Atec 7000 User Manual
Series
7000 Precision LCR Meters
USES:
• Production Testing of LCR
Components
• Frequency Response Characterization
of Components
• Component Screening
• Material Testing
• Quality Assurance Testing
• Measuring Dielectric Constant Using
Standard Test Cell
FEATURES:
• Frequency Range 10 Hz to 2 MHz
(7600), 500 kHz (7400)
• 0.05% Basic Measurement Accuracy
• 7 Digit Measurement Resolution
• Programmable Test Voltage and
Current
• Auto Ranging
• Test Setup and Measurement Data
Storage
• Four-Terminal Kelvin Connections
• IEEE-488, RS-232, Handler, and
Parallel Printer Interfaces
• Graphical and Tabular Display of
Swept Frequency, Voltage and Current
Measurements
• Sequence Testing of Up To 6
Individual Tests
• Load Correction
• Binning (15)
• Built-in Automatic Calibration Routine
Introduction
The 7000 LCR Meter is designed to perform precision impedance measurements over a
wide frequency range, 10 Hz to 500 kHz for the model 7400 and 10 Hz to 2 MHz for the
7600. The instrument is capable of measuring 14 different parameters with 0.05% accuracy to meet today’s requirements for component and material testing. The ease of use
and user friendly menu programming makes the 7000 Series ideal for applications in
product development, incoming inspections, or production line testing.
Description
14 Different Impedance Parameters Measure and display any two parame-
ters simultaneously to achieve coverage and flexibility not previously available.
Automatic Test SequencingRun up to six different tests in sequence with a sin-
gle push of the start button. Each test can have different conditions and limits.
Swept Measurements Fast and accurate swept parameter measurements, graphi-
cal or tabular, for verification of component and material response to changes in AC test
frequency, AC test voltage or AC test current, without the need for complex programming
or an external controller.
Program and Data Storage Test setups can be stored and recalled from either
internal memory or from standard DOS formatted 3 1/2” floppy disks. The front panel
can be locked out, with password protection, to ensure procedures are run the same way
every time. Measured data can be stored on a floppy disk and then transferred to PC for
data reduction and analysis.
Load Correction Substantially improves instrument accuracy by performing meas-
urements on a known standard and applying correction to subsequent measurements.
Ideal for repetitive testing of identical devices at like test conditions.
Automatic Calibration ProcedureThe 7000 can be calibrated without return-
ing the unit to the factory using the NIST traceable QuadTech Calibration Kit, reducing
downtime and calibration costs.
Easy to UseLarge LCD graphics display and user friendly menu driven interface allows
the 7000 to be put on line fast, providing useful measurements by operators with little or
no training.
1-800-253-1230
Fax 1-508-485-0295
Intl. 1-508-229-0806
For more information about special purchase,
rent & lease options, call
For more detailed specifications, visit
www.quadtech.com
CE Marked Impedance Analyzer
HIPOT • LCR METERS • MEGOHMMETERS • MILLIOHMMETERS • DECADES • STANDARDS
7400/7600
Measured Parameters: Any two of 14 parameters measured and
displayed simultaneously, user selectable
Test Frequency: 7400 Range: 10 Hz to 500 kHz, continuous
Resolution: 0.1 Hz from 10 Hz to
10 kHz, 5 digits>10kHz
Accuracy: +/-(0.002% + 0.02Hz)
7600 Range: 10 Hz to 2 MHz, continuous
Resolution: 0.1 Hz from 10 Hz to
10 kHz, 5 digits>10kHz
Accuracy: +/-(0.25% + 0.02Hz)
Measurement Speed: 7400 Basic: 40 meas/sec
Enhanced: 8 meas/sec
Extended: 1 meas/sec
7600 Fast: 25 meas/sec
Medium: 8 meas/sec
Slow: 1 meas/sec
Ranging: Automatic, Range Hold or user selectable
Trigger: Internal (automatic), External (RS-232,
IEEE-488.2 or Handler interfaces) and Manual
AC Test Signal: Voltage: 20 mV to 5.0 V (open circuit)
up to 500kHz in 5 mV steps
7600 20 mV to 1.0 V (open circuit)
500kHz-1MHz in 5 mV steps
20 mV to 0.5 V (open circuit)
>1MHz in 5 mV steps
Current: 250 µA to 100 mA (short circuit) in
50 µA steps
(Max. Compliance 3V < 500kHz.
