Model 1000A225, M1
1000 Watts CW
10kHz–225MHz
The Model 1000A225 is a self-contained, air-cooled, broadband, completely solid-state amplifier designed for
applications where instantaneous bandwidth and high gain are required. Push-pull MOSFET circuitry is utilized in all high
power stages in the interest of lowering distortion and improving stability.
The Model 1000A225 is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the
amplifier. The DCP uses a 3-¾ inch diagonal graphic display, menu assigned softkeys, a single rotary knob, and four
dedicated switches (POWER, STANDBY, OPERATE and FAULT/RESET) to offer extensive control and status reporting
capability. The display provides operational presentation of Forward Power and Reflected Power plus control status and
reports of internal amplifier status. Special features include a gain control, internal automatic level control (ALC) with front
panel control of the ALC threshold and RF output level protection. RF Sample Ports are included to monitor forward and
reverse power.
All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, and RS-232 hard
wire and fiber optic and USB. The bus interface connectors are located on the back panel and positive control of local or
remote operation is assured by a keylock on the front panel of the amplifier.
High-efficiency, universal-input, power-factor-corrected switching power supplies provide DC to all internal subassemblies.
Housed in a stylish, contemporary enclosure, the Model 1000A225 provides readily available RF power for typical
applications such as RF susceptibility testing, antenna and component testing, watt meter calibration, particle accelerators,
plasma generation, communications and use as a driver for higher power amplifiers.
The export classification for this equipment is EAR99. These commodities, technology or software are controlled for export
in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.
1600
Model 1000A225 Typical Power Output
1400
1200
1000
800
Power (Watts)
600
400
200
0
0.001 0.01 0.1 1 10 100 1000
Freq (MHz)
P1dB
PSat
Approved for public release by AR RF/Microwave Instrumentation 040412
160 School House Road Souderton, PA 18964-9990 • 215-723-8181 • www.ar-worldwide.com Page 1 of 2
RATED OUTPUT POWER ............................................... 1000 watts
INPUT FOR RATED OUTPUT .......................................... 1.0 milliwatt maximum
POWER OUTPUT @ 1 dB COMPRESSION ..................... 900 watts nominal
700 watts minimum
FREQUENCY RESPONSE ............................................... 10 kHz–225 MHz instantaneously
GAIN (at maximum setting) ........................................... 60 dB minimum
FLATNESS ..................................................................... ± 3.0 dB maximum
± 1.0 dB with internal leveling
GAIN ADJUSTMENT (continuous range) ......................... 20 dB minimum
INPUT IMPEDANCE ....................................................... 50 ohms, VSWR 1.5:1 maximum
OUTPUT IMPEDANCE ................................................... 50 ohms nominal
MISMATCH TOLERANCE ............................................... 100% rated power without foldback up to 6.0:1 mismatch above which may
MODULATION CAPABILITY ........................................... Will faithfully reproduce AM, FM or Pulse modulation appearing on the input
HARMONIC DISTORTION ............................................. Minus 20 dBc maximum at 750 watts
THIRD ORDER INTERCEPT POINT .................................. 68 dBm typical
RF POWER DISPLAY ...................................................... 0–2000 watts full scale
RF RISE/FALL TIME ........................................................ 10 nanoseconds maximum
PRIMARY POWER .......................................................... 187–264 VAC
47–63 Hz, single phase
5,000 watts maximum at .95 P.F. typical
CONNECTORS
RF Input ................................................................. See Model Configurations
RF Output .............................................................. See Model Configurations
Forward RF Sample ................................................ Type BNC female on front panel
Reverse RF Sample ................................................. Type BNC female on front panel
Remote Control ...................................................... 24 pin female GPIB/IEEE-488, 9-pin RS-232 and USB connectors on rear panel
Remote Control (Fiber Optic) .................................. ST connector. Tx and Rx RS-232.
Safety Interlock ....................................................... 15 pin female Type D on rear panel
IEEE-488 (GPIB) INTERFACE & RS-232 ........................... Allows control of all amplifier functions and monitoring of all status indications.
COOLING .................................................................... Forced air (self contained fans), internal self-contained liquid
WEIGHT (maximum) ..................................................... 127 kg (280 lb)
SIZE (W x H x D) ............................................................ 56.1 x 109.2 x 88.9 cm (22.1 x 43.0 x 35.0 in)
Model Number RF Input RF Output
1000A225 N female, rear panel 7-16 DIN female rear panel
1000A225M1 N female, front panel 7-16 DIN female front panel
SPECIFICATIONS, MODEL 1000A225
limit to 500 watts reflected power.
signal.
MODEL CONFIGURATIONS
Page 2 of 2