Model 395
Specifications
Specifications apply within the specified environmental
conditions after a 20 minute warm-up.
Amplitude
Range: 10 mVp-p to 10 Vp-p into 50 Ω.
Resolution: 3.0 digits.
Accuracy: 25 ± 10° C: ± (1% + 2 mVp-p).
Offset
Range: ± 5 V into 50 Ω.
Resolution: 3 digits.
Accuracy: 25 ± 10° C: ± (1% + 20 mV).
Standard Waveforms
Sine, square, triangle, pulse, pulse trains, DC,
positive/negative ramp, positive/negative haversine,
(sin x)/x, and five noise functions.
Frequency (Sine and Haversine)
Range: 1 µHz to 40 MHz.
Resolution: (Resolution limited by 1 µHz.).
≤ 20 MHz: 10 digits; ± 30 ppm.
> 20 MHz: 4 digits; ± 100 ppm.
Frequency (Square)
Range: 1 µHz to 50 MHz.
Resolution: 4 digits; ± 100 ppm.
Frequency (Triangle)
Range: 1 µHz to 10 MHz.
Resolution:
≤ 100 kHz: 10 digits; ± 30 ppm.
> 100 kHz: 4 digits; ± 100 ppm.
Frequency (Ramp)
Range: 1 µHz to 2 MHz.
Resolution:
≤ 100 kHz: 10 digits; ± 30 ppm.
> 100 kHz: 4 digits; ± 100 ppm.
Frequency (Sin (x)/x)
Range: 1 µHz to 1 MHz
Resolution:
≤ 100 kHz: 10 digits; ± 30 ppm
> 100 kHz: 4 digits; ± 100 ppm
Waveform Quality
Square Transition Time: < 8 ns.
Square Aberrations: < (5% + 20 mV).
Sine Distortion:
< 100 kHz: 0.15% (-56 dBc).
< 5 MHz: No harmonic > -35 dBc.
Arbitrary Waveforms
Sampling Frequency
Range: 100 mS/s to 100 MS/s.
Resolution: 4 digits.
Accuracy: ± 100 ppm.
Waveform Memory Size
64 k points; 256 k points optional.
Minimum Waveform Size: 10 points.
Vertical Resolution: 12 bits.
Output Filters (Selectable): 20 MHz Elliptic (8
pole), 40 MHz Elliptic (8 pole), 10 MHz Bessel (2
pole), no filter.
Waveform Sequencing: Up to 4 waveforms can
be linked. Each waveform can have a repeat (loop)
count of up to 65,535 or run continuously,
conditional upon an external trigger event (repeat
until event true). Additionally, a sequence of
waveforms can be repeated up to 524,287 times or
run continuously.
Pulse Waveforms
Up to 10 pulses may be independently programmed
in a pulse pattern. Parameters that can be
independently programmed for each pulse are rise
time, fall time, width, delay, and amplitude.
For Periods ≤ 655 µs:
Range: 100 ns to 655 µs.
Resolution: 20 ns.
Accuracy: ± 100 ppm.
Rise/Fall:
Fixed: 8 ns.
Variable: 50 ns to 500 µs.
Resolution: 8 ns.
Accuracy: ± 0.1% ± 5 ns
(< 8 ns for fixed rise/fall).
Delay:
Range: -600 to +600 µs.
Resolution: 10 ns.
Accuracy: ± 0.1% ± 5 ns.
Width:
Range: 10 ns to 655 µs.
Resolution: 10 ns.
Accuracy: ± 0.1% ± 5 ns.
For Periods > 655 µs:
Range: 655 µs to 10 s.
Resolution: 4 digits.
Accuracy: ± 100 ppm.
Rise/Fall: 0.1% to 79% of period (or < 8 ns).
Delay: -99.9% to +99.9% of period.
Width: 0.002% to 99.9% of period.
Noise
White (Analog) Noise:
Uniform frequency distribution with programmable
noise bandwidth.
Noise BW Range: 10 mHz to 10 MHz.
Sequence Length:
Standard: 2
With Option 002: 2
n
- 1, n = 6 to 16.
n
- 1, n = 6 to 17.
3
Model 395
Digital Noise:
Digital noise provides a random 0,1 pattern with
programmable sequence length.
Clock Range: 10 mHz to 100 MHz.
Sequence Length:
Standard: 2
With Option 002: 2
Comb:
Uniformly distributed frequency spectra within a
well-defined frequency band.
Start/Stop Range: 1 Hz to 10 MHz.
Number of Lobes: 3 to 256.
Signal-Plus-Noise, Signal-Plus-Comb:
Adds analog noise or comb to any standard or
arbitrary waveform with precise, controlled noise-tosignal ratio.
N/S Ratio: 1% to 99% Vp-p.
