Atec IFI-T2618 User Manual

T2618
Series Medium to High Power Millimeter TWT Amplifiers
18.0 – 26.5 GHz • 10-200 watts, Minimum Rated Power
Specifications subject to change without notice Page 1 ds-t2618-series rev-a-3/18/2011
Operation safety and ease of use are paramount in IFI product designs. The IFI T2618 Series include a full complement of RF and hardware protection systems including high VSWR, over-current and voltage protection as well as redundant thermal and airflow sensors to prevent the TWT from overheating. In addition, the T2618 series includes a state-of-the-art interface that is sophisticated, comprehensive, but yet simple to use. Our amplifiers feature modular construction and this concept of modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities.
The backlit LCD screen shows forward/reverse power indication, system status and self-diagnostic information. All the amplifier operating parameters are simultaneously available in the amplifier front panel display as well as over the remote bus. Selection switches allow you to switch the amplifier to the desired mode of operation for local control if the unit is not being operated remotely.
For computer automation both an RS-232 and IEEE-488 interface are included. To meet individual application needs, the T2618 Series amplifiers can be easily customized with harmonic filters or other options. With this capability and its reliable elegant design, the T2618 series amplifiers are the perfect amplifier for your microwave needs. IFI offers different size packages and configurations to best suit your application. A product and design built to last!
IFI RF Power Amplifier Features:
Instantaneous Broadband Frequency range
Modular Design Construction
Rugged Construction & High Reliability
Backlit LCD Display
Integrated Force Air Cooling
Self-diagnostic circuitry
IEEE-488 interface, RS232 & Ethernet Remote available
Solid State Power Supply
Models & General Specifications:
Model
Number
Frequency
Range (GHz)
Rated Power
(watts minimum)
P1dB Power
(nominal)
Gain
(dB min)
Mains (kVA)
Weight
(Pounds)
Size
(Inches)
T2618-10
18.0-26.5
10
8
40
0.7
45
5.25”H x 19”W x 24.00”D
T2618-25
18.0-26.5
25
10
44
0.8
45
5.25”H x 19”W x 24.00”D
T2618-40
18.0-26.5
40
20
46
0.9
45
5.25”H x 19”W x 24.00”D
T2618-50
18.0-26.5
50
25
47
1.0
45
5.25”H x 19”W x 24.00”D
T2618-80
18.0-26.5
80
35
49
1.8
80
14.0”H x 19”W x 25.25”D
T2618-100
18.0-26.5
100
45
50
1.9
90
14.0”H x 19”W x 25.25”D
T2618-125
18.0-26.5
125
50
52
2.0
100
14.0”H x 19”W x 25.25”D
T2618-200
18.0-26.5
200
100
53
3.5
200
2x 14.0”H x 19”W x 27.00”D
Standard Features for IFI T2618 Series TWT Amplifiers
VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open & Short Circuit Protection.
* Alternate Prime Power (specify at time of order) GPIB IEEE 488 & RS232 Remote Control RF Sample Port on the Front Panel, 112R for rear panel Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
Standard Features
RF Input/Output Connectors on the Front Panel, 118R for rear panel
T2618
Series Medium to High Power Millimeter TWT Amplifiers
18.0 – 26.5 GHz • 10-200 watts, Minimum Rated Power
Specifications subject to change without notice Page 2 ds-t2618-series rev-a-3/18/2011
Internal Systems Diagnostics & Status Indicators Filament/Beam Elapsed Time Metering in hours RF Safety Interlock Forward/Reflected Power Indication simultaneously on Front Panel display
Specifications:
Frequency Range:
As Specified in Model Table
Rated Output Power:
As Specified in Model Table
Gain @ Rated Power:
As Specified in Model Table
Prime Power:
As Required for Customer (Some are listed below)
Input/output Impedance:
50 ohms
RF Input/ Sample Connectors:
Type K Female, unless specified otherwise
RF Output Connector:
WR42
Other waveguides available by request or specification (see Option 117)
Input VSWR:
2.0:1
Output VSWR:
2.5:1
Operating Temp:
0º to 50º C
Non-operating Temp/Altitude:
-40º to 70º C (50,000 feet max)
Humidity:
95% without condensation
Operating Altitude:
10,000 feet
Cooling System:
Air cooled, self-contained
Modulation:
All types, AM, FM, Pulse
Configuration:
Rack Mount as specified in Model Table, or Cabinet Integrated as needed
Spurious Outputs:
<-60 dBc nominal
Standard Prime Powers:
100, 115, 120 VAC ±10% 50/60 Hz, single phase 200, 220, 230, 240VAC ±10% 50/60 Hz, single phase 100/200VAC,115/208 or 200/220/230/240VAC ±10% 50/60 Hz, three phase Wye or Delta and/or 400 Hz power is available.
Special Prime Powers other then listed are subject to availability
Some Available Options for IFI T2618 Series TWT Amplifiers
Option 103 G/D:
VSWR Reflected Power Protection “Graceful Degradation Feature” which will automatically reduce the input drive and fold back the output power when the average reflected power exceeds a preset limit of 3.0:1. The unit operates without damage or oscillation into any magnitude of phase or load impedance.
Option 110-1E:
GPIB IEEE-488 RS232 and Ethernet Remote Control
Option 110-2:
GPIB IEEE-488 and RS 422 Remote Control
Option 110-3
GPIB IEEE-488 and RS 485 Remote Control
Option 113:
Chassis Slides for 19” Rack Mounting
Option 118F or R:
Front Panel RF Connections 118R for Rear Panel RF Connections
Option 123F or R:
Reflected RF Sample Port -40, -50 or -60dB N or SMA, Front or Rear Panel
Loading...
+ 1 hidden pages