Atec AR-CI00250A User Manual

Model CI00250A,

Internal Test Specifications*

IEC/EN 60601-1-2

CISPR 24/EN 55024

IEC 61000-4-6 procedure and

Signal Generator Specifications

SG1200

SG6000 (optional)

Frequency range

9 kHz to 1.2 GHz

100kHz to 6 GHz

Power range
resolution

-140 to +13 dBm

0.1dB

-110 to +7 dBm

0.02 dB

Modulation

AM, FSK. FM, Phase,

AM, FM, Phase,

Pulse

Power Meter Specifications

Channels

3

Power heads

1

Type

diode

Frequency

10kHz to 8GHz

Range

-60 to +20 dBm RF Amplifier Specifications

Frequency range

10 kHz to 250 MHz

Power rating

75Watts Minimum

1dB compression

50 Watts Minimum

Harmonic Distortion

-20dBc at 50 Watts

Mismatch tolerance

100% of rated power without

impedance.

Gain

49dB minimum

M1 through M12

RF Conducted Immunity System

75 Watts

10 kHz–250 MHz

Complete Testing Solutions to the following standards:

• EN/IEC 61000-4-6

• IEC 60601-1-2

• EN 50130-4

• EN 61000-6-1/2

• EN 55024

• CISPR 14-2

The Model CI00250A is a fully self-contained state of the art system
designed to test RF Conducted Immunity. The CI00250A contains all the

instruments needed to perform conducted immunity testing to the IEC
61000-4-6 specification. The system contains a signal generator, 3 channel power meter, 75W minimum AR amplifier
10kHz to 250MHz, and emcware® control software. Everything is contained in a single housing, which eliminates setup
issues. This system will have the versatility needed for every test laboratory and equipment manufacturer. The RF amplifier
and the signal generator can be used independently of the system. If special needs arise or standards were to change a
larger amplifier can be connected to the system. The use of spectrum analyzers and monitoring equipment may also be
controlled by the software.

The export classification for this equipment is EAR99. These commodities, technology or software are controlled for export
in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.

IEC/EN 50130-4

IEC/EN 61326
IEC/EN 61000-6-1
IEC/EN 61000-6-2

*Specifications can be met using AR-specified external
accessories (injection probes, monitor probes, cal fixtures,
CDN’s, attenuators, etc.) Contact AR for further information.

resolution

1Hz

External Pulse

levels

Approved for public release by AR RF/Microwave Instrumentation 111412

160 School House Road Souderton, PA 18964-9990 • 215-723-8181 • www.arworld.us Page 1 of 2

0.01 Hz

Internal/External

fold back. Will operate without

damage or oscillation with any
magnitude of source and load

General

Power

115/230 VAC
50/60 Hz, single phase 16A

Breaker

2 pole, 20A

Cooling

active cooling, air ventilation

Environmental conditions

10°C - 40°C

Dimensions,

50.3 x 42.2 x 52.1 cm

Weight

20.5 kg (45.0 lb)

Control Interface

GPIB Adaptor

USB to GPIB adaptor included
(NI-GPIB-USB-HS)

Connections

RF Out

Type N Male (front)

Monitor Port In

Type N Male (front)

Signal Generator Out

Type N Male (rear)

Amplifier In

Type N Male (rear)

Pulse In

BNC Male (rear)

Communication

GPIB (IEEE 488) (rear)

Directional Coupler Fwd Out
(with Option 1)

Type SMA (rear)

Directional Coupler Fwd In
(with Option 1)

Type SMA (rear)

Directional Coupler Rev Out
(with Option 2)

Type SMA (rear)

Directional Coupler Rev In
(with Option 2)

Type SMA (rear)
Monitor Port Out

Type SMA (rear)

Monitor Port In

Type SMA (rear)

Power Meter Calibration Port Out

Type SMA (rear)

Control Software

emcware® Software Suite

PC Requirements

Computer

2 GHz Single Core Processor

Operating system

Windows, XP, Windows Vista,

Windows 7

RAM

1 GB Minimum

Screen Resolution

1024 x 768

Ports

2 available USB 2.0 ports Options

1

Directional coupler and additional power head to level

2

Additional power head to add the ability to monitor
reverse power

3

Data acquisition card

4

Laptop PC with software preinstalled

5

100 kHz to 6 GHz Signal Generator SG6000
(Replaces standard Signal Generator SG1200)

6

ISO 17025-accredited calibration for system

7

Amplifier removed; requires use of external amplifier.

MODEL CONFIGURATIONS

MODEL

DESCRIPTION

CI00250AM1

Includes Option 4

CI00250AM2

Includes Option 1

CI00250AM3

Includes Options 1 and 4

CI00250AM4

Includes Options 1 and 3

CI00250AM5

Includes Option 5

CI00250AM6

Includes Options 3 and 5

CI00250AM7

Includes Option 6

CI00250AM8

Includes Options 3 and 6

CI00250AM9

Includes Options 3 and 4

CI00250AM10

Includes Options 1, 3 and 4

CI00250AM11

Includes Option 7

CI00250AM12

Includes Options 4 and 6

Accessory Kits

Application

Model

Description

IEC 61000-4-6

50Ω System

TK1000

Conducted immunity test kit containing all the attenuators, injection

resistors necessary for IEC testing.

IEC 61000-4-6

150Ω System

TK1001

Conducted immunity test kit containing all the attenuators, injection

resistors necessary for IEC testing.

IEC 61000-4-6

50Ω System

TK1002

Conducted immunity test kit containing all the attenuators, injection

resistors necessary for IEC testing.

19.8 x 16.6 x 21.7 in

on and monitor forward power

BCI Clamp

BCI Clamp

EM Clamp

probes, calibration fixtures, calibration resistors, and termination

probes, calibration fixtures, calibration resistors, and termination

probes, calibration fixtures, calibration resistors, and termination

Page 2 of 2