Atec iX User Manual

California Instruments i/iX Series II

3000–15000 VA

General purpose AC power sources

• Combination AC and DC Power Source
and Power Analyzer

• 3000 VA - 15000 VA of Output Power

• Arbitrary Waveform Generation

• Built-in Digital Power Analyzer

• Scope Capture Capability

• EN61000-3-2 and EN61000-3-3

• Powerful Programing Software

• Constant Power Mode

Intergrated System
The iX Series II represents a new generation of AC
and DC power source that addresses increasing
demands on test equipment to perform more
functions at a lower cost. By combining a exible
AC/DC power source with a high performance
power analyzer, the iX Series II systems are
capable of handling complex applications that
have traditionally required multiple instruments.

The sleek integrated approach of the iX Series
II avoids the cable clutter that is commonly
found in AC test systems. The i/iX Series II is
rackmountable with a 4U chassis design. All
connections are made internally and the need for
external digital multimeters, power harmonics
analyzer and current shunts or clamps is
completely eliminated.

Using a state of the art digital signal processor in
conjunction with precision high resolution A/D
converters, the iX Series II provides more accuracy
and resolution than can be found in some
dedicated harmonic power analyzers. Since many
components in the iX Series II are shared between
the AC/DC source and the power analyzer, the
total cost of the integrated system is less than the
typical cost of a multiple unit system.

For less demanding applications, the i Series II
provides similar output and transient capabilities
as the iX Series II, as well as basic measurements.

Easy To Use Controls
Both the iX Series II and i Series II are
microprocessor controlled and can be operated
from an easy to use front panel keypad. Functions
are grouped logically and are directly accessible
from the keypad. This eliminates the need to
search through various levels of menus and/or
soft keys. A large analog control knob can be
used to quickly slew output parameters. This

knob is controlled by a dynamic rate change
algorithm that combines the benets of precise
control over small parameter changes with quick
sweeps through the entire range.

Applications
With precise output regulation and accuracy,
the iX Series II AC and DC sources address
many application areas for AC and DC power
testing. The iX also provides a high load current
capability, multi or single phase output modes,
and built-in power analyzer measurements.
Additional features including line distortion
simulation (LDS), arbitrary waveform generation,
and programmable output impedance address
requirements for product quality and regulatory
compliance testing.

Product Evaluation and Test
Increasingly, manufacturers of electronic
equipment and appliances are required to fully
evaluate and test their products over a wide
range of input line conditions. The built-in output
transient generation and readback measurement
capability offers the convenience of an easy to
use and integrated test system.

Avionics
With an output frequency range to 1000 Hz,
up to 150 VRMS, the iX Series II is well suited
for aerospace applications. Precise frequency
control and accurate load regulation are key
requirements in these applications. The standard
IEEE-488 control interface and SCPI command
language provide for easy integration into existing
ATE systems. Since the iX Series II can eliminate
the need for additional pieces of test equipment
and only occupies 7 inches of rack space (4U),
it signicantly saves cost and space. Options are
available for popular avionics test routines such
as: DO-160, ABD- 0100, MIL-STD-704A-F, Boeing
7E73B-0147, and Airbus test routines.

150–300 V

0–120 A

208 230 400

208 230

858.458.0223

[e-mail] 169

i/iX Series II

Regulatory Testing

As governments are moving to enforce product
quality standards, regulatory compliance testing
is becoming a requirement for a growing
number of manufacturers. The iX Series II is
designed to meet AC source requirements for
use in Euronorm EN 61000 compliance testing.
For icker testing, the programmable output
impedance capability of the 3001iX, 5001iX
and 15003iX can be used to create the required
IEC 725 reference impedance. Run IEC61000­4-11, IEC61000-4-14 and IEC61000-4-28 test
programs.

