Page 1
ECAT
Model E411
®
EFT/Noise
Burst Simulator for
IEC 1000-4-4 to 4.4 kV
FEATURES
™
• All test parameters under full software control via
KeyTek BurstWare
Polarity Burst Voltage 0-360° Line Sync
Frequency Burst Duration Coupling Modes
Period Test Duration
• Burst Voltages from 200V to 4.4kV
• IEC specified 5ns/50ns impulses into 50 ohms- also
meets the proposed 5/100ns requirement into a high
impedance.
™
:
A plug-in module for ECAT
systems for testing in accordance
with IEC 1000-4-4 (IEC 801-4).
• 50 ohm source impedance
• Built-in pulse monitor, attenuated to 1kV/V
for convenient monitoring without the need for
high voltage probes.
• Real World EFT options including Chirp and
frequencies to 2MHz.
SYSTEM BENEFITS
• The ECAT is configurable as a compact,
standalone system with one test capability or as
an integrated, multiple capability tester.
• Unparalleled safety features for high voltage
testing, including a complete interlock system that
not only disables simulator operation if activated, but
completely removes AC mains power from the EUT,
when using any KeyTek AC mains coupler/decoupler.
• Automatic report generation using KeyTek’s
exclusive Windows
• Modular system construction provides the ability to
upgrade test capabilities as requirements change or
evolve.
• Single port testing for Surge, EFT and PQF
coupled disturbances allows changing test modes
without switching off power to the EUT. This avoids
lost time due to re-initializing the EUT between tests.
®
-based software.
™
mains
Page 2
Model E411
SPECIFICA TIONS AND TOLERANCES
ELECTRICAL (PER IEC 1000-4-4)
Burst Polarity: Positive, negative, alternating
Burst Voltage: 200V to 4.4kV
Burst Voltage
Resolution: 5V
Burst Voltage ±10% of setting ÷ 2 with
Tolerance: 50Ω load, ±20% of setting
with no load
Burst Frequency: Adjustable from 1kHz to 1MHz
up to 4.4kV
Burst Duration: 1.0ms to 20ms; 1.0ms
resolution or 1 to 200 pulses
Period Between Adjustable from 300ms to 5s;
Bursts: 1ms resolution
Burst Test Length: 1 to 360 sec.; 1 sec. resolution
1 to 240 min.; 1 min. resolution
1 to 24 hours; 1 hour resolution
W ait Time 1 to 360 sec.; 1 sec. resolution
Between Tests: 1 to 240 min.; 1 min. resolution
1 to 24 hours; 1 hour resolution
Voltage Monitor: Built-in; 150MHz bandwidth
Note: For any combination of
frequency, duration and period,
the number of pulses cannot
exceed 600 per second and
200 per burst.
PHYSICAL
Height: 21cm (81/4”)
Width: 21cm (8
Depth: 52cm (20
1
/4”)
3
/8”)
Weight: 11.4kg (25 lbs.)
MINIMUM SYSTEM REQUIREMENTS
E100 series control center and
E000 blank plug-in module (If no other half-width
module is ordered)
AVAILABLE OPTIONS
E411-CH Chirp capability – provides an output in
which the amplitude increases and the
frequency decreases during the burst,
similar to actual EFT events.
E411-2MHz: Hardware option to provide burst
frequency operation to 2MHz,
at voltages to 3kV.
CCL-4: A covered, safety-interlocked capacitor
clamp for coupling the burst to I/O lines
(including data and signal lines). All
clamp surfaces are nickel-plated and
the hinges are nickel-plated, beryllium
copper finger-stock to insure excellent
RF performance over time.
CCL-4/S: A covered, safety-interlocked capacitor
clamp for coupling the EFT/Noise
burst into I/O lines (including data
and signal lines).
™
ECAT: AN EXTRAORDINARY CONCEPT IN EMC
TESTING FOR VULNERABILITY TO SURGE,
EFT AND POWER QUALITY.
ECAT is a totally integrated and modularized system
which offers unprecedented testing ease, accuracy and
versatility to manufacturers, test houses, and anyone
who will be testing for effects of Pulsed EMI.
ECAT is designed to test products according to a broad
range of international standards developed by ANSI,
the IEC, CENELEC and other agencies. The European
Norms, developed by CENELEC, became mandatory
on January 1, 1996 for all equipment shipped into the
European Union or shipped across EU borders.
For additional ECAT®product literature call, email or
fax the KeyTek sales department.
One Lowell Research Center
Lowell, Massachusetts 01852-4345 USA
1 800 753 9835 • Tel: 1 978 275 0800 • Fax: 1 978 275 0850
email: sales@keytek.com
http://www.keytek.com
A division of Thermo Voltek, a Thermo Electron company
KeyTek and ECAT are registered trademarks and BurstWare, EFT/Noise, and PQF are
trademarks of Thermo Voltek Corporation. ©Thermo Voltek. Specifications are subject
to change without notice. Printed in USA.
KPS-510B-11/97
Loading...