test at power-on and at each power cycle. Front panel LEDs will indicate the self-test status and test result. Please refer to the Operation section and LED Display section for visual identification details.
Note:
1. Be sure to connect the RPS before the ATEN Secure KVM Switch is powered-on.
2. Any connection of RPS after the ATEN Secure KVM Switch is powered-on will not be detected
by the switch.
6. Plug the USB Smart Card / CAC reader to the console CAC port on the front panel. (Optional)
7. Plug the cable on the RPS into the console RPS port. (Optional)
8. Plug the female end of the power cord into the ATEN Secure KVM Switch power socket; plug the
male end into an AC power source.
9. Turn on the ATEN Secure KVM Switch and check that the LEDs light up. The ATEN Secure
KVM Switch will start a self-test.
17
ATEN Secure KVM User Manual
Installation Diagram
Rear View
13
Front View
18
ATEN Secure KVM User Manual
Chapter 3
Operation
Powering On
When you power on, reset, or power cycle the ATEN Secure KVM Switch, the switch will perform a self-test to check the unit’s integrity and security functions.
During the self-test
All Port LEDs, all CAC LEDs (if supported), Num Lock LED, Caps Lock LED, and Scroll Lock LED on the Secure KVM will turn ON and then OFF. The KVM focus will be switched to Port 1 when the self-test completes successfully (Port 1 LED lights bright orange).
Self-test failure
In the case of a self-test failure, the Secure KVM Switch becomes inoperable, with front panel LED combinations (on the Secure KVM) indicating the potential cause of the failure (such as button jam or KVM integrity compromise)
A pre-defined combination of the Port and CAC LEDs indicate the cause of the failure. If all front panel LEDs on the Secure KVM (except the Power LED) flash continuously, it means
KVM tampering is detected or a self-test failure has occurred (except for Pushbutton jam; see below) If Pushbutton jam is detected, both the ports LEDs (Port LED and CAC LED) will flash.
For security, the ATEN Secure KVM Switch becomes inoperable if the self-test fails. Please verify your KVM installation by checking that the front panel pushbuttons are not stuck and then power cycle the Secure KVM Switch. If the self-test failure remains, stop using the ATEN Secure KVM Switch immediately, remove it from service and contact your ATEN dealer.
After the ATEN Secure KVM Switch is powered on and ready, power on your computers. By default the ATEN Secure KVM Switch will switch to Port 1 after a successful self-test.
The ATEN Secure KVM Switch filters and emulates both a mouse and keyboard on each port after the unit is powered on. If the keyboard, mouse, monitor, or Smart card / CAC reader fails to operate properly, make sure that you are using the appropriate peripherals (qualified and authorized peripherals); then power off the ATEN Secure KVM Switch, check all the cable connections, and power on the unit again.
19
ATEN Secure KVM User Manual
Manual Switching
For increased security, the ATEN Secure KVM Switch offers manual port switching only. This is achieved by pressing the port selection pushbuttons located on the switch front panel or pressing the port selection pushbuttons located on the RPS panel (if RPS is connected and aligned) Press and release a port selection pushbutton to bring the KVM focus to the computer attached to its corresponding port (see Port ID Numbering, below). To meet maximum security and channel isolation requirements, the keyboard, mouse, video, audio, and USB CAC reader ports will be switched together. The Selected Port LED lights bright orange (on Switch and/or RPS) to indicate that the computer attached to its corresponding port has the KVM focus (keyboard, mouse, monitor, audio, and CAC reader).
The PC that has the port focus should be able to detect the peripherals after port switching. If the PC fails to detect the keyboard, mouse, or CAC reader:
- Verify that the keyboard, mouse, and/or CAC reader is qualified.
- Verify that the keyboard, mouse, or CAC reader hasnt failed.
- For USB CAC reader (USB authentication device), please make sure that the USB CAC cable has
been securely connected, and the CAC function is enabled.
- For USB CAC reader port, please contact your administrator to verify if the device has been
authorized.
Port ID Numbering
Each KVM port on the ATEN Secure KVM Switch is assigned a port number (1–2 for the 2-Port models; 1–4 for the 4-Port models; 1–8 for the 8-Port models). The port numbers are marked on the rear of the switch. See Rear View, page 7. The port ID of a computer is derived from the KVM port number it is connected to.