Resolution: 1%.
n
- 1, n = 6 to 16.
n
- 1, n = 6 to 17.
Operational Modes
Continuous: The selected waveform is output
continuously at the programmed frequency.
Gated: The selected waveform is output
continuously at the programmed frequency
while the selected trigger signal is true.
Triggered: Upon transition of the selected trigger
from false to true, the number of cycles specified by
the count is output at the specified frequency. Burst
count is programmable from 1 to 1,048,575. (One
to 524,287 for waveform sequence operation.)
Sweep: Frequency sweep.
Triggering
Trigger Sources: 4 trigger sources: External TRIG
IN BNC, internal trigger generator, front panel
manual trigger key, and remote trigger command.
Trigger Level: The trigger level at the TRIG IN
BNC is programmable.
Range: -10 V to +10 V.
Trigger Slope: Positive or negative.
Internal Trigger Source
Range: 200 ns to 1000 s.
Resolution: 100 ns limited by 6 digits.
Sync Output
Sync output can be selected from among the
following 7 sources: waveform sync, trigger signal,
burst done, loop done, sweep marker,
position marker, pen lift.
Modulation
For both standard and arbitrary waveforms.
Internal Frequency Modulation
Carrier Signal
Source: Sine Wave
Center Frequency Range: 0.01 Hz to 40 MHz
Deviation Frequency Range: 0.01 Hz to 40 MHz.
Note: Center frequency plus deviation frequency
must be ≤ 40 MHz.
Modulating Signal
Source: Any waveform except noise, AM, FM, or
pulse.
Modulation Frequency Range: 0.01 Hz to 40 MHz.
Internal Amplitude Modulation
Modes
AM: 0 to 200% modulation
SCM: 200% modulation
Carrier Signal
Source: Sine wave
Carrier Frequency Range: 0.01 Hz to 40 MHz
Modulating Signal
Source: Any waveform except noise, AM, FM, or
pulse.
Modulation Frequency Range: 0.01 Hz to 40 MHz.
External Amplitude Modulation
Normal AM: 0 to 100% modulation.
Suppressed Carrier Modulation (SCM):
± 100% modulation.
Signal Summing
External signals can be summed directly to the
Model 395 output through the SUM IN BNC.
Sweep
Standard and arbitrary waveforms can be swept.
Sweep Start/Stop
Range: 1 mHz to 20 MHz.
Resolution: 4 digits limited by 1 mHz.
Sweep Time
Range: 30 ms to 1000 s.
Resolution: 1 ms.
Sweep Types:
Sweep off, continuous, continuous with reverse,
triggered, triggered with reverse, triggered with
hold, triggered with hold and reverse, and manual.
Sweep Spacing:
Linear and logarithmic.
Outputs
Reference Output (50 Ω):
TTL level into open circuit; > 1.2 Vp-p .
Main Output (50 Ω):
Output may be selected on or off.
AM Input (2.5 kΩ): ± 2.5 V.
Sweep Output (1 kΩ): 0 to 10 V ramp
proportional to completion of sweep.
Sync Output (50 Ω)
Low Level: < 0.4 V into 50 Ω.
High Level: > 2.0 V into 50 Ω.
Rise/Fall Time: < 7 ns.
Inputs
Trigger Input (2 kΩ)
Level: ± 10 V (programmable).
Maximum Frequency: 10 MHz.
Sum Input (600 Ω)
Level: ± 5 Vp-p max.
Bandwidth: > 30 MHz.
Protection: Over-voltage to ± 10 V.
Reference Input (5 kΩ)
Level: 1 Vp-p minimum, 10 Vp-p maximum;
50 Vdc maximum.
Frequency: 10 MHz ± 5%.
General
Remote Operation
RS-232 interface is standard. IEEE-488.2 (SCPI
compatible) GPIB interface is optional.
Environment
Designed to MIL-T-28800C Class 5.
Temperature Range: Operates from 0° to
+50°C: -20° to +70°C for storage.
Dimensions: 35.6 cm (14.00 in) wide,
13.3 cm (5.22 in) high, and 39.4 cm (15.5 in) deep.
Weight: Approximately 7.7 kg (17 lb) net;
10.0 kg (22 lb) shipping.
Power: 90 to 132, 198 to 252 volts rms;
48 to 440 Hz; 1 phase; < 80 VA.
Ordering Information
Model 395: 100 MHz synthesized Arbitrary
Waveform Generator with serial cable and Quick
Start Demo Disk.
Option 001: IEEE-488 Interface/Direct DSO
Waveform Transfer
Option 002: 256k Extended Memory
Option 004: Rack Mount Kit
Model 485: WaveForm DSP, Windows-based
software for creating and editing complex wave
forms.
4