Atech Tech LIBRA-04 M User Manual

LIBRA-04 M MANUAL COPY ROUTER

LIBRA-04 M

MANUAL COPY ROUTER

User's Manual

LIBRA-04 M MANUAL COPY ROUTER

TABLE OF CONTENTS

ITEM # SUBJECT PAGE #

I INTRODUCTION 3

II SAFETY APPLICATIONS 4

II.1

II.2 SAFETY INSTRUCTIONS 5

III MACHINE DESCRIPTION 8

III.1 TECHNICAL DESCRIPTION 9

III.2 TECHNICAL DATA 9

IV INSTALLATION 10

IV.1 MACHINE LIFTING AND MOVING 10

IV.2 THE REQUIRED OPERATION ZONE 11

IV.3 INSTALLATION AND ASSEMBLY OF MACHINE 11

V RUNNING THE MACHINE 13

VI MAINTENANCE AND LUBRICATION 14

VII

VII.1

DESCRIPTION OF SYMBOLS USED IN THIS USER’S
MANUAL

TABLE OF PROBABLE PROBLEMS AND THEIR
SOLUTIONS

WHEN PROBLEM OCCURS, THE PROCESSES
THAT SHOULD BE DONE

4

15

15

VIII CIRCUIT DIAGRAMS 17

VIII.1 PNEUMATIC CIRCUIT 17

VIII.2 ELECTRIC CIRCUIT 18

LIBRA-04 M MANUAL COPY ROUTER

I. GENERAL INFORMATION

1.1. INTRODUCTION

The user’s manual given by the manufacturer contains necessary information about
the machine parts. Each machine operator should read these instructions carefully,
and the machine should be operated after fully understanding them.

Safe and efficient use of the machine for long term depends on understanding and
following the instructions contained in this manual. The technical drawings and details
contained in this manual constitute a guide for the operator.

1.2. DISTRIBUTOR

ATech Machine, Inc.
7609-F Airpark Road – Gaithersburg, MD 20879 USA
Phone: [phone] Toll Free: 1-866-80A-TECH Fax: [phone]
Website: www.ATechMachine.com E-mail: [e-mail]

In case of any technical problem please contact your nearest ATECH dealer through
the above mentioned phone, fax or e-mail address.

Technical labels with the model description of the machine are fixed onto the front side
of each machine.

The machine’s serial number and manufacturing year are stipulated on the technical
label.

Before using the Libra-04 M Manual Copy Router read the user’s manual.

3 / 19

LIBRA-04 M MANUAL COPY ROUTER

II – SAFETY APPLICATION

Before operating this equipment, be sure of reading and understanding the safety

instructions.

The operator may not run the machine without reading this guide.

Reading and understanding this user guide is important for hindering to injury to the

operator, third persons, animals, environment and/or damage to the machine.

II.1 – DESCRIPTION OF SYMBOLS USED IN THIS
USER’S MANUAL

This symbol express the definitions to give some information about the machine.

This symbol express that machine does not be operated without reading the user

guide.

This express that security conditions that must be followed to prevent possible

damage to the machine.

In this technical manual all information which effect your safety are marked
with this warning symbol.

Caution!

The caution symbol is always used when there is danger of injury to
persons.

This is hazardous voltage symbol.

This is general warning symbol. This rules must be obeyed.

This shows that attitudes should not be done without being expert.

This symbol indicates that there is a pinch point.

This explains the processes that should be done before maintenance.

4 / 19

LIBRA-04 M MANUAL COPY ROUTER

This explains not be pulled up the protective parts. Do not operate without guards.

This is high temperature symbol.

II.2 – SAFETY INSTRUCTIONS

Before operating this equipment, read the safety instructions and carry out them.

This technical handbook should be accessible at all times at the site of
operation of the machine.

The operators who work during the installation, should read the machine guide.

Be sure of understanding.

User should not intervene to the machine if occurs any failure. Only expert should

repair the machine.

Machine and parts should be protected from the all external defects. Check for

proper oil level before operating machine. If it is insufficient, add up.

Do not stay under machine during loading and discharge.

Never use the machine without grounding. Machine grounding should be made

for two different coupling.

1-) Normal machine grounding.

2-) PLC grounding.

While machine is run or set up for angular cuts, be careful about pinching your

hand to clamping pistons.

When transmission parts of machine abrade, they should be replaced with new

ones.

5 / 19

LIBRA-04 M MANUAL COPY ROUTER

Use only original spare part.

Don’t lean against control panel and do not force.

Use e-Stop button when necessary for stopping the machine because very
frequent repetition of this process, may cause problems on the some electric
components.

Service personnel of our company is responsible from the first operation of
machine. Do not allowed to run the machine any other person.

In the event of the machine failure, if there is a problem about electric, electric
panel should be opened by experts and again eliminated the problem by them.

Do not operate the machine except intended purpose.

---- Don’t touch the cables which are in the machine.

Do not wear clothes that hamper manufacturing and endanger the human safety
while the operator run machine. Never operate the machine when you get alcohol
or drug.

While machine is running, don’t make repairs, adjustments and maintenance.

Never remove protective machine parts on the machines. Do not forget that such
protective machine parts are put in order to protect your security.

Never touch the heaters of machine.

Only one person should operate the machine.

Before the machine stops don’t open the safety covers.

6 / 19