LED Display
In addition to the Power LED, the ATEN Secure KVM Switch (and ATEN RPS) has Port LEDs (Online and Selected), keyboard lock (Num Lock/Caps Lock/Scroll Lock) LEDs and CAC LEDs that are built into the front panel to indicate port / keyboard / CAC reader operating status. A video LED is located on the back panel (of the switch) to indicate the operating status of the video connection. These LEDs also serve as the alarm notification for KVM security issues.
20
ATEN Secure KVM User Manual
LED
Indication
Power LED (on the Secure KVM switch)
The Power LED is on the front panel and lights green to indicate that the KVM switch is powered on.
Video LED (on the Secure KVM switch)
The Video LED is located on the back panel next to each video connector. The LED lights green when the video connection is up and running. The LED flashes when a non-qualified monitor is connected.
Port LED (on the Secure KVM switch and the RPS)
The Port LEDs are located on the front panel (of the switch) and the upper-left side of each pushbutton (of the RPS) to indicate the port selection or connection status.
� Online – Lights dim orange to indicate that the computer attached to its corresponding port connected and powered on. � Selected – Lights bright orange to indicate that the computer attached to its corresponding port has the KVM focus. � Warning - Flashes to indicate that a non-qualified USB HID device is connected to console USB keyboard port or mouse port when the corresponding port has the focus.
Note:
1. Port and CAC LEDs will flash constantly when a chassis
intrusion is detected. See Chassis Intrusion Detection section for details.
2. Port and CAC LEDs (on the Secure KVM switch) also indicate
the status of the Secure KVM self-test status. See Operation section for further details.
CAC LED (on the Secure KVM switch and the RPS) CAC models only
The CAC LEDs are located on the front panel (of the switch) and the far right of the upper bar on the panel (of the RPS) to indicate CAC reader selection or connection status. � Online – Lights dim green to indicate that the computer attached to its corresponding port has a USB CAC reader cable connection and the CAC function is enabled. � Selected – Lights bright green to indicate that the CAC function is enabled and the computer attached to its corresponding port has the CAC focus. � None – No lights indicate that the cable is not connected or CAC has been disabled. � Warning - Flashes to indicate that a non-qualified USB Smart card / CAC reader is connected when the corresponding port has the focus.
Note:
- The CAC function of each port can be enabled or disabled by
21
ATEN Secure KVM User Manual
pressing the port selection button (on the switch) for more than 3 seconds (this is a toggle feature). Please refer to Operation section for details.
- Port and CAC LEDs will flash constantly when a chassis intrusion is detected. See Chassis Intrusion Detection section for further details.
Num Lock LED (on the Secure KVM switch and the RPS)
Lights green to indicate the Num Lock is enabled
Caps Lock LED (on the Secure KVM switch and the RPS)
Lights green to indicate the Caps Lock is enabled
Scroll Lock LED (on the Secure KVM switch and the RPS)
Lights green to indicate the Scroll Lock is enabled
Chassis Intrusion Detection
To help prevent malicious tampering with the ATEN Secure KVM Switch, the switch (or the RPS) becomes inoperable and all front panel LEDs on the Secure KVM switch (except Power) or all Remote Port Selector (RPS) LEDs flash constantly when a chassis intrusion (such as the cover being removed) is detected (by the switch or by the RPS). The intrusion detection protection is an always-on function. If all front panel LEDs on the Secure KVM Switch (except Power) flash continuously, all Remote Port Selector (RPS) LEDs flash, or either enclosure appears breached, avoid using the product and contact your ATEN dealer.
Smart Card and CAC Reader (CAC models only)
The USB Smart Card / CAC reader function of each port can be enabled or disabled (enabled by default). Press the port selection pushbutton (on the switch) for more than 3 seconds then release it, to enable/disable the CAC reader function for that port (this is a toggle feature). The CAC LEDs are used to indicate the CAC reader operation status. If the CAC reader function is to be disabled for certain PCs, its advised not to connect a USB CAC cable to the installation.
22
ATEN Secure KVM User Manual
Appendix
Safety Instructions
General
This product is for indoor use only. Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious
damage will result.
Do not use the device near water. Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation*.To ensure
reliable operation, and to protect against overheating, the cabinet must never be blocked or covered. The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings*. Placing devices without slots or openings on a soft surface will affect the heat dissipation. The device should not be placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device. Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a
damp cloth for cleaning. The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V phase-to-phase voltage. To prevent damage to your installation it is important that all devices are properly grounded. The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable
to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/national wiring codes. Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over. If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing rests on any cables. Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage
23
ATEN Secure KVM User Manual
points or short out parts resulting in a risk of fire or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to qualified service personnel. If the following conditions occur, unplug the device from the wall outlet and bring it to qualified
service personnel for repair.