Multi-Box Congurations
For high power applications, two or three 5001i/
iX chassis can be combined to provide 10 to 15
kVA of single or three phase power. A 9003iX,
15003iX or 15003i three phase conguration can
be ordered with the MODE-iX option. This option
allows automatic switching between single or
three phase output mode. In single phase mode,
all current is available on phase A.

High Crest Factor
With a crest factor of up to 5:1, the i/iX Series II
AC source can drive difcult nonlinear loads with
ease. Since many modern products use switching
power supplies, they have a tendency to pull high
repetitive peak currents. The 5001iX can deliver
up to 110 Amps of repetitive peak current to
handle such loads.

Remote Control
Standard IEEE-488 and RS232C remote control
interfaces allow programming of all instrument
functions from an external computer. The
popular SCPI command protocol is used for
programming. Drivers for several popular
instrumentation programming environments
are available to facilitate systems integration of
the i/iX Series II. Instrument drivers for popular
programming environments such as National
Instruments LabView™ are available to speed up
system intergration.`

Application Software
Windows® application software is included with
the iX and i Series II¹ . This software provides
easy access to the power source’s capabilities
without the need to develop any custom code.
The following functions are available through this
GUI program:

• Steady state output control (all parameters)

• Create, run, save, reload and print

transient programs

• Generate and save harmonic
waveforms [iX only]

• Generate and save arbitrary waveforms [iX only]

• Download data from a digital storage

oscilloscope [iX only]

• Measure and log standard measurements

• Capture and display output voltage and

current waveforms [iX only]

• Measure, display, print and log harmonic
voltage and current measurements [iX only]

• Display IEEE-488 or RS232C bus trafc to
and from the AC Source to help you develop
your own test programs..

1. Requires PC running WindowsXP™ or Windows 2000™

www.ProgrammablePower.com170

i/iX Series II

3000–15000 VA

Harmonic Waveform Generation
Using the latest DSP technology, the iX Series
II controller is capable of generating harmonic
waveforms to test for harmonics susceptibility
of a unit under test. Included is a Graphical User
Interface program that can be used to dene
harmonic waveforms by specifying amplitude and
phase for up to 50 harmonics. The waveform
data points are generated and downloaded by
the GUI to the AC source through either the USB,
IEEE-488, RS232C bus or LAN and remain in
nonvolatile memory. Up to 200 waveforms can
be stored and given a user dened name for easy
recall.

The three phase conguration iX Series II
offers independent waveform generation on
each phase allowing three phase anomalies to
be programmed. It also allows simulation of
unbalanced harmonic line conditions.

Harmonic waveform, Fund., 3rd, 5th, 7th, 9th,11th and 13th.

Two hundred user dened waveforms.

Arbitrary Waveform Generation
[iX Series II only]

Using the provided GUI program or custom
software, the user also has the ability to dene
arbitrary AC waveforms. The arbitrary waveform
method of data entry provides an alternative
method of specifying AC anomalies by providing
specic waveform data points. The GUI program
includes a catalog of custom waveforms. It also
allows real-world waveforms captured on a digital
oscilloscope to be downloaded to one of the
many AC source’s waveform memories.

Arbitrary waveform capability is a exible way of
simulating the effect of real-world AC power line
conditions in both engineering and production
environments.

iX and i Series II -
AC and DC Transient Generation

The iX and i Series II controllers have a powerful
AC and DC transient generation system that
allows complex sequences of voltage, frequency
and waveshapes to be generated. This further
enhances the i/iX’s capability to simulate AC line
conditions or DC disturbances. When combined
with the multi phase arbitrary waveform
capabilities, the AC and DC output possibilities
are truly exceptional. In three phase i/iX system
congurations, transient generation is controlled
independently yet time synchronized on all
three phases. Accurate phase angle control and
synchronized transient list execution provide
unparalleled accuracy in positioning AC output
events.

Transient programming is easily accomplished
from the front panel where clearly laid out menu’s
guide the user through the transient denition
process. The front panel provides a convenient
listing of the programmed transient sequence and
allows for transient execution, Start, Stop, Abort
and Resume operations.

