Atec MX User Manual

California Instruments MX Series II
www.tti.co.uk
Tel: 01480 412451
15–135 kVA
Overview
High Power AC and DC Power Source Programmable AC and DC power for frequency conversion and product test applications
Expandable Power Levels Available output power of 15, 30, and 45 kVA per unit and multi-unit congurations for power requirements up to 135 kVA and above
Single and Three Phase Mode Phase mode programming on MX30-3Pi and MX45-3Pi allows switching between single and three phase output modes
Arbitrary & Harmonic Waveform Generation User dened voltage waveform and distortion programming
Multiple Voltage Ranges Available 150, 300 or 400 Volt ranges in AC mode and 200 or 400 Volt ranges in DC mode
High RMS Current Maximum current of 125 A rms (MX15), 250 A rms (MX30), and 375 A rms (MX45)
Remote Control Standard RS232C & USB along with optional IEEE­488 & LAN Interfaces are available for automated test applications
Introduction
The MX Series consists of multiple high power AC and DC power systems that provide controlled AC and DC output for ATE and product test applications.
This high power AC and DC test system covers a wide spectrum of AC and DC power applications at an affordable cost. Using state-of-the-art PWM switching techniques, the MX series combines compactness, robustness and functionality in a compact oor-standing chassis, no larger than a typical ofce copying machine. This higher power density has been accomplished without the need to resort to elaborate cooling schemes or additional installation wiring. Simply roll the MX15, MX30, or MX45 unit to its designated location (using included casters), plug it in, and the MX series is ready to work for you.
150–400 V
0–375 A / Phase
208 230 400
480
Simple Operation
The MX Series can be operated completely from its menu driven front panel controller. A backlit LCD display shows menus, setup data, and read-back measurements. IEEE-488, RS232C, USB and LAN remote control interfaces and instrument drivers for popular ATE programming environments are available. This allows the MX Series to be easily integrated into an automated test system.
For advanced test applications, the programmable controller version offers full arbitrary waveform generation, time and frequency domain measurements, and voltage and current waveform capture.
Congurations
The MX15 delivers up to 15 kVA of single phase output. The MX30 delivers up to 30 kVA, and the MX45 up to 45 kVA. Both operate using single or three phase output in AC mode. In DC mode, 65 % of the AC power level is available. On MX-P models, AC+DC mode is also supported.
For higher power requirements, the MX90 and MX135 models are available. Multi cabinet MX45 systems always operate in three phase output mode. Available recongurable MX90 and MX135 models (-MB designation) provide multiple controllers which allow separation of the high power system into two or three individual MX45 units for use in separate applications. This ability to recongure the system provides an even greater level of exibility not commonly found in power systems.
858.458.0223
sales@ProgrammablePower.com 217
MX Series II
Product Evaluation and Test
Increasingly, manufacturers of high power equipment and appliances are required to fully evaluate and test their products over a wide range of input line conditions. The built-in output transient generation and read-back measurement capability of the MX Series offers the convenience of a powerful, and easy to use, integrated test system.
Avionics
With an output frequency range to 819 Hz (or 1000 Hz with -HF option), the MX Series is well suited for aerospace applications. Precise frequency control and accurate load regulation are key requirements in these applications. The available IEEE-488 remote control interface and SCPI command language provide for easy integration into existing ATE systems. The MX Series eliminates the need for several additional pieces of test equipment, saving cost and space. Instrument drivers for popular programming environments such as National Instruments LabView™ are available to speed up system integration.
Regulatory Testing
As governments are moving to enforce product quality standards, regulatory compliance testing is becoming a requirement for a growing number of manufacturers. The MX Series is designed to meet AC source requirements for use in compliance testing such as IEC 61000, 3-2, 3-3, 3-11, 3-12, to name a few.
Choice of voltage ranges
The MX30 and MX45 can be ordered with either a 150 V RMS Line to Neutral output voltage range or a 300 V RMS Line to Neutral range. This provides 3 phase output capability of 260 Vac or 520 Vac line to line respectively. If dual output ranges are required, the programmable range change option (-R) provides the ability to switch between both output ranges. Pi version models offer standard dual voltage ranges.
The DC output mode changes the 150 V AC range to a 200 V DC output range; the 300 V AC range becomes 400 V DC.
For applications requiring more than 300 V L-N (or 520 V L-L), the optional -HV output transformer provides an additional 400 V L-N and 693 V L-L output range for use in AC mode only.