The power cord or plug has become damaged or frayed. Liquid has been spilled into the device. The device has been exposed to rain or water. The device has been dropped, or the cabinet has been damaged. The device exhibits a distinct change in performance, indicating a need for service. The device does not operate normally when the operating instructions are followed. Suitable for installation in Information Technology Rooms in accordance with Article 645 of the
National Electrical Code and NFPA 75.
CAUTION: Never attempt to replace battery or open the switch’s enclosure.
*Note: Not all devices have slots or openings to allow for ventilation
24
ATEN Secure KVM User Manual
Consignes de Sécurité
Général
Ce produit est destiné exclusivement à une utilisation à l’intérieur. Veuillez lire la totalité de ces instructions. Conservez-les afin de pouvoir vous y référer
ultérieurement.
� Respectez l’ensemble des avertissements et instructions inscrits sur l’appareil. � Ne placez jamais l’unité sur une surface instable (chariot, pied, table, etc.). Si l’unité venait à tomber,
elle serait gravement endommagée.
� N’utilisez pas l’unité à proximité de l’eau. � Ne placez pas l’unité à proximité de ou sur des radiateurs ou bouches de chaleur. � Le boîtier de l’unité est destiné à assurer une ventilation adequate*. Pour garantir un fonctionnement
fiable et protéger l’unité contre les surchauffes, le boîtier de l’unité ne doit jamais être obstrué ou couvert. L’unité ne doit jamais être placée sur une surface molle (lit, canapé, tapis, etc.) car ceci obstruerait les ouvertures de ventilation*. Le fait de placer des appareils sans fente ni ouverture sur une surface souple affecte la dissipation thermique. L’appareil ne doit pas être placé dans une enceinte intégrée à moins de lui fournir une ventilation adéquate.
� Ne renversez jamais de liquides de quelque sorte que ce soit sur l’unité. � Débranchez l’appareil de la prise secteur avant nettoyage. Ne pas utiliser de nettoyant liquide ou en
aérosol. Utiliser une chiffon humidifié pour le nettoyage.
� L’appareil doit être alimenté par le type de source indiqué sur l’étiquette. Si vous n’êtes pas sûr du type d’alimentation disponible, consultez votre revendeur ou le fournisseur local d’électricité. � L’appareil est conçu pour les systèmes de distribution d’alimentation informatique avec une tension
phase à phase de 230V Afin de ne pas endommager votre installation, vérifiez que tous les périphériques sont correctement mis à la terre. L’unité est équipée d’une fiche de terre à trois fils. Il s’agit d’une function de sécurité. Si vous ne parvenez pas à insérer la fiche dans la prise murale, contactez votre électricien afin qu’il remplace cette dernière qui doit être obsolète. Respectez toujours les codes de câblage en vigueur dans votre région/pays.
Veuillez à ce que rien ne repose sur le cordon d’alimentation ou les câbles. Acheminez le cordon d’alimentation et les câbles de sorte que personne ne puisse marcher ou trébucher dessus. En cas d’utilisation d’une rallonge avec cette unité, assurez-vous que le total des ampérages de tous
les produits utilisés sur cette rallonge ne dépasse pas l’ampérage nominal de cette dernière. Assurez-vous que le total des ampérages de tous les produits branchés sur la prise murale ne dépasse
25
ATEN Secure KVM User Manual
pas 15 Ampères. Pour contribuer à protéger votre système contre les augmentations et diminutions soudaines et transitoires de puissance électrique, utilisez un parasurtenseur, un filtre de ligne ou un système
d’alimentation sans coupure (UPS). � Placez les câbles du système et les câbles d’alimentation avec précaution ; veillez à ce que rien ne
repose sur aucun des câbles. N’insérez jamais d’objets de quelque sorte que ce soit dans ou à travers les fentes du boîtier. Ils pourraient entrer en contact avec des points de tension dangereuse ou court-circuiter des pièces, entraînant ainsi un risqué d’incendie ou de choc électrique. N’essayez pas de réparer l’unité vous-même. Confiez toute opération de réparation à du personnel qualifié. Si les conditions suivantes se produisent, débranchez l’unité de la prise murale et amenez-la à un technicien qualifié pour la faire réparer:
� Le cordon d’alimentation ou la fiche ont été endommagés ou éraillés. � Du liquide a été renversé dans l’unité. � L’unité a été exposée à la pluie ou à l’eau. � L’unité est tombée ou le boîtier a été endommagé. � Les performances de l’unité sont visiblement altérées, ce qui indique la nécessité d’une réparation. � L’unité ne fonctionne pas normalement bien que les instructions d’utilisation soient respectées. � Peut être installé dans des salles de matériel de traitement de l’information conformément à l’article
645 du National Electrical Code et à la NFPA 75.
