Atec 6000-Plus User Manual
USES:
• Production and Compliance Testing of
Appliances, Instruments and Information
Technology Equipment in Accordance
with UL, CSA, IEC, TUV and Other
Standards such as EN60335, EN60950,
EN61010, CSA C22.2 No. 1010.1, UL3111
and UL60950
• Transformer Electrical Safety Testing
• Electric Motor Safety Testing
• Power Supply Safety Testing
• Verification of the Ground Connection on
Products with a Three Prong Power Cord
FEATURES:
• Twin Port - Simultaneous Hipot & GB
• Programmable Output Voltage to 5KV AC
and 6KV DC
• Ground Bond Testing to 30A AC (to 40A
with Optional Transformer)
• Insulation Resistance Measurements from
100kΩ to 50GΩ
• Open/Short Circuit Detection Mode
• Programmable Ramp, Dwell & Test Times
• Storage of 100 Test Setups, 50 Steps Each
• Continuous Leakage Current Monitoring
• Programmable Trip Current to 40mA AC
and 12mA DC
• Front Panel Lockout via Password
• Standard RS-232 & Remote I/O Interfaces
• Optional IEEE-488, Printer Interfaces
• Optional Built-in 8 Channel Scanner
• Optional CaptivATE Automation
Software for G6000 Plus
Introduction
The Guardian 6000 Plus is the industry’s first safety analyzer with simultaneous
Hipot and Ground Bond capability providing a dramatic savings in test time. Five
instruments in one, the G6000 Plus provides AC Hipot, DC Hipot, Insulation
Resistance, Ground Bond and Open/Short measurements from a single test connection. Versatile and packed with features, the G6000 Plus is a cost effective
solution to the full spectrum of electrical safety compliance testing.
Description
AC Hipot: AC dielectric testing over the voltage range from 50V to 5000VAC RMS. The
maximum leakage current of 40mA RMS is ideal for testing devices with high leakage cur-
rents such as power supplies which have large filter or “Y” capacitors for noise reduction.
DC Hipot: DC dielectric testing from 50V to 6000VDC with a resolution of 1V. Leakage
current can be continuously monitored from 0.1µA to 12mA DC.
Insulation Resistance: The G6000 Plus is capable of measuring IR from 100k to 50GΩ
with test voltage from 50V to 1000VDC in 1V steps.
Quick Discharge: In both DC and IR modes, the device under test is discharged through
the HV transformer resulting in a rapid and safe discharge.
Ground Bond: With test current from 1A to 30A in 0.1A steps and programmable current
limits, test time, frequency and open circuit no load voltage, the G6000 Plus provides full
GB testing capability. The offset feature automatically compensates for any lead resist-
ance. A 40A GB option is also available.
Twin Port Technology: This patented feature allows for simultaneous Ground Bond and
Hipot Testing. Decrease test time and increase device through-put.
Open/Short Circuit Detection Mode: Check for Opens and Shorts against a standard
capacitance value, Cs, and have confidence the DUT is properly connected.
Optional Scanners: One internal and/or multiple external scanners may be added to the
G6000 Plus for testing multiple devices simultaneously. Add up to 8 HV channels or a
combination of HV and GB channels.
Standard Interfaces: The Remote I/O and RS-232 interfaces provide remote control and
serial data collection capability for automated applications.
Guardian 6000 Plus
with Revolutionary Twin Port Technology
Electrical Safety Analyzer
Hipot Testers • LCR Meters • Cable Testers • AC/DC Programmable Power Sources
• Megohmmeters • Milliohmmeters
For more detailed information on
specifications, pricing and special
purchase, rent and lease options,
contact us at:
www.quadtech.com
800-253-1230
AC Output Voltage: Range: 50V to 5000V AC, 1V resolution
Regulation: <(1% of setting +5V) at Rated Load
Freq: 50-600 Hz, programmable in 1Hz steps
50~60Hz : 1% + 5 cnts, > 60Hz: 3%+10 cnts
Waveform: Sinusoidal
Voltage Display: Accuracy: ±(1% of reading + 5V)
Resolution: 1Volt
AC Current Display: Total current
Range: 0.001 to 40mA AC
Resolution: 1 or 10µA steps
Accuracy: ±(1% of reading + 5cnt)