Multi-Box Congurations
For high power applications, two or three MX45 chassis can be combined to provide 90 to 135 kVA of three phase power. MX90 and
MX135 systems are always congured for three phase operation. Contact sales for custom congurations.
High Crest Factor
With a crest factor of up to 3.6, the MX Series AC source can drive difcult nonlinear loads with ease. Since many modern products use switching power supplies, they have a tendency to pull high repetitive peak currents. The MX30-3Pi can deliverup to 240 Amps of repetitive peak current (150 V AC range) per phase to handle three phase loads. The MX45-3Pi can deliver up to 360 Amps. 720 Amps (MX30), and 1080 Amps (single phase mode).
Remote Control
Standard RS232C & USB along with optional IEEE-488 & LAN
programming of all instrument functions from an external computer. The popular SCPI command protocol is used for programming.
Application Software
Windows® application software is included with both versions. This software provides easy access to the power source’s capabilities without the need to develop any custom code. The following functions are available through this GUI program:
• Steady state output control (all parameters)
• Create, run, save, reload and print
transient programs
• Generate and save harmonic waveforms. [Pi only]
• Generate and save arbitrary waveforms. [Pi only]
• Measure and log standard measurements
• Capture and display output voltage and
current waveforms. [Pi only]
• Measure, display, print and log harmonic
voltage and current measurements. [Pi only]
• Display IEEE-488, RS232C, USB and LAN bus
trafc to and from the AC Source to help you develop your own test programs.
1. Requires PC running WindowsXP™ or Windows 2000™.
remote control interfaces allow
www.ProgrammablePower.com218
MX Series II
15–135 kVA
Harmonic Waveform Generation [Pi controller]
Using the latest DSP technology, the MX Series programmable controller is capable of generating harmonic waveforms to test for harmonics susceptibility. The Windows Graphical User Interface program can be used to dene harmonic waveforms by specifying amplitude and phase for up to 50 harmonics. The waveform data points are generated and downloaded by the GUI to the AC source through the IEEE-488 or RS232C bus. Up to 200 waveforms can be stored in nonvolatile memory and given a user dened name for easy recall.
All MX-Pi Series congurations offer three phase waveform generation, allowing independent phase anomalies to be programmed. It also allows simulation of unbalanced harmonic line conditions.
Harmonic waveform, Fund., 3rd, 5th, 7th, 9th,11th and 13th.
Two hundred user dened waveforms.
MX Series - AC and DC Transient Generation
The MX Series controller has a powerful AC and DC transient generation system that allows complex sequences of voltage, frequency and waveshapes to be generated. This further enhances the MX’s capability to simulate AC line conditions or DC disturbances. When combined with the multiphase arbitrary waveform capabilities, the AC and DC output possibilities are truly exceptional. Transient generation is controlled independently yet time synchronized on all three phases. Accurate phase angle control and synchronized transient list execution provide unparalleled accuracy in positioning AC output events.
Transient programming is easily accomplished from the front panel where clearly laid out menu’s guide the user through the transient denition process.
The front panel provides a convenient listing of the programmed transient sequence and allows for transient execution Start, Stop, Abort and Resume operations. User dened transient sequences can be saved to non-volatile memory for instant recall and execution at a later time. The included Graphical User Interface program supports transient denitions using a spreadsheet-like data entry grid. A library of frequently used transient programs can be created on disk using this GUI program.
Arbitrary Waveform Generation
Using the provided GUI program or custom software, the user also has the ability to dene arbitrary AC waveforms. The arbitrary waveform method of data entry provides an alternative method of specifying AC anomalies by providing specic waveform data points. The GUI program provides a catalog of custom waveforms and also allows real-world waveforms captured on a digital oscilloscope to be downloaded to one of the many AC source’s waveform memories. Arbitrary waveform capability is a exible way of simulating the effect of real-world AC power line conditions on a unit under test in both engineering and production environments.
Harmonically distorted waveform.
Transient List Data Entry from the front panel.
Transient List Data Entry in GUI program.
858.458.0223
sales@ProgrammablePower.com 219
MX Series II
MX Series - Measurement and Analysis
The MX Series is much more than a programmable AC, DC or AC+DC power source. It also incorporates an advanced digital signal processor based data acquisition system that continuously monitors all AC source and load parameters. This data acquisition system forms the basis for all measurement and analysis functions. These functions are accessible from the front panel and the remote control interface for the MX Series (MX15 excluded; uses 2-line display shown below).