ATTENTION : Ne jamais tenter de remplacer la batterie interne ni d'ouvrir le boîtier du commutateur.
*Remarque : Tous les appareils ne disposent pas de fentes ou d’ouvertures qui permettent la ventilation.
26
ATEN Secure KVM User Manual
Email Support
support@aten-usa.com
Online Technical Support
Troubleshooting Documentation Software Updates
https://eservice.aten.com/eServiceCx/supportIndex.do?lang =en_US
Telephone Support
1-888-999-ATEN ext 4988
Technical Support
International
For online technical support – including troubleshooting and documentation:
http://eservice.aten.com
For telephone support, See Telephone Support, page iv:
North America
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase. Your computer configuration, including operating system, revision level,
expansion cards, and software.
Any error messages displayed at the time the error occurred. The sequence of operations that led up to the error. Any other information you feel may be of help.
27
ATEN Secure KVM User Manual
Function
CS1182DP4C
CS1184DP4C
CS1188DP4C
CS1182DP4
CS1184DP4
CS1188DP4
Computer
Connections
Direct 2 4 8 2 4 8
Max. 2 4 8 2 4 8
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
1 x DisplayPort Female (Black)
1 x DisplayPort Female (Black)
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
Video
2 x DP
Female
4 x DP
Female
8 x DP
Female
2 x DP
Female
4 x DP
Female
8 x DP
Female
CAC
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
NA
Speaker
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
Microphone
N/A
NA
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
8 (Orange)
2 (Orange)
4 (Orange)
8 (Orange)
CAC activated
2 (Green)
4 (Green)
8 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
1 (Green, on back panel)
1 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
Max. 3840 x 2160 @ 30 Hz (UHD)
Max. 3840 x 2160 @ 30 Hz (UHD)
Specifications
ATEN Single Display DisplayPort Secure KVM (CAC and Non-CAC models)
28
ATEN Secure KVM User Manual
I/P Rating
100–240V~ ; 50-60 Hz; 1A (TBD)
100–240V~ ; 50-60 Hz; 1A (TBD)
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
Weight
1.76kg (TBD)
1.81kg (TBD)
3.30kg (TBD)
1.76kg (TBD)
1.81kg (TBD)
3.30kg (TBD)
Dimensions
(L x W x H)
335 x 164 x
44 mm
335 x 164 x
44 mm
432 x 205 x
66 mm
335 x 164 x
44 mm
335 x 164 x
44 mm
432 x 205 x
66 mm
Function
CS1142DP4C
CS1144DP4C
CS1148DP4C
CS1142DP4
CS1144DP4
CS1148DP4
Computer
Connections
Direct 2 4 8 2 4 8
Max. 2 4 8 2 4 8
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
2 x DisplayPort Female (Black)
2 x DisplayPort Female (Black)
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
Video
4 x DP
Female
8 x DP
Female
16 x DP
Female
4 x DP
Female
8 x DP
Female
16 x DP
Female
CAC
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
NA
Speaker
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
Microphone
N/A
NA
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
8 (Orange)
2 (Orange)
4 (Orange)
8 (Orange)
ATEN Dual Display DisplayPort Secure KVM (CAC and Non-CAC models)
29
ATEN Secure KVM User Manual
CAC activated
2 (Green)
4 (Green)
8 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
2 (Green, on back panel)
2 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
Max. 3840 x 2160 @ 30 Hz (UHD)
Max. 3840 x 2160 @ 30 Hz (UHD)
I/P Rating
100–240V~ ;
50-60 Hz; 1A
100–240V~ ; 50-60 Hz; 1.5A
100–240V~ ;
50-60 Hz; 1A
(TBD)
100–240V~ ; 50-60 Hz; 1.5A
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
Weight
2.13kg (TBD)
2.18kg (TBD)
3.22kg (TBD)