User dened transient sequences can be saved
to nonvolatile memory for instant recall and
execution at a later time. The included Graphical
User Interface program supports transient
denitions using a spreadsheet-like data entry
grid. A library of frequently used transient
programs can be created on disk using this GUI
program.

Transient List Data Entry from the front panel

Two hundred user dened waveforms.

858.458.0223

Transient List Data Entry in GUI program.

[e-mail] 171

i/iX Series II

Measurement and Analysis

The i/iX Series II is much more than a
programmable AC and DC power source. It also
incorporates an advanced digital signal processor
based data acquisition system that continuously
monitors all AC source and load parameters.
This data acquisition system forms the basis for
all measurement and analysis functions. These
functions are accessible from the front panel and
the remote control interface.

Measurement data for single phase (iX Display).

Measurement data for all three phases (iX Display).

Harmonic Analysis [iX Series II only]
The iX Series II provides detailed amplitude and
phase information on up to 50 harmonics of
the fundamental voltage and current for either
one or three phases. Harmonic content can be
displayed in both tabular and graphical formats
on the front panel LCD for immediate feedback
to the operator. Alternatively, the included GUI
program can be used to display, print and save
harmonic measurement data. Total harmonic
distortion of both voltage and current is
calculated from the harmonic data.

Waveform Acquisition [iX Series II only]
The measurement system is based on real-time
digitization of the voltage and current waveforms
using a 4K deep sample buffer. This time domain
information provides detailed information on
both voltage and current waveshapes. Waveform
acquisitions can be triggered at a specic phase
angle or from a transient program to allow
precise positioning of the captured waveform
with respect to the AC source output.

The front panel LCD displays captured waveforms
with cursor readouts. The included GUI program
also allows acquired waveform data to be
displayed, printed and saved to disk.

Acquired Current waveform (iX Display).

Acquired Voltage waveform (iX Display).

Absolute amplitude bar graph display of current harmonics
with cursor positioned at the fundamental (iX Display).

Voltage harmonic measurement table display in absolute
values (iX Display).

www.ProgrammablePower.com172

Acquired three phase voltage waveforms display on PC.

i/iX Series II : Product Specications

3000–15000 VA

Operating Modes

iX Series II AC, DC or AC+DC

i Series II AC or DC

AC Mode Output

Frequency Range: 16.00-1000 Hz (Note: Voltage on 300 V range derates from 300 Vrms max at 500 Hz to 150 Vrms max at 1000 Hz;

Total Power 3001i/iX: 3000 VA, 5001i/iX: 5000 VA, 9003i/iX: 3000 VA per phase, with mode iX: 9000 VA 1ø, 10001i/iX: 10000 VA, 15001i/iX:

Load Power Factor 0 to unity at full output VA

See V-F rating chart. below)

15000 VA, 15003i/iX: 5000 VA/ø 3ø, with mode iX: 15000 VA 1ø

AC Mode Voltage

Voltage Ranges

Output Noise (20 kHz to 1 MHz) < 250 mVrms typ., < 500 mVrms max

Harmonic Distortion (Linear) < 1% from 16 - 66 Hz, < 2% at 400 Hz, < 3% at 800 Hz (Full resistive load)

DC Offset < 20 mV

External Amplitude Modulation Depth: 0 - 10 %, Frequency: DC - 2 KHz

Isolation Voltage 300 Vrms output to chassis

Voltage slew rate 200 µs for 10% to 90% of full scale change into resistive load, 0.5V / µSec

Range V Low V High

AC 0-150 V 0-300 V

AC+DC 0-150 V 0-300 V Line Regulation: < 0.1% for 10% line change

Load Regulation
(with ALC on):

Load Regulation
(with ALC off):

< 0.2%

< 0.5% DC to 100 Hz, < 0.6% 100 Hz to 500 Hz in high voltage range,
< 2.2% 100 Hz to 500 Hz in low voltage range, < 3% 500 Hz to 1000 Hz

