Model 2290-5
Keithley Instruments, Inc. 5 kV Voltage Power Supply Characteristics
28775 Aurora Road
Cleveland, Ohio 44139
1-888-KEITHLEY
http://www.keithley.com
CONDITIONS
This document contains specifications and supplemental information for the Model 2290-5 High Voltage
Power Supply. Specifications are the standards against which the Model 2290-5 is tested. Upon leaving the
factory, the Model 2290-5 meets these specifications. Characteristics, supplemental characteristics, and
typical values are not warranted, apply at 23 °C ± 5 °C, < 70% relative humidity, and are provided solely as
useful information.
CHARACTERISTICS
Voltage range:
Output voltage1 Maximum output current Conditions
50 to +5000 V dc 5.000 mA DC No filter
50 to +3000 V DC 5.000 mA DC Filter 1
50 to +5000 V dc 3.000 mA DC Filter 2
Voltage set accuracy2: ±(0.01% of setting + 2.5 V)
Voltage display accuracy: voltage set accuracy ±1 V, typical (±2 V, maximum)
Voltage resolution: 1 V (set and display)
Voltage limit range: 0 to 100% full scale
Voltage regulation3:
Line: 0.001% for ±10% line voltage change
Load: 0.005% for 100% load change, typical
Output ripple (10 kHz – 100 kHz)4:
0.002% of full scale, V RMS, maximum - No filter
1.0 mV RMS @ 1 kV – Filter 1 or Filter 2
2.0 mV RMS @ 3 kV – Filter 1 or Filter 2
3.0 mV RMS @ 5 kV – Filter 2
Rise time (full load)
5, 6
:
1.5 seconds for 0 V setting to within 1 V of 5000 V DC – No filter
3 seconds for 0 V setting to within 1 V of 3000 V DC – Filter 1
4 seconds for 0 V setting to within 1 V of 5000 V DC – Filter 2
1
The output voltage can be programmed to a voltage lower than 50 V, however, performance below 50 V is not specified.
2
Add ±2.5 V DC when Filter 1 or Filter 2 is enabled.
3
Regulation specifications apply for greater than 25 V DC (with full load), or 50 V DC (with no load). Below these values, the unit may not
regulate correctly.
4
Peak-to-peak values are within five times the RMS value.
5
Current limit set to 105% of full scale.
6
Under resistive load.
Specifications are subject to change without not i ce.
SPEC-2290-5 Rev. A / December 2013 Page 1 of 3
Model 2290-5 High Voltage Power Supply Characteristics
5, 6
CHARACTERISTICS
Voltage range:
Discharge time (full load)
1 second for 5000 V DC to 1 V DC – No filter
3 seconds for 3000 V DC to 1 V DC – Filter 1
4 seconds for 5000 V DC to 1 V DC – Filter 2
Discharge time (no load)5:
<12 seconds (to <50 V DC) – No filter
<30 seconds (to <50 V DC) – Filter 1 or Filter 2
Output stored charge: <0.9 mC maximum
5, 6
:
Settling time
Recovery time
: From 0 to programmed voltage; to within 99.9% of final value within 3 seconds
5, 6
: 120 ms for 40% step change in load current (typical)
Current limit and trip range Filter
0 mA to 5.25 mA No filter or Filter 1
0 mA to 3.25 mA Filter 2
Current set accuracy7: ±(0.01% of setting + 2.5 µA)
Current resolution: 1 µA
Current display accuracy: ±1 µA, typical (±2 µA, maximum)
Stability: ±0.01% per hour; <0.03% per eight hours
Temperature drift: 50 ppm/ºC, 0º to 40º C, typical
Protection: Arc and short circuit protected; programmable voltage and current limits and current trip
Monitor outputs
Output scale: 0 to +10 V to full scale
Current rating: 10 mA maximum
Output impedance: <1 Ω
Accuracy: ±0.2% of full scale with a 100 kΩ load, minimum
Update rate: 8 Hz
7
Add 2.5 µA offset when Filter 1 or Filter 2 is enabled.
Specifications and characteri st ics are sub jec t to change without notice.
Page 2 of 3 SPEC-2290-5 Rev. A / December 2013
Model 2290-5 High Voltage Power Supply Characteristics
External voltage set
Input scale: 0 to +10 V for 0 to full scale
Input impdance: 1 MΩ
Accuracy: ±0.2% of full scale
Update rate: 16 Hz
Output slew rate
5, 6
: <(Rise time + 0.3 seconds) for 0 to full range under full load
GENERAL:
Input power: 55 watts
2290-5 Input voltage: 120 V ±10%, 50 or 60 Hz
2290E-5 Input voltage: 240 V ±10%, 50 or 60 Hz
2290J-5 Input voltage: 100 V ±10%, 50 or 60 Hz
Rear panel connectors:
SHV male (Kings type 1704-1 or equivalent)
Output high-voltage connector GPIB connector
BNC Connector (two): Voltage set/Voltage monitor; Current monitor
Toggle switch: Voltage setting or Voltage monitor
High-voltage safety interlock:
Connector: 3-pin press-in connector, 3M part number: 37103-A165-00E-MB
Pin 1: 5 V nominal out, 1.5 mA maximum out
Pin 2: Input: High-voltage output enabled: 3 – 24 V DC
High-voltage output disabled: <1.2 V DC or open connection
Pin 3: Chassis ground through a 100 Ω resistor
Interface protocol: IEEE-488.1
Operating environment: 0º C to 40º C; non-condensing
Dimensions: 89 mm high x 206 mm wide x 406 mm deep (3.5 in x 8.1 in x 16 in)
Weight: 5.5 kg (12 pounds)
Safety: Conformance to European Union low voltage directive
Warranty: One year
Warm-up time: One hour
Specifications are subject to change without not i ce.
SPEC-2290-5 Rev. A / December 2013 Page 3 of 3
Loading...