2.13kg (TBD)
2.18kg (TBD)
3.22kg (TBD)
Dimensions
(L x W x H)
335 x 164 x
66 mm
335 x 164 x
66 mm
432 x 205 x
66 mm
335 x 164 x
66 mm
335 x 164 x
66 mm
432 x 205 x
66 mm
Function
CS1182H4C
CS1184H4C
CS1182H4
CS1184H4
Computer
Connections
Direct 2 4 2 4
Max. 2 4 2 4
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
1 x HDMI Female (Black)
1 x HDMI Female (Black)
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B Female
4 x USB-B Female
2 x USB-B Female
4 x USB-B Female Video
2 x HDMI Female
4 x HDMI Female
2 x HDMI Female
4 x HDMI Female
CAC
2 x USB-B Female
4 x USB-B Female
NA
Speaker
2 x Mini Stereo Jack
Female
4 x Mini Stereo Jack
Female
2 x Mini Stereo Jack
Female
4 x Mini Stereo Jack
Female
Microphone
N/A
NA
ATEN Single Display HDMI Secure KVM (CAC and Non-CAC models)
30
ATEN Secure KVM User Manual
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
2 (Orange)
4 (Orange)
CAC activated
2 (Green)
4 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
1 (Green, on back panel)
1 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
Max. 3840 x 2160 @ 60 Hz (UHD)
Max. 3840 x 2160 @ 60 Hz (UHD)
I/P Rating
100–240V~ ; 50-60 Hz; 1A (TBD)
100–240V~ ; 50-60 Hz; 1A (TBD)
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
Weight
1.76kg (TBD)
1.76kg (TBD)
1.76kg (TBD)
1.76kg (TBD)
Dimensions
(L x W x H)
335 x 164 x 44 mm
335 x 164 x 44 mm
335 x 164 x 44 mm
335 x 164 x 44 mm
Function
CS1142H4C
CS1144H4C
CS1142H4
CS1144H4
Computer
Connections
Direct 2 4 2 4
Max. 2 4 2 4
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
2 x HDMI Female (Black)
2 x HDMI Female (Black)
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B Female
4 x USB-B Female
2 x USB-B Female
4 x USB-B Female Video
4 x HDMI Female
8 x HDMI Female
4 x HDMI Female
8 x HDMI Female
ATEN Dual Display HDMI Secure KVM (CAC and Non-CAC models)
31
ATEN Secure KVM User Manual
CAC
2 x USB-B Female
4 x USB-B Female
NA
Speaker
2 x Mini Stereo Jack
Female
4 x Mini Stereo Jack
Female
2 x Mini Stereo Jack
Female
4 x Mini Stereo Jack
Female
Microphone
N/A
NA
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
2 (Orange)
4 (Orange)
CAC activated
2 (Green)
4 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
2 (Green, on back panel)
2 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
Max. 3840 x 2160 @ 60 Hz (UHD)
Max. 3840 x 2160 @ 60 Hz (UHD)
I/P Rating
100–240V~ ; 50-60 Hz; 1A (TBD)
100–240V~ ; 50-60 Hz; 1A (TBD)
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
Weight
2.06kg (TBD)
2.11kg (TBD)
2.06kg (TBD)
2.11kg (TBD)
Dimensions
(L x W x H)
335 x 164 x 66 mm
335 x 164 x 66 mm
335 x 164 x 66 mm
335 x 164 x 66 mm
Function
CS1182D4C
CS1184D4C
CS1188D4C
CS1182D4
CS1184D4
CS1188D4
Computer
Connections
Direct 2 4 8 2 4 8
Max. 2 4 8 2 4 8
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
1 x DVI-I DL Female
1 x DVI-I DL Female
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
ATEN Single Display DVI Secure KVM (CAC and Non-CAC models)
32
ATEN Secure KVM User Manual
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
Video
2 x DVI-I DL
Female
4 x DVI-I DL
Female
8 x DVI-I DL
Female
2 x DVI-I DL
Female
4 x DVI-I DL
Female
8 x DVI-I DL
Female
CAC
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
NA
Speaker
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
Microphone
N/A
NA
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
8 (Orange)
2 (Orange)
4 (Orange)
8 (Orange)
CAC activated
2 (Green)
4 (Green)
8 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