AC Mode Current

Steady State AC Current

Peak Repetitive AC Current

Programming Accuracy Voltage (rms): ± 0.2 of range, 16 to 1000 Hz, Frequency: ± 0.01 % of programmed value, Current Limit: ± 0.5 % of programmed value,

Programming Resolution Voltage (rms): 100 mV, Frequency: 0.01 Hz from 16 - 81.91 Hz, 0.1 Hz from 82.0 - 819.1 Hz, 1 Hz from 820-1000 Hz,

Output Relay Push-button controlled or bus controlled output relay

Output Impedance (iX Only) Programmable Z on 3001iX, 5001iX, 9003iX and 15003iX (3ø mode only) for 50 Hz fundamental

Resistive Range: 17 - 1000 mOhm,resolution: 4 mOhm accuracy, 2 % FS

Inductive Range: 230 - 1000 µH, resolution: 4 µH, accuracy: 2 % FS

Model 3001i/iX 5001i/iX

300 V range 11.1 18.5

150 V range 22.2 37.0

Note: Constant power mode provides increased current at reduced voltage (See chart below)

Model 3001i/iX 5001i/iX 9003i/iX 3ø 10001i/iX 15001i/iX 15003i/iX 3ø

High range 96.0 96.0

Low range 110.0 110.0

Phase: < 1.5° with balanced load at 50/60 Hz

Current Limit: 0.1 A, Phase, 0.1°

9003i/iX

11.1 /ø

22.2 /ø

96.0 /

ø

110.0 /ø

10001i/iX 15001i/iX

3ø

37.0 55.5

74.0 111.0

192.0 288.0

220.0 330.0

15003i/iX 3ø

18.5 /ø

37.0 /ø

96.0 /ø

110.0 /ø

DC Mode Output

Power (Max at full scale of
DC Voltage Range):

Voltage Ranges Range: Low: 200 Vdc, High: 400 Vdc

Line Regulation < 0.1% FS or 10% line change

Output Noise < 250 mV rms typ., < 500 mV rms max., (20 kHz to 1 MHz)

Max DC Current (Maximum current
at 65% of V Range)

Current Limit Programmable from 0 A to maximum current for selected range

3001i/iX: 2100 W, 5001i/iX: 3500 W, 9003i/iX: 2100 W/ø 3ø, 6300 W 1ø, 10001i/iX: 7000 W, 15001i/iX: 10500 W,
15003i/iX: 3500 W/ø 3ø

Model 3001i/iX 5001i/iX

400V range 7.8 13 7.8 26 39 13

200V range 15.6 26 15.6 52 78 26

Note: Constant power mode provides increased current at reduced voltage (See chart below)

9003i/iX

10001i/iX 15001i/iX

3ø

15003i/iX 3ø

AC+DC Mode Output

Output Power (iX only) Full AC Power if DC component is less than 20% of full scale voltage, Full DC power if DC component is above 20%

858.458.0223

[e-mail] 173

i/iX Series : Product Specications

Measurements

Output Parameter i Series iX Series

Current Limit Range Programmable 0 to 100% of range for all ranges Programmable 0 to 100% of range for all ranges

Current Limit Resolution 0.1 Arms 0.1 Arms

Current Limit Accuracy ± 0.5 A ± 0.5 A

Frequency Range 16.00 - 81.91 Hz (0.01 Hz resolution)

Frequency Accuracy ± 0.01% of programmed value ± 0.01% of programmed value

DC Offset Voltage Less than 20 mV with linear load. Less than 20 mV with linear load.

