Page 1
PMM 9010F
FFT Time Domain Digital EMI Receiver
& Real time Analyzer
FFT-based, gapless EMI receiver & Analyzer, 10 Hz – 30 MHz
Full compliance to CISPR 16-1-1
Reduces test time from hours to seconds
Real-time spectrum analysis
Rugged, light weight, small size, internal battery for best portability
User-friendly in stand-alone and with the powerful PMM Emission Suite
Expandable to higher frequencies
Page 2
PMM 9010F
Applications
Measurement of conducted and radiated emissions of EUT in full compliance to CISPR, IEC-EN standards.
Analyzing the emissions in short time is particularly suitable for EUT with short operation cycles, e.g. electric tools, food machinery and in general all appliances with electric motors subjected to over-heating if run for too long time.
Fast and reliable tests provide the designer of an immediate feedback in the try-and-test process, an effective contribution to
reduce the product time-to-market.
Description
The new EMI Receiver PMM 9010F is based on very advanced analog to digital conversion and data processing technology that
applies the FFT frequency spectrum analysis in full compliance with all the tests required by the standard CISPR 16-1-1.
Same modular construction, compact size and low power consumption of the other renowned models in PMM’s Digital Receiv-
ers family: PMM 9010, 9010/03P, 9010/30P.
Measurement speed
CISPR detectors as the Q-Peak, C-RMS and C-AVG detectors are characterized by a long settling time: measurements must be
performed with a long observation time (hold time) of 1 - 2 seconds for each frequency step; setting hold times lower than 1s
can reduce the test time but at the cost of possible severe errors and under-estimation of the levels.
PMM 9010F overcomes this limitation by scanning the entire spectrum in less than 25 seconds with hold time of 1 second and
for all detectors, instead of nearly 5 hours (*).
Such methods for reducing the test time e.g. pre-testing, Smart Detectors and Frequency Tables are no more needed.
Noise and sensitivity
PMM 9010F’s very advanced design provides outstanding performances not only in terms of measurement speed, but also in
terms of noise floor level.
In a typical conducted emissions test configuration:
- Hold time: 1 s
- Detector: QP
- Preselector: ON - Preamplifier OFF
the noise floor is less than -7 dBµV in the band A (9 – 150 kHz) and 5 dBµV in the band B (0,15 – 30 MHz), corresponding
to less than -137 and -141 dBm/Hz respectively.
When a higher sensitivity is required, the internal preamplifier reduces the noise floor to less than -24 dBµV in band A, and -7
dBµV in band B, corresponding to less than -154 dBm/Hz in both cases.
Analyzer mode
The Analyzer mode is particularly useful in EUT development, and is even faster: it features real-time spectrum analysis over a
full span of 30 MHz (RBW 300 kHz) or 1,84 MHz (RBW 9 kHz CISPR).
PMM Emission Suite (PES)
Easy, user-friendly, always updated PC software supplied with the PMM 9010F for real-time measurements, save, recall and edit
settings, factors, limits, scans etc. Specific functions automatize the measurements. Reporting and data import-export included.
Ancillaries
PMM 9010F together with the PES drives all the PMM ancillaries like LISN and RF switches.
Implementations and upgrading
Like all the models of the family, the PMM 9010F can be expanded in frequency - up to 18 GHz - and added of the options very
easily and safely by the user itself. Details provided in the last page.
Service
Designed having in mind the EMC real world, PMM receivers are very difficult to damage. Should the case, immediate and effective support is provided by the International Sales Network.
Calibration
Almost all of the receiver is calibration-free, lifetime. The internal reference provides for auto-calibrating RF front-end - attenuators, preselector, preamplifier - and A/D conversion. Accredited calibration certificate available (option).
(*) Considering a frequency step of 1/4 RBW
Page 3
Page 4
Ordering information
9010F
EMI receiver 10 Hz - 30 MHz CISPR 16-1-1 full-compliance
Including:
- internal generator 10 Hz – 30 MHz - RS232/USB adapter
- AC adapter (mod. 9010/AC) - N-BNC adapter
- PC software PMM Emission Suite - Control cables (USB, RS-232), BNC-BNC cable
- Standard Calibration Certificate
Optional accessories and functions
9010/MIL (*)
9010/RAV
9010/CLICK (*)
9010/BTA
MIL-STD-461 RBW Filters
CISPR RMS-AVG detector
Click Analyzer function, CISPR 14-1 full-compliance, including:
- Switching Operation Box, control cables
- 2x20 dB attenuator
RS-232 to BlueTooth adapter for 9010
BP01
9010/AC
9010/CC
Li-Ion Battery Pack
Additional AC adapter/charger for BP01 (one already supplied with 9010F)
Rigid carrying case
9010/UKAS UKAS CISPR-16-1-1 accredited calibration certificate for Bands A, B (9 kHz - 30 MHz)
9010/UKAS-Click UKAS accredited calibration certificate for 9010F + 9010/Click to CISPR-16-1-1 & CISPR-14-1
Frequency upgrades (*)
9030 Extension unit 30 MHz - 3 GHz, full compliant to CISPR 16-1-1 (UKAS accredited calibration on option)
9060 Extension unit 30 MHz - 6 GHz, full compliant to CISPR 16-1-1 (UKAS accredited calibration on option)
9180 Extension unit 6 – 18 GHz, full compliant to CISPR 16-1-1 (UKAS accredited calibration on option)
Ancillary equipments
LISN - controlled by the PMM 9010F receiver to automatically select the lines to measure
• L1-150M Single line LISN, 150A • L3-64 Four lines, 3-phase, 64A LISN
• L2-16A Two lines, Single phase, 16A LISN • L3-100 Four lines, 3-phase, 100A LISN
• L3-32 Four lines, 3-phase, 32A LISN • L3-500 Four lines, 3-phase, 350A LISN
CISPR 16-1-2 Voltage Probes
• SHC-1/1000 35 dB CISPR, 1500 ? , 1 kV • SHC-2 30 dB CISPR, 1500 ? , 300 V
Antennas
• RA-01 Rod Antenna 9 kHz – 30 MHz • LP-02 Log Periodic Antenna 200 MHz - 3 GHz
• BC-01 Biconical Antenna 30-200 MHz • LP-03 Log Periodic Antenna 800 MHz - 6 GHz
• DR-01 Double-ridged Antenna 6 -18 GHz • TR-01 Tripod for PMM Antennas
EN55015 (CISPR 15) components
F-300M-16 CDN 150 kHz - 300 MHz; 250 VAC - 16A, 50/60 Hz for power circuitry testing with phase, neutral and PE
RF-300 3-axis Loop Antenna System for CISPR 15 EN55015
RF-300C Calibration kit for RF-300
TRF-1 Balance/unbalance transformer
DL-xx Dummy Lamps according to the Standard
VDH-01 Van der Hoofden test-head for IEC 62493 (human exposure to emf generated by lighting equipment)
(*) Functions under development, field-installable by user
Narda Safety Test Solutions Srl
Via Leonardo da Vinci, 21/23
20090 Segrate (Milano) - ITALY
Phone.: +39 02 269987-1
Fax: +39 02 269987-00
E-Mail: support@narda-sts.it
Internet: www.narda-sts.it
Specifications subjected to changes without prior notice 03/12
Loading...