Atec 1001WP User Manual

••

• Worldwide Voltage and Frequency Output

••

Test your product for operation anywhere in the world

••

• Easy to Use Test Limit Parameters

••

Check for high and low frequency and voltage conditions

••

• Unique Two Stage Current Limit protec-

••

tion

Starts virtually any load within specified rms rated power

••

• Universal Input from 85V to 264V,

••

47 to 63 Hz

Use in any country, no need to change input power setup

••

• High Efficiency with Input Power Factor

••

Correction

Operates from standard single phase utility power outlets

••

• Lightweight and Portable

••

Easy to move between applications, only 30 lb. (13.6 Kg)

Portable Line Power

Model 1001WP / 1251WP

Test Your Product

for Worldwide Use

International Testing

Products manufactured in one country are often used in another. And, though the utility line power may have similar characteristics, often the frequency and voltage available at the place of manufacture are completely different.

Traditionally, variacs or auto transformers are used for testing products aimed at international markets. This testing covered only different voltage conditions. With the increasing use of microprocessors and logic timing circuits however, products should also be tested at different line frequencies.

ISO 9000 Quality Requirements

Requirements of international quality standards such as ISO 9000 suggest that products should be tested as they are going to be used. These California Instruments supplies represent an new concept to meet the require-

ments of companies who need to test their products for use from nonstandard power. The portable, conveniently sized unit delivers a continuous 1000 VA of power. Operating efficiently from a single phase AC outlet, these products put the convenience of international power at any bench...in the laboratory, the test department, or in the field.

Five Standard Voltage Ranges

Output voltage of 100, 115, 220, 230 and 240 Volts are available to produce all standard world power options. A rear panel switch selects between one of the low voltages and one of the high voltages. The low voltage output is available from a USA Nema 5-15R duplex output. The high voltage output is available from the European CEE 7/7 outlet.This prevents the accidental application of high voltage to equipment configured for USA domestic use. Selection of either 100/

115 V or 220/230/240 V is via a conveniently accessible switch. Any combination of one high and one low voltage option is possible. The selected output voltage is indicated on the front panel. Outlets for other countries are available from the optional International Socket Strip.

50 and 60 Hz Output Frequency

The output frequency can be selected to be either 50 or 60 Hz, independent of the input frequency or output voltage. Testing of product for operation from a different line frequency without first having to design a new power supply or locate a step up or down transformer, is possible. This is especially important for products that rely on line power synchronization. The selected output frequency is also indicated on the front panel.

Simple, Easy to Use Limit Testing

With preset limits at ±10% of the output voltage selected, and ±3Hz of either 50 or 60 Hz, it is extremely easy to test products for operation over normal worst case conditions. The limit switches feature associated LED’s to indicate either the nominal or limit condition so that the output status is immediately clear.

Low Cost Of Ownership

Careful design, the use of modular construction and quality components, all contribute to provide you many years of uninterrupted service. The modular construction allows components or subassemblies to be replaced quickly to minimize downtime.

Ordering Information

Models:

1001WP 1000 VA AC Frequency

Changer.

1251WP 1250 VA AC Frequency

Changer.

Line Cord Options:

Country Part No.

Continental Europe PC11

Australia / New Zealand PC12

UK / Ireland etc. PC13

Denmark PC14

India PC15

Israel PC16

Italy PC17

Switzerland PC19

North America* Note 1

* One North American Line cord is included.

Note 1: PC21 for 1001WP

PC18 for 1251WP

Supplied with:

• North American Line Power Cord

(PC21)

• USA and European line output

mating connector

• Instruction Manual

Specifications* 1001WP 1251WP Unit

Controller

Type Fixed Controls Push Buttons Readout Voltage LED’s

Output

AC Power 1000 1250 VA Voltage Selectable low range 100, 115 V (L-N)

high range 220, 230 , 240 V (L-N) Accuracy ± 1 % of setting Limit Testing - 10%, nominal, + 10% Line & Load Regulation ± 2 % Max.

Total Harmonic Distortion ≤ 1 % typical Output Noise low range ≤ 150 mV

high range ≤ 500 mV

Frequency Selectable 50 or 60 Hz Accuracy ± 1% Limit Testing -3, nominal, +3 Hz Current Current - Steady State low range 9.0 11.0 A

high range 4.5 5.5 ARMS Peak Current low range 29.0 33.0 A

high range 14.5 16.5 A

Protection

Output Over Current yes Short Circuit yes Over Temperature yes Over Voltage yes

Input

Line Voltage 2 wire + GND 100 - 240 ±10 % VRMS Input Current < 15 < 20 ARMS Line Frequency 47 - 63 Hz Holdup Time 20 ms Power Factor > 0.95 typical Line Cord Input Connector IEC320/C19

Physical

Regulatory CE, UL, CSA Dimensions HxWxD 8.25 x 8.5 x 17.5 inches

HxWxD 210 x 216 x 445 mm Weight 30 / 13.6 lbs / kg Operating Temp. 0-40 / 32-104 °C / °F

* Specifications are warranted for an ambient temperature of 23° + 5° C and apply after a 30

minute warmup period.

RMS

Contact California Instruments:

Toll-Free: 800-4AC-POWER

800-422-7693

FAX: 858-677-0940

Email: sales@calinst.com

Web page: http://www.calinst.com

9689 Towne Centre Drive, San Diego, CA 92121-1964 (858) 677-9040 FAX : (858) 677-0940