Output Impedance Range n/a Rmin to 1000 mΩ

Output Impedance Resolution n/a 4 mΩ

Output Impedance Accuracy n/a ± 2% F.S. at 796 μH and 400 mΩ

Output Noise (20 kHz to 1 MHz) <250 mV rms (typ),

1 Note: AC voltage in 300V range derates from 300 Vrms max. at 500 Hz to 150 Vrms max. at 1000 Hz.

81.0 – 819.1 Hz (0.1 Hz resolution)
820 – 1000 Hz (1 Hz resolution)¹

<500 mV rms (max)

Measurements : Peak AC Current

Output Parameter i Series iX Series

3001i/iX
5001i/iX

10001i/iX 220 A for 150 V range,

15001i/iX 330 A for 150 V range,

Crest Factor Up to 5:1 Up to 5:1

110 A for 150 V range,

92 A for 300 V range

184 A for 300 V range

276 A for 300 V range

16.00 - 81.91 Hz (0.01 Hz resolution)

81.0 – 819.1 Hz (0.1 Hz resolution)
820 – 1000 Hz (1 Hz resolution)¹

Lmin to 1000 μH

4 μH

<250 mV rms (typ),

<500 mV rms (max)

110 A for 150V range,

92 A for 300 V range,

220 A for 150 V range,
184 A for 300 V range

330 A for 150 V range,
276 A for 300 V range

AC Measurements

Parameter Range Accuracy (±) Resolution

Frequency 16.00 - 1000 Hz 2 counts 0.01: 16 to 81.91 Hz

RMS Voltage 0 - 300 Volts 0.25V + 0.1%, <100 Hz

0.25V + 0.2%, 100-1000 Hz

RMS Current 0 - 40 Amps 0.25A + 0.1%, <100 Hz

0.25A + 0.2%, 100-1000 Hz

Peak Current 0 - 119 Amps 0.5A + 0.2%, <100 Hz

0.5A + 0.5%, 100-1000 Hz

VA Power 0 – 6000 VA 10 VA + 0.1%, <100 Hz

20 VA + 0.2%, 100-1000 Hz

Real Power 0 – 6000 W 10 W + 0.1%, <100 Hz

20 W + 0.2%, 100-1000 Hz

Power Factor (>0.2kVA) 0 - 1.00 0.01

Accuracy specications apply above 100 counts. Current and Power Accuracy specications are times two for 10001iX and times three for 15001iX. For 10001iX and 15001iX,
resolution decreases by factor of 10, ranges for current and power increases by factor of three. Measurement bandwidth is limited to 16 Khz.

0.1: 82.0 to 819.0 Hz
1: 820 to 1000 Hz

0.01 Volt

0.001 Amp

0.01 Amp

1 VA

1 W

DC Measurements

Parameter Range Accuracy (±) Resolution

Voltage 0 – 400 Volts 0.4 Volts 0.01 Volt

Current 0 – 40 Amps 0.1 Amps 0.001 Amp

Power 0 – 6000 W 20 W 1 W

Accuracy specications apply above 100 counts. Current and Power Accuracy specications are times two for 10001iX and times three for 15001iX. For 10001iX and 15001iX,
resolution decreases by factor of 10, ranges for current and power increases by factor of three.

www.ProgrammablePower.com174

i/iX Series : Product Specications

3000–15000 VA

Harmonic Measurements (iX series)

Parameter Range Accuracy (±) Resolution

Frequency fundamental 16.00 - 1000 Hz 2 counts 0.01 Hz to 1 Hz

Frequency harmonics 32.00 Hz - 16 kHz 2° typ. 0.5°

Voltage Fundamental 0.25V 0.01V

Harmonic 2 - 50 0.25V + 0.1% + 0.1%/kHz 0.01V

Current Fundamental 0.05A 0.01A

Harmonic 2 - 50 0.05A + 0.1% + 0.1%/kHz 0.01A

Accuracy specications are times three for three phase mode. Harmonics frequency range in three-phase mode is 32 Hz - 16 kHz. Resolution decreases by factor
of 10 for 10001iX and 15001iX.