2-line display for the MX15.
Conventional Measurements [All controllers]
Common AC and DC measurement parameters are automatically provided by the data acquisition system. These values are displayed in numeric form on the front panel LCD display. The following measurements are available: Frequency, Vrms, Irms, Ipk, Crest Factor, Real Power (Watts), Apparent Power (VA) and Power Factor.
Harmonic Analysis [Pi controller]
The MX Series provides detailed amplitude and phase information on up to 50 harmonics of the fundamental voltage and current (up to 16 kHz in three phase mode) for either one or three phases. Harmonic content can be displayed in both tabular and graphical formats on the front panel LCD for immediate feedback to the operator (excluding MX15). Alternatively, the included GUI program can be used to display, print and save harmonic measurement data. Total harmonic distortion of both voltage and current is calculated from the harmonic data.
Waveform Acquisition [Pi controller]
The measurement system is based on real-time digitization of the voltage and current waveforms using a 4K deep sample buffer. This time domain information provides detailed information on both voltage and current waveshapes. Waveform acquisitions can be triggered at a specic phase angle or from a transient program to allow precise positioning of the captured waveform with respect to the AC source output.
The front panel LCD displays captured waveforms with cursor readouts (excluding MX15). The included GUI program also allows acquired waveform data to be displayed, printed, and saved to disk.
Acquired Current waveform (MX30/45 Display).
Acquired Voltage waveform (MX30/45 Display).
Measurement data for single phase (MX30/45 Display).
Measurement data for all three phases (MX30/45 Display).
Absolute amplitude bar graph display of current harmonics with cursor positioned at the fundamental (MX30/45 Display).
Voltage harmonic measurement table display in absolute values (MX30/45 Display)
www.ProgrammablePower.com220
Acquired three phase voltage waveforms display on PC.
MX Series II : Specications
Current
(RMS)
Voltage (RMS)
Full
Power
15–135 kVA
Operating Modes
Standard AC or DC
Pi Version AC, DC and AC+DC
AC Mode Output
Frequency Range: 16.00-819.0 Hz, -LF Option: 16.00-500.0 Hz, -HF Option: 16.00-1000 Hz (supplemental specications apply above
Phase Outputs MX15-1/15-1Pi: 1, MX30/45-3Pi: 1 or 3 switchable, Neutral: Floating, Coupling: DC (except for -HV option)
Total Power MX15-1/1Pi: 15 kVA, MX30-1/3: 30 kVA, MX45-1/3: 45 kVA, MX90: 90 kVA, MX135: 135 kVA
Load Power Factor 0 to unity at full output current
819 Hz). Resolution: 0.01 Hz: 16.00 - 81.91 Hz, 0.1 Hz: 82.0 Hz - 819.1 Hz, 1 Hz: 820-1000 Hz
AC Mode Voltage
Voltage Ranges
External Sense Voltage drop compensation (5% Full Scale)
Harmonic Distortion (Linear) Less than 0.5% from 16 - 66 Hz, Less than 1% from 66 - 500 Hz, Less than 1.25% above 500 Hz
DC Offset < 20 mV
Load Regulation 0.25% FS @ DC - 100 Hz, 0.5% FS > 100 Hz
External Amplitude Modulation Depth: 0 - 10 %, Frequency: DC - 2 KHz
Voltage slew rate 200 µs for 10% to 90% of full scale change into resistive load
Range V Low V High Load Regulation < 0.25 % FS DC to 100 Hz, < 0.5 % FS 100 Hz to 819 Hz AC 0-150 V 0-300 V Line Regulation < 0.1% FS for 10 % line change AC+DC 0-150 V 0-300 V
AC Mode Current
Steady State AC Current @ FS V
Model MX15-1 MX15-1Pi MX30-1 MX30-3 MX30-3Pi / 1Pi MX45-1 MX45-3 MX45-3Pi / 1Pi MX90-3/Pi MX135-3/Pi
V Low 100 100 200 66.6/ø 66.6/ø / 200 300 100/ø 100/ø / 300 200/ø 300/ø
V High 50 50 100 33.3/ø 33.3/ø / 100 150 50/ø 50/ø / 150 100/ø 150/ø
Note: Constant power mode provides increased current at reduced voltage. See chart below
Peak Repetitive AC Current Up to 3.6 x rms current at full scale voltage
Programming Accuracy Voltage (rms): ± 0.3 Vrms, Frequency: ± 0.01 % of programmed value, Current Limit: - 0 % to + 5 % of programmed value + 1A, Phase:
Programming Resolution Voltage (rms): 100 mV, Frequency: 0.01 Hz from 16 - 81.91 Hz, 0.1 Hz from 82.0 - 819 Hz, Current Limit: 0.1 A, 3 phase mode,
< 0.5° + 0.2°/ 100 Hz with balanced load
1.0 A, 1 phase mode, Phase: 0.1°
Constant Power AC Mode - Available Max. AC Current
125%
100%
50%
20%
10% 80%
50%
100%
Note: Specications are subject to change without notice. Specications are warranted over an ambient temperature range of 25°± 5° C. Unless otherwise noted, specications are per phase
for a sinewave with a resistive load and apply after a 30 minute warm-up period. For three phase congurations, all specications are for L-N. Phase angle specications are valid under balanced load conditions only.
