Atec AR-CI00400A User Manual

Model CI00400A,

M1 through M7

RF Conducted Immunity System

100 Watts nominal

Complete testing solutions to the following standards:

 MIL-STD-461D & E CS114  DO160D & E BCI Testing  EN/IEC 61000-4-6  IEC 60601-1-2  EN 50130-4  EN 61000-6-1/2  EN 55024

The Model CI00400A is a fully self-contained state of the art system designed to test RF Conducted Immunity. The system contains a signal

generator, 3 channel power meter, 100W nominal AR amplifier 10kHz to 400MHz, directional coupler, and emcware® control software. Everything is contained in a single housing, which eliminates setup issues. This system provides the versatility needed for every test laboratory and equipment manufacturer. The RF amplifier and the signal generator can be used independently of the system. If special needs arise or standards were to change a larger amplifier can be connected to the system. The use of spectrum analyzers and monitoring equipment may also be controlled by the software.

Option 1 adds an additional power head for testing automotive standards such as Ford, GM, Chrysler, BMW, Renault, and ISO11452-4. Option 2 adds data acquisition capability. Option 3 provides a laptop PC preloaded with the test software. Option 4 is a lower cost solution providing all the functions and features of the full CI00400A base model without the cost of the internal amplifier.

The export classification for this equipment is EAR99. These commodities, technology or software are controlled for export in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.

Internal Test Specifications (See NOTE 1)

CI00400A CI00400A w/Option 1 MIL-STD-461D (CS114) MIL-STD-461E (CS114) ISO 11452-4 DO160D (Sec 20 BCI Test) GMW 3097 DO160E (Sec 20 BCI Test) Ford ES-XW7T-1A278-AC IEC/EN 60601-1-2 DaimlerChrysler DC-11224 IEC/EN 50130-4 BMW GS95002 IEC/EN 61326 Renault 36-00-8081-G IEC/EN 61000-6-1 IEC/EN 61000-6-2 IEC/EN 61000-4-6 CISPR 24/EN 55024

NOTE 1: Specifications can be met using AR-specified external accessories (injection probes, monitor probes, cal fixtures, CDN’s,

attenuators, etc.) Contact AR for further information.

NOTE 2: The use of a spectrum analyzer may be necessary on some of the low level bulk current injection tests. This is especially true on

power and I/O lines with a great amount of ambient noise.

All standards of CI00400A plus:

Signal Generator Specifications Frequency range resolution Power range resolution Modulation AM, FSK. FM, Phase, External

Power Meter Specifications (See NOTE 2) Channels 3 Power heads 2 Type diode Frequency 10kHz to 8GHz Range -60 to +20 dBm

9 kHz to 1.2 GHz 1Hz

-140 to +13 dBm

0.1dB

Pulse

10 kHz–400 MHz

Approved for public release by AR RF/Microwave Instrumentation 092412

160 School House Road Souderton, PA 18964-9990 • 215-723-8181 • www.arworld.us Page 1 of 2

RF Amplifier Specifications Frequency range 10 kHz to 400 MHz Power rating 100 Watts Nominal 1dB compression 75 Watts Nominal Harmonic Distortion -20dBc at 50 Watts Mismatch tolerance 100% of rated power without

fold back. Will operate without damage or oscillation with any magnitude of source and load impedance.

Gain 51dB minimum

Connections RF Out Type N (front) Monitor Port In Type N (front) Signal Generator Out Type N (rear) Directional Coupler In Type N (rear) Amplifier Out/In Type N (rear) Pulse In BNC (rear) Communication GPIB (IEEE 488) (rear) Directional Coupler Fwd Out Type SMA (rear) Directional Coupler Fwd In Type SMA (rear) Directional Coupler Rev Out (with Option 1) Directional Coupler Rev In (with Option 1) Monitor Port Out Type SMA (rear) Monitor Port In Type SMA (rear) Power Meter Calibration Port Out Type SMA (rear)

Application Model Description

IEC 61000-4-6

BCI Clamp

50 System

IEC 61000-4-6

BCI Clamp

150 System

IEC 61000-4-6

EM Clamp

50 System

MIL-STD-461

DO160

Automotive TK3000 Conducted immunity test kit containing all the attenuators, injection

Type SMA (rear)

TK1000 Conducted immunity test kit containing all the attenuators, injection

probes, calibration fixtures, calibration resistors, and termination resistors necessary for IEC testing.

TK1001 Conducted immunity test kit containing all the attenuators, injection

probes, calibration fixtures, calibration resistors, and termination resistors necessary for IEC testing.

TK1002 Conducted immunity test kit containing all the attenuators, injection

probes, calibration fixtures, calibration resistors, and termination resistors necessary for IEC testing.

TK2000 Conducted immunity test kit containing all the attenuators, injection

probes, calibration fixtures, calibration resistors, and termination resistors necessary for MIL-STD-461 and DO160 testing.

probes, calibration fixtures, calibration resistors, and termination resistors necessary for automotive testing.

General

Power 115/230 VAC

50/60 Hz, single phase 16A Breaker 2 pole, 20A Cooling active cooling, air ventilation Environmental conditions 10°C - 40°C Dimensions, 50.3 x 42.2 x 52.1 cm

19.8 x 16.6 x 21.7 in Weight 22.7 kg (50.0 lb) Weight CI00400AM5 17.3 kg (38.2 lb)

Control Software

emcware® Software Suite

PC Requirements Computer 2GHz Single Core Processor Operating system Windows XP, Windows Vista,

Windows 7 RAM 1 GB Minimum Screen Resolution 1024 x 768 Ports 2 available USB 2.0 ports

Options

1 Additional power head to add the ability to monitor

reverse power 2 Data acquisition card. 3 Laptop PC with software preinstalled 4 Amplifier removed; requires use of external amplifier

MODEL CONFIGURATIONS

MODEL DESCRIPTION

CI00400AM1 Includes Option 3

CI00400AM2 Includes Options 2 and 3

CI00400AM3 Includes Option 2

CI00400AM4 Includes Option 1

CI00400AM5 Includes Option 4

CI00400AM6 Includes Options 1 and 4

CI00400AM7 Includes Options 1 and 3

ACCCESSORY KITS

Page 2 of 2