Remote Control

IEEE-488 Interface optional / USB standard IEEE-488 (GPIB) talker listener. Subset: AH1, C0, DC1, DT1, L3, PP0, RL2, SH1, SR1, T6, IEEE-488.2 SCPI Syntax (GPIB standard on iX)

RS232C Interface

(LAN Optional)

9 pin D-shell connector, Handshake: CTS, RTS, Data bits: 7,8, Stop bits: 1, 2, Baud rate: 9600, 19200, 38400, 57600, 115200, IEEE-488.2
SCPI Syntax (Supplied with RS232C cable). (RS232C Standard on iX - LAN Optional)

AC Input

Voltage 3001 and 9003: 208-240 ± 10% Vac, (L-N, 1ø), All other models: Standard: 208-240 ± 10% Vac, (L-L, 3ø), Option -400: 400-480 ± 10%

Input Line Current (per phase):

Vac, (L-L, 3ø) (Input range must be specied when ordering).

Model 3001i/iX 5001i/iX 9003i/iX 10001i/iX 15001i/iX 15003i/iX

187-264V 25 A 23 A 75 A 46 A 69 A 69 A

360-528V N/A 12 A N/A 24 A 36 A 36 A

Inrush Current per chassis < 100 Apk for 100 µs at 208-240 V, < 50 Apk for 100 µs at 400-480 V

Line Frequency 50-60 Hz ± 10 %

Efciency 75% typical

Power Factor 0.6 typical

Regulatory IEC61010, EN50081-2, EN50082-2, CE EMC and Safety Mark requirements

RFI Suppression CISPR 11, Group1 , Class A

Rear Panel Connectors AC Input & Output terminal block with cover, IEEE-488 (GPIB) connector (rear panel), 9 pin D-Shell RS232C connector*, Remote voltage

sense terminal block, System Interface Connector, *RS232 DB9 to DB9 cable supplied

Mechanical

Dimensions Height: 7” (178 mm), Width: 19” (483 mm), Depth: 24” (610 mm) (depth includes rear panel connectors)

Weight per Chassis: Net: 61 lbs / 28 Kg, Shipping: 115 lbs / 52 Kg

Vibration and Shock Designed to meet NSTA project 1A transportation levels

Air Intake/Exhaust Forced air cooling, side air intake, rear exhaust.

Operating Humidity 0 to 95 % RAH, non condensing.

Temperature Operating: 0 to 40° C, Storage: -20 to +85° C

Constant Power AC Mode - Available Max. AC Current V-F Rating Chart - 300V Range

Note: Specications are subject to change without notice. Specications are warranted over an ambient temperature range of 25°± 5° C. Unless otherwise noted,
specications are per phase for a sinewave with a resistive load and apply after a 30 minute warm-up period. For three phase congurations, all specications are for L-N.
Phase angle specications are valid under balanced load conditions only.

858.458.0223

[e-mail] 175

i/iX Series : Product Specications

Standard controller versions

Model Output Power AC Phase Output Max. current per phase Input Voltage²

Low V range High V range

AC DC AC DC

3001i/iX 3 kVA 1 22 15.6 11 7.8 208-240V

5001i/iX 5 kVA 1 37 26 18.5 13 208-240V

5001i/iX-400 5 kVA 1 37 26 18.5 13 400-480V

9003iX1 9 kVA 3 22 15.6 11 7.8 208-240V

10001i/iX¹ 10 kVA 1 74 52 37 26 208-240V

10001i/iX-400¹ 10 kVA 1 74 52 37 26 400-480V

3

10002i/iX

10002i/iX-400

15001i/iX

15001i/iX-400

15003i/iX

15003i/iX-400

3

1

1

1

1

Note (1): Supplied with System Interface cable(s). Controller in master unit only.
Note (2): All input voltage specications are for Line to Line three phase except 3001iX and 9003iX which require single phase input only.
Note (3): For 10002iX split phase system specications, refer to 5001iX for each phase.