© 2009 AMETEK Programmable Power All rights reserved. AMETEK Programmable Power is the trademark of AMETEK Inc., registered in the U.S. and other countries. Elgar, Sorensen,
California Instruments, and Power Ten are trademarks of AMETEK Inc., registered in the U.S.
858.458.0223
sales@ProgrammablePower.com 221
MX Series II : Specications
Measurement
Measurements - Standard (AC Measurements)
Parameter Frequency RMS
Range 16-100 Hz
Accuracy*
Resolution* 0.01 Hz /
* Measurement system bandwidth = DC to 6.7 kHz. Accuracy specications are valid above 100 counts. Current and Power Accuracy and Range specications are
100-820 Hz
0.01% +
(±)
times three for MX90, MX135 or MX30/45-3Pi in single phase mode. PF accuracy applies for PF > 0.5 and VA > 50 % of range
Voltage 0-400 V 0-160 A 0-400 A 0.00-6.00 0-15 kW 0-15 kVA 0.00-1.00 0.0-360.0 0-400 V 0-160 A Power
0.05 V +
0.01 Hz
0.1 Hz
0.02%
0.1 V +
0.02%
10 mV 10 mA 10 mA 0.01 10 W 10 VA 0.01 0.1° 10 mV 10 mA 10 W
RMS Current
0.15 A + .02%
0.3 A +
0.02%
Peak Current
0.15 A +
0.02%
0.3 A +
0.02%
Crest Factor
0.05
0.05
Real Power
30 W +
0.1%
60 W +
0.1%
Apparent Power
30 VA +
0.1%
60 VA +
0.1%
Power Factor
0.01
0.02
Phase DC
VoltageDCCurrent
2.0°
0.5 V 0.5 A 0.15 kW
3.0°
Power
Measurements - Harmonics (Pi controller only)
Parameter Frequency Fundamental Harmonics Phase Voltage Current
Range 16.00-1000.0 Hz / 32.00 Hz - 16 kHz 0.0 - 360.0° Fundamental Harmonics 2-50 Fundamental Harmonics 2-50
Accuracy* (±) 0.03% + 0.03 Hz / 0.01 Hz 2° typ. 750 mV 0.3% + 750 mV+0.3% /1 kHz 0.5 A / 0.3% + 150 mA +0.3% /1 kHz
Resolution 0.01 Hz 0.5° 10 mV / 10 mV 100 mA / 100 mA
* Accuracy specications are valid above 100 counts. Accuracy specications are for three phase mode. Harmonics frequency range for MX30/45-3Pi in single phase
mode is 32 Hz - 48 kHz
DC Mode Output
Power Maximum DC power at full scale of DC voltage range. MX15-1Pi: (10 kW), MX30-3Pi: (6.5 kW per output, 3 outputs. 20 kW in
Voltage Ranges Range: Low (0 - 200 V), High (0 - 400 V)
Output Accuracy ± 1 Vdc
Load Regulation < 0.25 % FS
Line Regulation < 0.1% FS or 10 % line change
Ripple < 2 Vrms Lo Range, < 3 Vrms Hi Range
Max DC Current @ FSV per output
Current Limit Programmable from 0 A to max. current for selected range
1 channel mode), MX45-3Pi: (10 kW per output, 3 outputs. 30 kW in 1 channel mode)
Model MX15-1 MX15-1Pi MX30-1 MX30-3 MX30-3Pi / 1Phs MX45-1 MX45-3 MX45-3Pi / 1Phs MX90-3/Pi MX135-3/Pi V Low 50 50 200 66.7 33.3 / 100 150 50 50 / 150 100 150 V High 25 25 100 16.6 16.6 / 50 75 25 25 / 75 50 75
Note: Constant power mode provides increased current at reduced voltage. See chart on previous page
AC+DC Mode Output
Output (Pi) Power Maximum current and power in AC+DC mode is same as DC mode
Protection
Over Load Constant Current or Constant Voltage mode
Over Temperature Automatic shutdown
Storage
Non Volatile Mem. storage 16 instrument setups, 200 user dened waveforms [Pi only]
Waveforms
Waveform Types Std: Sine, Pi: Sine, Square, Clipped sine, User dened
User dened waveform storage (Pi version) Four groups of 50 user dened arbitrary waveforms of 1024 points for a total of 200. One group can be active at a time
System Interface
Inputs Remote shutdown, External Sync, Clock/Lock (option on Pi)
Outputs Function Strobe / Trigger out, Clock/Lock (option on Pi)
Remote Control (Pi standard with -P option)
