CONSOLE
AC 9V
REMOTE I /O
CONSOLE
AC 9V
REMOTE I /O
User Manual
CE-250
Read this guide thoroughly and follow the installation and
operation procedures carefully in order to prevent any damage to
the units and/or any devices that connect to them.
This package contains:
1 CE-250L KVM Extender (Local Unit)
1 CE-250R KVM Extender (Remote Unit)
1 CS Custom KVM Cable
2 Power Adapters
1 User Manual
If anything is damaged or missing, contact your dealer.
Copyright © 2006 ATEN® International Co., Ltd.
Manual Part No. PAPE-1221-100
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights
reserved. All other trademarks are the property of their respective owners.
Printing Date: 11/2006
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the
instruction manual, may cause interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna;
Increase the separation between the equipment and
receiver;
Connect the equipment into an outlet on a circuit
different from that which the receiver is connected;
Consult the dealer or an experienced radio/television
technician for help.
Overview
Because the CE-250 KVM Extender System allows access to a
computer system from a remote console (keyboard, monitor, and
mouse), it is perfect for factory and construction sites, or any type
of installation where the console needs to be in a conveniently
accessible location, but you want the system equipment to reside
in a safe place - away from dust, dirt, and harsh environmental
influences.
The CE-250 System is also useful for control and security
purposes, where you can have the system unit in a secure area
at the same time that you put the console in a location that offers
convenient access.
The CE-250 KVM Extender provides the ideal means to access
the remote system box, since it improves on previous designs by
using inexpensive Category 5 cable - the kind commonly used in
Ethernet networks - instead of bulkier, more expensive, standard
cables. Category 5 cabling makes for a much neater, more
convenient, more reliable data transfer connection.
The CE-250 features a custom ASIC to ensure the utmost in
reliability and compatibility, and can also sense the distance to
the system and automatically adjust the gain to compensate.
Setup is as easy as can be - simply connect the computer system
box and local console to the Local CE-250 Module; run the Cat.
5 cable to the Remote CE-250 Module (up to 150 meters away);
and plug the remote console into the Remote Module.
Note: You can control numerous remote systems from a single
console by combining the CE-250 with a KVM switch.
- 3 -
Features
Built-in ASIC for greater reliability and compatibility
Cat 5 cable to connect the local and remote units – up to 150
meters apart
Dual console operation – control your system from both the
local and remote PS/2 keyboard, monitor, and mouse
consoles
Push button selection – of the active console
High resolution video – up to 1280 x 1024
Supports VGA, SVGA, and multisync monitors
Local monitor supports DDC; DDC2; DDC2B
Automatic gain control – automatically adjust s signal strength
to compensate for distance
Easy to install – no software required – connecting cables to
the devices is all it takes
System Requirements
Consoles
A VGA, SVGA, or Multisync monitor capable of the highest
resolution that you will be using on any computer in the
installation
A PS/2 style keyboard
A PS/2 style mouse
Note: 1. If you connect a DDC type monitor to the Local Unit, the
monitor that connects to the Remote Unit must be able
to support the highest video resolution that the DDC
monitor can provide.
2. You must use the same brand and model of mouse on
both the local and remote units.
- 4 -
Computers
The following equipment must be installed on each computer that
is to be connected to the system:
With PS/2 Type Connectors:
A VGA, SVGA, or Multisync card
A 6-pin mini-DIN mouse port
A 6-pin mini-DIN Keyboard port
With A T Type Connectors:
A VGA, SVGA or Multisync card
A DB-9 (standard serial), mouse port plus mouse adapter
(part # 2A-105)*
A 5-pin DIN (standard AT), keyboard port plus keyboard
adapter (part # 2A-106)*
* Not included - requires separate purchase.
Cables
Although it is possible to use standard KVM cables to link
computers with PS/2 type keyboard and mouse ports to the
CE-250L, for optimal signal integrity, and to simplify the
layout, we strongly recommend that you use the high quality
CS Custom KVM Cable that is provided with this package.
It is not possible to use standard KVM cables to link
computers with AT type keyboard and mouse ports to the CE250L. For those computers, CS Custom KVM Cables must be
used.
Category 5 cable is the minimum required to connect the local
and remote CE-250 units. Cable of a lesser standard will
result in degrading the video signal. For best performance, we
strongly recommend Category 5 cable.
- 5 -
Components
The Local Unit (CE-250L)
Front View:
1
2
CONSOLE
3
4
5
# Description Function
1 Operating Mode
Selection
Switch
Pressing this button toggles between the operating
mode choices:
Local: only the local console can control the
system(s)
AC 9V
/O
REMOTE I
7
6
Auto: both consoles can control the system(s).
2 LEDs The Local Unit has two LEDs to indicate the operating
3 Mouse Port The local PS/2 mouse plugs into this connector.
4 Keyboard Port The local PS/2 keyboard plugs into this connector.
5 Monitor Port The local monitor plugs into this connector.
6 Remote I/O The Cat 5 twisted pair cable that connects to the
7 Power Jack The cable from the AC Power Adapter plugs into this
status of the Local and Remote units (see CE-250L
(Local Unit), p. 11).
Remote Unit plugs into this connector.
jack.
- 6 -
The Local Unit (CE-250L)
Rear View:
CPU
1
2
3
# Description Function
1 Monitor Port The HDB-15 Video connector of the KVM cable that
2 Keyboard Port The Keyboard connector of the KVM cable that
3 Mouse Port The Mouse connector of the KVM cable that connects to
Note: If you are combining the CE-250 with a KVM switch, the
KVM cable connects back to the respective ports on the
Console section of the switch.
connects to the computer's Video port plugs into this
connector.
connects to the computer's Keyboard port plugs into this
connector.
the computer's Mouse port plugs into this connector.