Controller

Controller i iX

AC mode X X

DC mode X X

AC+DC mode X

Transient programming X X

Arbitrary waveforms X

Measurements (standard) X X

Harmonic measurements X

Waveform acquisition X

Programmable Impedance X

IEEE / RS232 / USB X X

Storage

Non Volatile Mem. storage 16 instrument setups, 200 user dened waveforms

Waveforms

Waveform Types i Series II: Sine, iX Series II: Sine, Square, Clipped sine, User dened

User dened waveform storage Four groups of 50 user dened arbitrary waveforms of 1024 points for a total of 200 (One group can be active at a time)

System Interface

Inputs Remote shutdown, External Sync, Clock/Lock (option)

Outputs Function Strobe, Clock/Lock (option)

Protection

Over Load Constant Current or Constant Voltage mode

Over Temperature Automatic shutdown

10 kVA 2 37 26 18.5 13 208-240V

10 kVA 2 37 26 18.5 13 400-480V

15 kVA 1 111 78 55.5 39 208-240V

15 kVA 1 111 78 55.5 39 400-480V

15 kVA 3 37 26 18.5 13 208-240V

15 kVA 3 37 26 18.5 13 400-480V

www.ProgrammablePower.com176

i/iX Series Diagram

19.00

[48.26]

1.48

[3.76]

4.00

[10.16]

6.97

[17.70]

22.56

[57.30]

1.63

[4.14]

.19

[.48]

(OPTIONAL)

GENERAL DEVICES

RACK SLIDE

C300S-120-B308

1.18

[3.00]

16.80

[42.67]

3000–15000 VA

© 2009 AMETEK Programmable Power All rights reserved. AMETEK Programmable Power is the trademark of AMETEK Inc., registered in the U.S. and other countries.
Elgar, Sorensen, California Instruments, and Power Ten are trademarks of AMETEK Inc., registered in the U.S.

858.458.0223

[e-mail] 177

i/iX Series

Supplied with

User Manual, Programming Manual, Software (all on CD ROM) and RS232C serial cable.

Options

Option Code Description

-160 RTCA/DO-160D and EUROCAE test rmware. Refer to -160 option data sheet for details.

-400 400-480 Volt Line to Line AC input.

-411 IEC61000-4-11 test rmware. See also EOS1/3.

-413 IEC61000-4-13 Harmonics and Interharmonics test rmware and hardware.

-704 Mil Std 704D/E test rmware. Refer to -704 option data sheet for details. 704F Software

-EOS-1 IEC61000-4-11 Electronic Output Switch (1 phase) Includes -411 option. Refer to EOS data sheet for details.

-EOS-3 IEC61000-4-11 Electronic Output Switch (3 phase) Includes -411 option. Refer to EOS data sheet for details.

-LKM Clock/Lock Master

-LKS Clock/Lock Auxiliary

-LNS Internal AC Line Sync.

-XLS External AC Line Sync adaptor. (-LNS and XLS are mutually exclusive)

-MODE-iX Switches between 1 and 3 phase output modes, for 9003iX or 15003i/iX only. (Separate box)

OMNI-1-18i Impedance matching network for single phase 3001i/iX or 5001i/iX to support IEC-1000-3-3 icker tests.

OMNI-3-18i Impedance matching network for three phase 9003iX or 15003i/iX systems to support IEC-1000-3-3 icker tests.

OMNI-3-37i Impedance matching network for three phase 30003i/iX systems to support IEC-1000-3-3 icker tests.

-RMS Rackmount Slides.

-WHM Watt-Hour Measurement option.

-ABD Airbus Directive 0100.1.8 tests.

-AMD Airbus AMD24 tests.

-A350 Airbus A350 tests.

-AIRB Airbus test package (A380, A350, AMD24)

-B787 Boeing 787B3-0147 tests.

Cabinets Multi box iX Series II systems can be factory installed and wired in 19 inch cabinets. Cabinet congurations can be ordered by

preceeding the model number with a “C1-C4” prex. Contact factory for pricing and details.

www.ProgrammablePower.com178