Atec AR-60S1G3 User Manual

A
r
h
r
t
b
r
a
160 School House Road, Souderton, PA 18964-9990 US
Phone 215-723-8181•FAX 215-723-5688
The Model 60S1G3 is a solid state, self-contained, air-cooled, broadband amplifier designed fo applications where instantaneous bandwidth, high gain and linearity are required. Housed in a stylis contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet fo immediate equipment rack mounting.
The 60S1G3, when used with a sweep generator, will provide a minimum of 60 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired outpu level. The 60S1G3 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature
y removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions if an over-temperature or powe supply fault has occurred. The unit can be returned to operate when the condition has been cleared. The 60S1G3 digital panel provides control of all amplifier functions both locally and remotely vi IEEE-488 (GPIB) or RS-232 interfaces.
The low level of spurious signals and linearity of the Model 60S1G3 make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.
60S1G3
Typical Performance
140 130 120 110 100
90 80 70 60 50 40 30
OUTPUT POWER (Watts)
20 10
0
0.5 1 1.5 2 2.5 3 3.5
3RD ORDER INTERCEPT POINT
LINEAR @ 3dB COMPRESSION
LINEAR @ 1dB COMPRESSION
FREQUENCY (GHz)
MODEL 60S1G3 M1, M2, M3, M4, M5 60 WATTS CW
-
70
60
50
40
30
20
10
3RD ORDER INTERCEPT POINT (dBm)
0
REV051704
Model 60S1G3
RATED POWER OUTPUT................ 60 watts minimum
INPUT FOR RATED OUTPUT................... 1.0 milliwatt
.......................................................................... maximum
POWER OUTPUT @ 3dB COMPRESSSION
Nominal............................................................ 70 watts
Minimum.......................................................... 60 watts
POWER OUTPUT @ 1dB COMPRESSION
Nominal............................................................ 60 watts
Minimum.......................................................... 50 watts
FLATNESS .............................................. ±1.5 dB typical
............................................................ ±2.0 dB maximum
FREQUENCY RESPONSE ....................... 0.8 - 3.0 GHz
................................................................. instantaneously
GAIN (at maximum setting) .................. 48 dB minimum
GAIN ADJUSTMENT..................... (Continuous Range)
................................................................. 10 dB minimum
........................................................... (4096 steps remote)
INPUT IMPEDANCE ........................................ 50 ohms
......................................................VSWR 2.0:1 maximum
OUTPUT IMPEDANCE .................... 50 ohms, nominal
MISMATCH TOLERANCE
100% of rated power without foldback. Will
operate . without damage or oscillation with any
magnitude and phase of source and load
impedance.
(See Application Note #27)
MODULATION CAPABILITY
Will faithfully reproduce AM, FM, or pulse
Modulation appearing on the input signal
THIRD ORDER INTERCEPT
See chart. The third order intercept points for
this chart have been determined using two
tones spaced 1 MHz apart. This is typical for
W-CDMA systems. Closer tone spacing such as
60 kHz generally provides about a 1db to 3db
improvement in the IP.
HARMONIC DISTORTION.......................Minus 20 dbc
.................................................................. max at 50 watts
SPURIOUS ......................................... Minus 73 dbc Typ.
PHASE LINEARITY.................
±
1.0 deg/100 MHz, Typ
PRIMARY POWER................... (Selected Automatically)
.........................................................90-132, 180-264 VAC
....................................................... 50/60 Hz, single phase
........................................................... 600 watts maximum
CONNECTORS
RF ..................................................... Type N female
REMOTE INTERFACES
IEEE-488..................................................24 pin
RS-232 ............................. 9 pin Subminiature D
SAFETY INTERLOCK .............. 15 pin Subminiature D
COOLING.....................
Forced air (self contained fans)
MODEL NUMBER RF INPUT RF OUTPUT WEIGHT SIZE(WxHxD
60S1G3 Type N female on front panel Type N female on
front panel
60S1G3M1 Type N female on rear panel Type N female on
rear panel
60S1G3M2 Same as 60S1G3
with enclosure removed for rack mounting
60S1G3M3 Same as 60S1G3M1
with enclosure removed for rack mounting
60S1G3M4 Same as 60S1G3M2 except the gain control knob is removed
and a lock is installed
*60S1G3M5 Type N female on front panel Type N female on
front panel
45 kg (100 lbs) 50.3 x 24.9 x 54.6 cm
19.8 x 9.8 x 21.5 in
45 kg (100 lbs) 50.3 x 24.9 x 54.6 cm
19.8 x 9.8 x 21.5 in
32 kg (71 lbs) 48.3 x 22.2 x 54.6 cm
19.0 x 8.75 x 21.5 in
32 kg (71 lbs) 48.3 x 22.2 x 54.6 cm
19.0 x 8.75 x 21.5 in
32 kg (71 lbs) 48.3 x 22.2 x 54.6 cm
19.0 x 8.75 x 21.5 in
45 kg (100 lbs) 50.3 x 24.9 x 54.6 cm
19.8 x 9.8 x 21.5 in
* The Gain Control can be used to optimize ACP performance.
Loading...