- 7 -
The Remote Unit (CE-250R)
Front View:
1
CONSOLE
2
3
4
# Description Function
1 LEDs The Remote Unit has two LEDs (Power and On Line) to
2 Mouse Port The remote PS/2 mouse plugs into this connector.
3 Keyboard Port The remote PS/2 keyboard plugs into this connector.
4 Monitor Port The remote monitor plugs into this connector.
5 Remote I/O The Cat 5 twisted pair cable that connects back to the
6 Power Jack The cable from the AC Power Adapter plugs into this
indicate the operating status of the Local and Remote
units (see CE-250R (Remote Unit), p. 11).
Local Unit plugs into this connector.
jack.
AC 9V
REMOTE I /O
6
5
- 8 -
Installation
Setting up the CE-250 KVM Extender system is simply a matter
of plugging in the cables. Refer to the installation diagram on the
following page and do the following:
1. Make sure that all the equipment to be connected up is
powered Off.
2. Plu g the cables from the local console devices (mouse,
keyboard, monitor), into their ports on the Console side of the
Local Unit (CE-250L).
3. Plug the appropriate connectors on the KVM cable supplied
with this unit into the CPU side of the CE-250L. Each
connector is marked with an appropriate icon to indicate
which it is.
Note: The female monitor connector is the one that plugs into
the CE-250L.
4. Plu g the connectors on the other end of the cable into the
appropriate ports on the computer (or Console section of the
KVM switch - if you are using one). Each connector is marked
with an appropriate icon to indicate which it is.
5. Plu g either end of the Category 5 twisted pair cable into the
CE-250L's Remote I/O port.
6. Plu g one of the power adapters (supplied with this package)
into an AC source; plug the adapter's power cable into the
CE-250L's Power Jack
7. Plug the other end of the Category 5 twisted pair cable into
the I/O port of the Remote Unit (CE-250R).
8. Plu g the cables from the remote console devices (mouse,
keyboard, monitor), into their ports on the Console side of the
CE-250R.
9. Plug the second power adapter (supplied with this package)
into an AC source; plug the adapter's power cable into the
CE-250R's Power Jack.
- 9 -
CE-250L
FrontView
CPU
CE-250R
CONSOLE
CE-250L
Rear View
CONSOLE
AC 9V
REMOTE I /O
AC 9V
REMOTE I /O
- 10 -
Operation
The Local and Remote Units each have two LEDs to indicate
their operating status, as shown in the tables, below:
CE-250L (Local Unit)
LED
Local Lights to indicate that
Local Auto
the local console is
active (the Remote
LED is out).
Operating Mode
1. Lights when the local console is active
(the Remote LED is out).
2. Turns off when the remote
console is active (the Remote
LED turns on).
3. Flashes on and off alternately with
the Remote LED when neither
console is active.
Remote The LED is Off 1. Lights when the remote console is
active (the Local LED is out).
2. Turns off when the local console is
active (the Local LED turns on).
3. Flashes on and off alternately with
the Local LED when neither
console is active.
CE-250R (Remote Unit)
LED Indication
Power 1. Lights steadily to indicate that the connection to the
On Line 1. Lights when the remote console is active.
Local Unit is ok.
2. Flashes when there is a problem with the
connection to the Local Unit.
2. Is Off when the local console is ac ti ve .
3. Is Off when there is a problem with the connection to
the Local Unit.
- 11 -
Troubleshooting
Problem Action
No video Make sure that all cables are securely plugged
into their sockets.
Poor video quality. The video quality can be improved by reducing
the refresh rate.
TP Wiring Diagram
PAIR 3
PAIR 2 PAIR 1
123456 78
W-O W-GO G W-Br BrBl W-Bl
JACK POSITIONS
T568B
AT&T 258A
TP Pin Assignments
Pin Assignment
1V OUT B
2/V OUT B
3V OUT G
4V OUT R
5/V OUT R
6/V OUT G
7/DO
8DO
- 12 -
PAIR 4
Specifications
Function CE-250L CE-250R
Connectors Keyboard 2 x 6-pin Mini-DIN F 1 x 6-pin Mini-DIN F
Mouse 2 x 6-pin Mini-DIN F 1 x 6-pin Mini-DIN F
Monitor 1 x HDB-15 M
LEDs 1 x Local 1 x Power On
Function Keys 1 x Local/Auto Select N/A
Cable Length 150m [500'] (max.)
Video Resolution 1280 x 1024; DDC; DDC2; DDC2B
Power Consumption AC 9V, 2.7W (max.) AC 9V, 4.0W (max.)
Housing Plastic
Weight 0.30kg
Dimensions (L x W x H) 13 x 10 x 3.5 cm 10 x 8 x 3.5 cm
1 x HDB-15 F
1 x Remote 1 x On Line
* DDC, DDC2, and DDC2B support is for the Local monitor only.
1 x HDB-15 F
0.22kg
- 13 -
Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT FROM THE DIRECT, INDIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE
OF THE PRODUCT, DISK OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed, implied, or
statutory with respect to the contents or use of this documentation, and specially
disclaims its quality, performance, merchantability, or fitness for any particular
purpose.
The direct vendor also reserves the right to revise or update the device or
documentation without obligation to notify a ny individual or ent ity of such revisions,
or update. For further inquires please contact your direct vendor.
- 14 -
Loading...