High/Low Limit Test: 1µA to 40mA AC
Low limit can be turned OFF
Arc Detection: Programmable 1-20mA,
Pulse Width 40µ, 20µ, 10µ or 4µsec
DC Output Voltage: Range: 50V to 6000V DC, 1V resolution
Regulation: <(1% +5V) at Rated Load
Voltage Display: Accuracy: ±(1% of reading + 5V)
Resolution: 1Volt
DC Current Display: Range: 0.1µ to 12mA DC
Resolution: 0.1, 1 or 10µA steps
Accuracy: ±(1% or reading + 5cnt)
High/Low Limit Test: 0.0001mA to 12mA DC
Low limit can be turned OFF
Arc Detection: Programmable 1-10mA
Pulse Width 40µ, 20µ, 10µ or 4µsec
Insulation Resistance: Range: 50V - 1000V DC
Accuracy: ±5% to ±15% depending upon
voltage and resistance
Voltage Range: 100kΩ - 50GΩ
Voltage Display: ±(1% of reading + 5V)
High/Low Limit Test: 100kΩ - 50GΩ
Low limit can be turned OFF
Ground Bond:
Output Current: Range: 1.0 to 30.0A AC, setting .01A/step; *40A
Regulation: ±(1% of setting + 0.3A)
Accuracy: ±(1% of reading + 3 counts)
Frequency: 50 or 60Hz Selectable
No Load Voltage: 6 to 15 V Programmable
Resistance: Range: 0.1mΩ - 510mΩ , 4 digits
Accuracy: ±(1% of reading + 3 counts)
Resolution: 0.1mV
High Limit: 0.1mΩ to 510mΩ
Start Wait: 0.1 - 99.9sec
Common Features:
Open/Short Circuit Mode: Check for Open & Short against a standard
capacitance value (Cs); <100V, 600Hz
Offset Function: 0 to 100mΩ offset, user selectable
AC Programmable Offset, 0-25mA
Test Time: Ramp: 0.3 to 999s (±20ms), (AC/DC/IR)
Dwell: 0 to 999s (±20ms), (DC only)
Start Wait: 0.1 to 99.9s (±20ms), (GB only)
Test: 0.3 to 999s (±20ms) or Continuous (ALL)
Ramp, Dwell & Start Wait can be set to OFF
Remote Control: Inputs: Start,Stop
Characteristics: Optically Isolated, Low,
Pulse Width >1ms.
Outputs: Pass/Fail/Under Test
Characteristics: Dry Contact relay
Electrical Characteristics: 120V 100mA max.
Logic: Closed if True
Connector: Terminal Strip and 9 pin D Series
Test Setups: 100 Test Setups with 50 Steps each,
13 character Alpha-Numeric Label
Connectors: Front and Rear 4- terminal connection
Display: 320 x 240 enhanced LCD with status indicators
Front Panel Lockout: Key Lock with Password
Fail Lock with Password
Safety Features: Fast Cutoff (<0.4ms) & Fast Discharge (0.2s)
Adjustable Discharge: .05-5.1kV DC
Miscellaneous: Fail Retest; Continue on Fail
PAUSE Mode: Program pause between steps
Indication: Pass/Fail lights, audible sound; Remote, Lock,
Offset & Error status indicators
Buzzer Level: 1,2,3 and Off
Standard Interfaces: RS-232, Remote I/O
Data bits: 8, Stop bits: 1; Parity: None
Selectable Baud Rate: 300 - 19200
Optional Interfaces: IEEE-488, Printer
Dimensions: (w x h x d):17x5.25x18.5in (430x133x470mm)
Weight: 53 lbs (24kg) - Net, 60 lbs (27kg) Shipping
Environmental: Operating: 0 to + 40° C,
Humidity: <75%
Storage: - 20 to + 70° C
Warm-up Time: 1minute
Power: • 90 - 130V AC • 50 or 60Hz
• 200 - 250V AC • 800W max
Guardian 6000 Plus Electrical Safety Analyzer
Includes:
150798 Instruction Manual
S02 HV Lead Set, 1m
G15 Ground Continuity Lead Set
G14 Power Entry Adapter
4200-0300 AC Power Cable
520157 8A 250V Power Line Fuse
520053 4A 250V Power Line Fuse
N/A Calibration Cert. Traceable to NIST
Optional Accessories
N/A Calibration Data
6000-01 Scanner, 8 Channel 5HV,3GC
6000-02 Scanner, 8 Channel 3HV,5GC
6000-03 Scanner, 8 Channel HV
S04 HV Lead Set 2m
S05 Foot Switch
S08 Gun Probe
S09 HV Lead, 1M, Unterminated
S10 HV Lead, 1M, Unterminated
G13 Corded Product Adapter (115V)
G14 Power Entry Adapter
G16 International Power Strip
G24 Scanner Cable (5000 scanners)
G25 Corded Product Adapter (240V)
G38 Printer Interface (replaces IEEE)
G39 IEEE-488 Interface
G43 Rack Mount Kit
G44 Barcode Scanner
G45 40A Ground Bond Transformer
Ordering Information
Guardian 6000 Plus
P r o d u c t S p e c i f i c a t i o n s
*GB to 40A with optional transformer
For more detailed information on specifications, pricing and
special purchase, rent and lease options, contact us at:
www.quadtech.com or 800-253-1230
P/N: 030145/A6
Loading...