Atec IFI-SCCX User Manual
SCCX Solid State RF Power Amplifiers
10 KHz – 220 MHz • 10 to 1200 watts, Minimum Rated Power
Page 1 ds-sccx series rev-a-1/3/2011
Instruments for Industry, SCCX-Series Amplifiers provide outstanding RF performance. These products are available
in a wide range of power levels from 10 watts to 1200 watts in the 10KHz - 220MHz frequency range.
These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.
IFI RF amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term
reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies
up to 220MHz.
Our RF power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a
shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service
and rapid turnaround at depot level repair facilities.
From the ground up, the “SCCX-SERIES” products are structurally engineered to withstand operation in mechanically
hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh
environments.
Features
• Solid State Design
• Rugged Construction & High Reliability
• Instantaneous Broadband Frequency range
• Backlit screen
• Modular Design Construction
• Integrated Force Air Cooling
• Self-diagnostic circuitry
• IEEE-488 interface & RS232 Remote
Models & General Specifications!
Model
Number!
Frequency
Range (MHz)!
Rated Power
(Watts) Minimum!
P1dB Power
Watts Minimum!
Gain (dB)
Minimum!
KVA
Weight
In Pounds
Size
In Inches
SCCX10
10KHz – 220MHz
10
10
40
.1KVA
33 Lbs
5.25” H x 19” W x 24” D
SCCX25
10KHz – 220MHz
25
25
44
.2KVA
35 Lbs
5.25” H x 19” W x 24” D
SCCX50
10KHz – 220MHz
50
50
47
.4KVA
36 Lbs
5.25” H x 19” W x 24” D
SCCX100
10KHz – 220MHz
100
80
50
.5KVA
38 Lbs
5.25” H x 19” W x 24” D
SCCX150
10KHz – 220MHz
150
100
52
.8KVA
40 Lbs
5.25” H x 19” W x 24” D
SCCX200
10KHz – 220MHz
200
160
53
1.5KVA
80 Lbs
14.0” H x 19” W x 27” D
SCCX250
10KHz –220MHz
250
200
54
2.0KVA
90 Lbs
14.0” H x 19” W x 27” D
SCCX350
10KHz – 220MHz
350
280
56
2.5KVA
95 Lbs
14.0” H x 19” W x 27” D
SCCX500
10KHz – 220MHz
500
300
57
3.0KVA
100 Lbs
14.0” H x 19” W x 27” D
SCCX800
10KHz – 220MHz
800
500
60
5.0KVA
400 Lbs
Rack Integrated
SCCX1200
10KHz – 220MHz
1200
800
62
10.0KVA
650 Lbs
Rack Integrated
SCCX Solid State RF Power Amplifiers
10 KHz – 220 MHz • 10 to 1200 watts, Minimum Rated Power
Page 2 ds-sccx series rev-a-1/3/2011
Standard Features for IFI SCCX-Series Solid State Amplifiers
VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance,
Open & Short Circuit Protection.
* Alternate Prime Power (specify at time of order)
GPIB IEEE 488 & RS232 Remote Control
RF Sample Port on the Front Panel, 112R for rear panel
Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
Gain Control Local & Remote, 30dB range
RF Input/Output Connectors on the Front Panel, 118R for rear panel
Internal Systems Diagnostics & Status Indicators
Total/Operate Elapsed Time Metering in hours
RF Safety Interlock
Standard
Features:
Forward/Reflected Power Indication simultaneously on Front Panel display
IFI SCCX-Series Solid State Amplifier Specifications
Frequency Range:
As Specified in Model Table
Rated Output Power:
As Specified in Model Table
Gain @ Rated Power:
As Specified in Model Table
Prime Power:
As Required (Some are listed below)
Input/output Impedance:
50 ohms
RF Input/ Sample Connectors:
Type N Female, unless specified otherwise
RF Output Connector:
Type N Female
Other connectors available by request or specification
Input VSWR:
2.0:1
Output VSWR:
2.5:1
Operating Temp:
0º to 50º C
Non-operating Temp:
-40º to 70º C (50,000 feet max)
Humidity:
95% without condensation
Altitude:
10,000 feet
Cooling System:
Air cooled, self-contained
Modulation:
AM,FM, Pulse
Configuration:
Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
Spurious Outputs:
<-60 dBc nominal
Harmonics:
-20dBc minimum @ Linear Power
Standard Prime Powers:
100, 115, 120 VAC ±10% 50/60 Hz, single phase
220, 230, 240VAC ±10% 50/60 Hz, single phase
100/110/1115/120 ±10% 50/60 Hz, three phase Wye or Delta power is available
200/220/230/240VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
Special Prime Powers other then listed are subject to availability
Some Available Options for IFI SCCX-Series Solid State Amplifiers
Option 110-1E:
GPIB IEEE-488 RS232 and Ethernet Remote Control
Option 110-2:
GPIB IEEE-488 and RS 422 Remote Control
Option 110-3
GPIB IEEE-488 and RS 485 Remote Control
Option 113:
Chassis slides for a 19" rack mounting
Option 118A:
RF Input On Front Output On Rear
Option 118B:
RF Input On Rear Output On Front
Loading...