Source Impedance: 25Ω, 400Ω, 6.4kΩ, or 100kΩ, range dependent
DC Bias Voltage: Internal: 2.0 V
External: 0 to +/-200V
0 to +/-500V on 7400A/7600A
Display: LCD Graphics with back light and adjustable
contrast
Result Formats: Engineering or scientific notation
% Deviation from nominal of primary parameter
Deviation from nominal of primary parameter
Pass/Fail
Binning summary
No Display for maximum throughput
Sweep Result: Primary parameter vs. frequency, voltage or
current
Graphical or Tabular Format
Up to 200 measurement points per sweep
Sequencing Result: Displays up to 6 sequential test results, primary
and/or secondary
AutoAcc: Automatic calculation and display of overall
instrument accuracy for selected settings, test
conditions and device under test
Standard Interfaces: IEEE-488.2, RS-232, Handler, Printer Port,
3.5" Disk Drive
Charged Capacitor Protection:
√
8/C for Vmax ≤ 250 V;
√
2/C for Vmax ≤ 1000V
C = Capacitance in farads of the device under test
Additional Fuse Protection on 7400C
Measurement Delay: Programmable from 0 - 1000 ms in 1 ms steps
Averaging: Programmable from 1 - 1000
Median value mode
Data Storage: 40,000 measurements/disk
ASCII format DOS compatible
Program Storage: 125 per disk 25 setups internal
Password protected ASCII format
Calibration: Recommended Calibration Interval 1 year
Complete NIST Traceable Calibration using
QuadTech 7000-09 Cal Kit
Built-in automatic calibration procedure
Usage & Cal Data: Displays last calibration date, standard values
used in calibration and # of hours operation
Self-Test Routine: Verifies critical instrument operation at power-
up or when selected from menu
Contact Check: Time to detect, 2ms
Test Terminals: Front panel, four terminal (BNC) guarded
Mechanical: Bench mount with tilt bail
Dimensions: (w x h x d): 16 x 6 x 14in
(410 x 150 x 360mm)
Weight: 17 lbs (8kg) net, 23 lbs (10.5kg)
shipping
Environmental: Meets MIL-T-28800E, Type 3, Class 5,
Style E & F
Operating: 0 to + 50˚ C
Humidity: <75% for 11 to 30˚ operating
Storage: - 40 to + 71˚ C
Power: • 90 - 250Vac • 47/63Hz
• 100W max
For more detailed specifications, visit www.quadtech.com • For more information about special purchase, rent & lease options, call
1-800-253-1230 • Fax 1-508-485-0295 • Intl. 1-508-229-0806
5 Clock Tower Place, 210 East, Maynard, MA 01754
Product Specifications
PN030087/A1
7400/7600 Precision LCR Meters
7600 LCR Meter
7600-CE LCR Meter, CE Marked
7600A LCR Meter, +/-500V External Bias
7600A-CE LCR Meter, +/-500V External Bias,
CE Marked
7400 LCR Meter
7400-CE LCR Meter, CE Marked
7400A LCR Meter, +/-500V External Bias
7400A-CE LCR Meter, +/-500V External Bias,
CE Marked
7400C LCR Meter, Charged Capacitor
Protection
7400C-CE LCR Meter, Charged Capacitor
Protection, CE Marked
Includes:
Instruction Manual
Power Cord
Calibration Certificate Traceable to NIST
Optional Accessories:
7000-00 Rack Mount Kit
7000-01 BNC Cable Set, 1 meter
7000-02 BNC Cable Set, 2 meters
7000-03 Kelvin Clip Leads
7000-04 Alligator Clip Leads
7000-05 Chip Component Tweezers
7000-06 Axial/Radial Lead Component
Test Fixture
7000-07 Chip Component Test Fixture
7000-08 High Voltage Test Fixture
7000-09 Calibration Kit
Ordering Information
Cs, Cp 00000.01 fF to 9.999999 F ±0.5% ±0.25% ±0.05%
Ls, Lp 0000.001 nH to 99.99999 H ±0.5% ±0.25% ±0.05%
D .0000001 to 99.99999 ±0.005 ±0.0025 ±0.0005
Q .0000001 to 999999.9 ±0.005 ±0.0025 ±0.0005
Z , Rs, Rp, 000.0001 mΩ to 99.99999 MΩ ±0.5% ±0.25% ±0.05%
ESR, Xs
Y , Gp, Bp 00000.01 µS to 9.999999 MS ±0.5% ±0.25% ±0.05%
Phase Angle -180.0000 to +179.9999 degrees ±1.8˚ ±0.9˚ ±0.18˚
Basic Measurement Accuracy*
Parameter Measurement Range Speed
Fast Medium Slow
*At optimum test signal levels, frequencies, DUT values and without calibration uncertainty.
Capacitance (Cs/Cp), Inductance (Ls/Lp), Resistance (Rs/Rp), Dissipation (D) and Quality (Q)
Factors, Impedance Z, Admittance Y , Phase Angle (0-), Equivalent Series Resistance (ESR),
Conductance (Gp), Reactance (Xs), Susceptance (Bp)
Note: s = series, p = parallel, ESR equivalent to Rs
Loading...