1 (Green, on back panel)
1 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
DVI Dual Link: 2560 x 1600*
DVI Dual Link: 2560 x 1600*
I/P Rating
100–240V~ ; 50-60 Hz; 1A (TBD)
100–240V~ ; 50-60 Hz; 1A (TBD)
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
Weight
1.79kg (TBD)
1.80kg (TBD)
3.35kg (TBD)
1.79kg (TBD)
1.80kg (TBD)
3.35kg (TBD)
Dimensions
(L x W x H)
335 x 164 x
44 mm
335 x 164 x
44 mm
432 x 205 x
66 mm
335 x 164 x
44 mm
335 x 164 x
44 mm
432 x 205 x
66 mm
Function
CS1142D4C
CS1144D4C
CS1148D4C
CS1142D4
CS1144D4
CS1148D4
Computer
Direct 2 4 8 2 4 8
* DVI Secure KVM Switches offer 3840 x 2160 @ 30 Hz video output on compatible HDMI-interfaced monitors/computers with ATEN DVI-to-HDMI KVM cables
ATEN Dual Display DVI Secure KVM (CAC and Non-CAC models)
33
ATEN Secure KVM User Manual
Connections
Max. 2 4 8 2 4 8
Console Connections
1 Direct
1 Direct
Port Selection
Pushbutton, Remote Port Selector
Pushbutton, Remote Port Selector
Connectors
Console
Ports
Keyboard
1 x USB Type A Female
1 x USB Type A Female
Video
2 x DVI-I DL Female
2 x DVI-I DL Female
Mouse
1 x USB Type A Female
1 x USB Type A Female
Speaker
1 x Mini Stereo Jack Female (Green)
1 x Mini Stereo Jack Female (Green)
Microphone
N/A
NA
CAC
1 x USB Type A Female
NA
KVM Ports
Keyboard/
Mouse
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
Video
4 x DVI-I DL
Female
8 x DVI-I DL
Female
16 x DVI-I DL
Female
4 x DVI-I DL
Female
8 x DVI-I DL
Female
16 x DVI-I DL
Female
CAC
2 x USB-B
Female
4 x USB-B
Female
8 x USB-B
Female
NA
Speaker
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
2 x Mini Stereo
Jack Female
4 x Mini Stereo
Jack Female
8 x Mini Stereo
Jack Female
Microphone
N/A
NA
Power
1 x 3-prong AC Socket
1 x 3-prong AC Socket
Remote Port Selector
1 x RJ-11
1 x RJ-11
Switches
Port
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
2 x Pushbuttons
4 x Pushbuttons
8 x Pushbuttons
Reset
1 x Semi-recessed Pushbutton
1 x Semi-recessed Pushbutton
Power
1 x Rocker
1 x Rocker
LEDs
On Line / Selected
2 (Orange)
4 (Orange)
8 (Orange)
2 (Orange)
4 (Orange)
8 (Orange)
CAC activated
2 (Green)
4 (Green)
8 (Green)
NA
Power
1 (Green)
1 (Green)
Key Lock LED
3 (Green; Num Lock, Caps Lock, Scroll Lock)
3 (Green; Num Lock, Caps Lock, Scroll Lock)
Console Video
2 (Green, on back panel)
2 (Green, on back panel)
Emulation
Keyboard/Mouse
USB
USB
Video
DVI Dual Link: 2560 x 1600*
DVI Dual Link: 2560 x 1600*
I/P Rating
100–240V~ ;
50-60 Hz; 1A
100–240V~ ;
50-60 Hz; 1.5A
100–240V~ ;
50-60 Hz; 1A
100–240V~ ;
50-60 Hz; 1A
100–240V~ ;
50-60 Hz; 1.5A
100–240V~ ;
50-60 Hz; 1A
Environment
Operating Temp.
0–50°C
0–50°C
Storage Temp.
-20–60°C
-20–60°C
Humidity
0–80% RH, Non-condensing
0–80% RH, Non-condensing
Physical Properties
Housing
Metal
Metal
34
ATEN Secure KVM User Manual
Weight
2.14kg (TBD)
2.18kg (TBD)
3.34kg (TBD)
2.14kg (TBD)
2.18kg (TBD)
3.34kg (TBD)
Dimensions
(L x W x H)
335 x 164 x
66 mm
335 x 164 x
66 mm
432 x 205 x
66 mm
335 x 164 x
66 mm
335 x 164 x
66 mm
432 x 205 x
66 mm
* DVI Secure KVM Switches offer 3840 x 2160 @ 30 Hz video output on compatible HDMI-interfaced monitors/computers with ATEN DVI-to-HDMI KVM cables
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or statutory with respect to the contents or use of this documentation, and especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the device or documentation without obligation to notify any individual or entity of such revisions, or update. For further inquiries, please contact your direct vendor.
35
Loading...