Atec 7520DT, 7550DT, 7564S4 User Manual
Recycled Equipment (410)685-1997 www.recycledequipment.com email: sales@recycledequipment.com
SPECIFICATIONS
Models 7520DT, 7530DT, 7540DT, 7550DT and 7564SA
Functional Specifications
INPUT
Voltage
Frequency
Fuse 6.3 Amp 250V Slo-Blo for 7550DT and 7564SA
DIELECTRIC WITHSTAND TEST MODE
Output Rating 5 KV @ 40 mA for 7550DT and 7564SA,
Output Adjustment Range: 0 - 5 KV AC
Ramp-HI 12mA peak maximum, ON/OFF selectable
Charge-LO Range:
HI-Limit AC Range: 0.00 - 40.00 mA for 7550DT and 7564SA,
115/230 VAC
50/60 Hz
5 Amp 250V Slo-Blo for 75/20/30/40DT
5 KV @ 20mA for 75/20/30/40DT
6 KV @ 10 mA DC for 75/30/40/50DT and 7564SA
Resolution: 1 volt/step
Accuracy:
15
, Single Phase, User selection
5
0 - 6 KV DC
(2
of setting
0.0 - 350.0
0.00 - 20.00 mA for 75/20/30/40DT
5 volts)
A DC or Auto set
Resolution: 0.01 mA/step
Accuracy:
DC Range:
Resolution:
Accuracy:
LO-Limit AC Range: 0.000 - 9.999 mA
Resolution: 0.001 mA/step
Accuracy:
DC Range:
Resolution:
Accuracy:
Arc Detection Range: 1 - 9
Failure Detector Audible and Visual
(2
of setting
0 - 9999
A/step
1
(2
(2
0.0 - 999.9
0.1
(2
A
of setting
of setting
A/step
of setting
A
2 counts)
2 counts)
2 counts)
2 counts)
13
Recycled Equipment (410)685-1997 www.recycledequipment.com email: sales@recycledequipment.com
SPECIFICATIONS
Voltage Display Range: 0.00 - 6.00 KV Full Scale
0.00 - 5.00 KV Full Scale for 7520DT only
Resolution: 10 volt/step
Accuracy:
Current Display Auto Range
AC Range 1: 0.000mA - 3.500mA
Resolution: 0.001mA/step
Range 2: 3.00 - 40.00 mA for 7550DT and 7564SA,
Resolution: 0.01 mA/step
DC Range 1:
Resolution:
Range 2:
Resolution:
Range 3:
Resolution:
Accuracy: All Ranges
DC Output Ripple
4
Ripple RMS at 6 KV DC @ 3.5 mA, Resistive Load
(2
of reading
3.00 - 20.00 mA for 75/20/30/40DT
A - 350.0
0.0
A/step
0.1
A - 3500
300
A/step
1
A/step
(2
of reading
A - 9990
3000
10
2 counts)
A
A
A
2 counts)
Discharge Time
Maximum Capacitive
Load DC Mode
AC Output Wave Form Sine Wave, Crest Factor = 1.3 - 1.5
Output Frequency Range: 60 or 50 Hz, User Selection
Output Regulation
Dwell Timer Range: 0, 0.3 - 999.9 sec (0 = Constant)
Ramp Timer Range: AC 0.1 - 999.9 sec
200 ms
1uF < 1KV
0.75uF < 2KV
0.5uF < 3KV
Accuracy:
(1
of setting
Resolution: 0.1 sec increments
Accuracy:
Resolution: 0.1 sec increments
Accuracy:
1%
5 volts) from no load to full load
(0.1% + 0.05 sec)
DC 0.4 - 999.9 sec
(0.1% + 0.05 sec)
0.08uF < 4KV
0.04uF < 5KV
0.01uF < 6KV
14
Loading...