IEEE-488 Interface IEEE-488 (GPIB) talker listener. Subset: AH1, C0, DC1, DT1, L3, PP0, RL2, SH1, SR1, T6, IEEE-488.2 SCPI Syntax
RS232C Interface 9 pin D-shell connector (Supplied with RS232C cable)
LAN Ethernet Interface: 10BaseT, 100BaseT, RJ45
USB Version: USB 1.1; Speed: 460 Kb/s maximum
Output Relay Push button controlled or bus controlled output relay
Output impedance Programmable Z available on MX30-3Pi and MX45-3Pi in 3 phase mode only. Specications apply at 50 Hz fundamental.
Resistive: 1 - 200 mOhm, Inductive: 15 - 200 uH
www.ProgrammablePower.com222
MX Series II : Specications
15–135 kVA
AC Input
Voltage Must be specied at time of order. All inputs are L-L, 3ø, 3 wire + Gnd. 208 ± 10% VAC, 230 ± 10% VAC, 400 ± 10% VAC,
Input Line Current (per phase)
Line Frequency 47 - 63 Hz
Efciency 85 % typical
Power Factor 0.95 typical
480 ± 10% VAC
Current (MX15): Current (MX30/45): V L-L 208 230 400 480 V L-L 208 230 400 480 St State 58.3 ARMS 52.3 ARMS 30 ARMS 25 ARMS St State 116/175 ARMS 105/157 ARMS 60/90 ARMS 50/75 ARMS
Distortion: < 8 % at full power < 20 % below 35 % of power
AC Service
Inputs/Outputs MX30/MX45: Front access, cables routed through rear panel, exit in back. MX15: Rear Access
Regulatory IEC61010, EN50081-2, EN50082-2, CE EMC and Safety Mark requirements
EMI CISPR 11, Group1 , Class A
Connectors AC Input & Output terminal block behind front cover, IEEE-488 (GPIB) connector (rear panel), 9 pin D-Shell RS232C connector*, (rear
panel), Remote voltage sense terminal block (rear panel), System Interface Connector, DB-37 (rear panel). *RS232 DB9 to DB9 cable supplied
Physical Dimensions
MX30/MX45 Dimensions Height: 50.0” (1270 mm), Width: 28.75” (731 mm), Depth: 34.5” (876 mm)
MX30/MX45 Weight Chassis: Net: 1150 lbs / 522 Kg, Shipping: 1231 lbs / 560 Kg, Amp Module: Net: 63 lbs / 29 Kg
MX15 Dimensions Height: 31.75” (806 mm), Width: 24.0” (610 mm), Depth: 28.0” (711 mm)
MX15 Weight Chassis: Net: 600 lbs / 272 Kg, Shipping: 681 lbs / 309 Kg, Amp Module: Net: 63 lbs / 29 Kg
Chassis MX30/MX45: Casters and forklift openings. MX15: Casters
Vibration and Shock Designed to meet NSTA project 1A transportation levels. Units are shipped in wooden crate with forklift slots
Air Intake/Exhaust Forced air cooling, front air intake, rear exhaust
Operating Humidity 0 to 95 % RAH, non condensing
Temperature Operating: 0 to 40° C (30° C max in CP mode), Storage: -20 to +85° C
Standard controller versions with single voltage range
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX15-1 15 kVA 1 150/200 or 300/400 Standard
MX30-1 30 kVA 1 150/200 or 300/400 Standard
MX30-3 30 kVA 3 150/200 or 300/400 Standard
MX45-1 45 kVA 1 150/200 or 300/400 Standard
MX45-3 45 kVA 3 150/200 or 300/400 Standard
MX90-3 90 kVA 3 150/200 or 300/400 Standard
MX135-3 135 kVA 3 150/200 or 300/400 Standard
Programmable controller versions with dual voltage ranges
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX15-1Pi 15kVA 1 150/200 & 300/400 Programmable
MX30-3Pi 30 kVA 1 & 3 150/200 & 300/400 Programmable
MX45-3Pi 45 kVA 1 & 3 150/200 & 300/400 Programmable
MX90-3Pi 90 kVA 3 150/200 & 300/400 Programmable
MX135-3Pi 135 kVA 3 150/200 & 300/400 Programmable
Pi models include IEEE-488, RS232C & USB interfaces, Advanced measurements, arbitrary waveform generation. Phase mode switching on MX-30/45-3Pi.
