Atec AR-CI00401A User Manual
Model CI00401A, M1, M2
RF Conducted Immunity System
150 Watts
Complete Testing Solutions to the following standards:
ISO 11452-4
GMW 3097
ES-XW7T-1A278-AC
DC-11224
BMW GS95002
Peugeot B217110
Renault 36-00-8081-G
IEC 61000-4-6
Other automotive standards
The Model CI00401A is a fully self-contained state of the art system
designed to test RF Conducted Immunity. The CI00401A contains all the
instruments needed to perform conducted immunity testing for automotive
and IEC specifications. The system contains a signal generator, three channels of power monitoring, 150W AR amplifier
100 kHz to 400 MHz, directional coupler, and emcware® control software. Everything is contained in a single housing,
which eliminates setup issues. This system provides the versatility needed for every test laboratory and equipment
manufacturer. The RF amplifier and the signal generator can be used independently of the system. If special needs arise
or standards were to change, a larger amplifier can be connected to the system. The use of spectrum analyzers and
monitoring equipment may also be controlled by the software.
The export classification for this equipment is EAR99. These commodities, technology or software are controlled for export
in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
Internal Test Specifications (See Note 1)
ISO 11452-4
GMW 3097
ES-XW7T-1A278-AC
DC-11224
BMW GS95002
Peugeot B217110
Renault 36-00-8081-G
IEC-61000-4-6
Other automotive standards
Signal Generator Specifications
Frequency range
resolution
Power range
resolution
Modulation AM, FSK. FM, Phase, External Pulse
NOTE 1: Specifications can be met using AR-specified external accessories (injection probes, monitor probes, cal fixtures, CDN’s,
attenuators, etc.) Contact AR for further information.
NOTE 2: The use of a spectrum analyzer may be necessary on some of the low level bulk current injection tests. This is especially true on
power and I/O lines with a great amount of ambient noise.
9 kHz to 1.2 GHz
1Hz
-140 to +13 dBm
0.1 dB
Power Meter Specifications (See Note 2)
Power heads 3
Type Diode
Frequency 10 kHz to 8 GHz
Range -60 to +20 dBm
RF Amplifier Specifications
Frequency range 100 kHz to 400 MHz
Power rating 150 Watts Minimum
1dB compression 120 Watts Minimum
Harmonic Distortion -20 dBc at 120 Watts
Mismatch tolerance 100% of rated power without
fold back. Will operate without
damage or oscillation with any
magnitude of source and load
impedance.
Gain 52 dB minimum
100 kHz–400 MHz
Approved for public release by AR RF/Microwave Instrumentation 092412
160 School House Road Souderton, PA 18964-9990 • 215-723-8181 • www.arworld.us Page 1 of 2
Connections
RF Out Type N (front)
Monitor Port In Type N (front)
Signal Generator Out Type N (rear)
Directional Coupler In Type N (rear)
Amplifier Out/In Type N (rear)
Pulse In BNC (rear)
Communication GPIB (IEEE 488) (rear)
Directional Coupler Fwd Out Type SMA (rear)
Directional Coupler Fwd In Type SMA (rear)
Directional Coupler Rev Out Type SMA (rear)
Directional Coupler Rev In Type SMA (rear)
Monitor Port Out Type SMA (rear)
Monitor Port In Type SMA (rear)
Power Meter Calibration Port Out Type SMA (rear)
MODEL CONFIGURATIONS
MODEL DESCRIPTION
CI00401AM1 Includes Option 2
CI00401AM2 Includes Options 1 and 2
Application Model Description
IEC 61000-4-6* TK1000 Conducted immunity test kit containing all the attenuators, injection
probes, calibration fixtures, calibration resistors, and termination
resistors necessary for IEC testing.
Automotive TK3000 Conducted immunity test kit containing all the attenuators, injection
probes, calibration fixtures, calibration resistors, and termination
resistors necessary for automotive testing.
*Requires additional AF10050, 10 dB, 50-watt attenuator.
General
Power 115/230 VAC
50/60 Hz, single phase 16A
Breaker 2 pole, 20A
Cooling active cooling, air ventilation
Environmental conditions 10°C - 40°C
Dimensions, 50.3 x 42.2 x 52.1 cm
19.8 x 16.6 x 21.7 in
Weight 22.7 kg (50.0 lb)
Control Software
emcware® Software Suite
PC Requirements
Computer 2 GHz Single Core Processor
Operating system Windows, XP, Windows Vista,
Windows 7
RAM 1 GB Minimum
Screen Resolution 1024 x 768
Ports 2 available USB 2.0 ports
Options
1 External USB data acquisition card.
2 Laptop PC with software preinstalled
ACCCESSORY KITS
Page 2 of 2
Loading...