Programmable controller versions with dual voltage ranges
Model AC Output Power Phase Outputs AC/DC Voltage Range Controller
MX90-3Pi-MB 90 kVA 3 150/200 & 300/400 Dual MX45-3Pi
MX135-3Pi-MB 135 kVA 3 150/200 & 300/400 Triple MX-45-3Pi
Recongurable systems can be separated into stand-alone MX45-3Pi models or combined for higher power levels.
858.458.0223
sales@ProgrammablePower.com 223
MX Series
www.tti.co.uk
Tel: 01480 412451
Available from:
Thurlby Thandar Instruments Ltd. Glebe Road, Huntingdon, Cambs. PE29 7DR U.K. Tel: 01480 412451 e-mail: sales@tti.co.uk Web: www.tti.co.uk
Model
Refer to table shown for model numbers and congurations.
Supplied with
Standard: User Manual on CD ROM. Pi version: User/Programming Manual and Software on CD ROM. RS232C serial cable.
Input Voltage Settings
Specify input voltage (L-L) setting for each MX system at time of order: 208 Congured for 208 V ±10 % L-L, 4 wire input. 230 Congured for 230 V ±10 % L-L, 4 wire input. 400 Congured for 400 V ±10 % L-L, 4 wire input. 480 Congured for 480 V ±10 % L-L, 4 wire input
Standard Model Options
Specify output range on standard models. All range values shown are Line to Neutral.
- 150 Congured for 150 V AC and 200 V DC output ranges.
- 300 Congured for 300 V AC and 400 V DC output ranges.
- LF Limits maximum frequency to 500 Hz.
- P IEEE-488 & RS232C Interface Adds programming, Windows & RS232 Cable.
-LAN Ethernet Interface.
- HF Increases max frequency to 1000 Hz.
- R Range change. Provides 150/200 & 300/ 400 AC/DC output ranges. (Std. MX15)
Pi Model Options
-160 RTCA/DO-160D, DO-160E, and EUROCAE test rmware.
-411 *IEC 1000-4-11 test rmware.
-413 *IEC 1000-4-13 Harmonics & Interharmonics test rmware.
-704 Mil Std 704 A - F test - rmware/ software.
-ABD ABD0100.1.8 Test Option.
-AMD Airbus AMD24 Test
-A350 Airbus Test Software
-B787 Boeing 787 Test Software
-HV Adds 400 V L-N AC-only output range.
-LF Limits max. frequency to 500 Hz.
-HF Increases max. frequency to 1000 Hz.
-XV Adds other AC-only output range. Consult factory.
-LKM Clock/Lock Master
-LKS Clock/Lock Auxiliary
-WHM Watt-Hour Measurement option.
Packaging and Shipment
All MX systems are packaged in re-usable protective wooden crates for shipment.
Feature Comparison
Model STD Pi
AC mode X X
DC mode X X
AC+DC mode X
Dual V Range Option
(Std / MX15)
Transient programming X X
Arbitrary waveforms X
Measurements X X
Harmonic measurements X
Waveform acquisition X
1 or 3 Phase mode MX30/45-3Pi
IEEE / RS232 Option X
X
MX15 Dimensions - single chassis
Rear View
28.00
[711.20]
31.75
[806.45]
[609.80]
Front View
24.00
MX30/MX45 Dimensions - single chassis
28.75
[730.25]
Rear View Front View
www.ProgrammablePower.com224
48.125
[1222.4]
1.95
[49.53]
Loading...