Atec 1000 User Manual
Guardian
1000 Series
Hipot Testers
USES:
• Production Testing of Appliances,
Instruments and Information
Technology Equipment in Accordance
with UL,IEC,TÜV and Other
Standards such as EN60335, EN60950,
EN61010, CSA C22.2 No. 1010.1,
UL3111 and UL1950
• Transformer Electrical Safety Testing
• Electric Motor Safety Testing
• Testing a Variety of Electronic
Components
FEATURES:
• Real and Total Current; 30mA AC,
10mA DC
• Programmable Output Voltage to 5kV
AC and 6kV DC
• Resistance Measurements from
0.1MΩ to 50GΩ
• Programmable Ramp, Test & Fall
Times
• Programmable High & Low Limits
• Open/Short Circuit Check
• Ground Continuity Check with
1ohm Limit
• Arc Detection with Programmable
Limit
• Quick Discharge of DUT in IR and
DC Hipot
• Storage of 99 Tests Setups with
Multiple Steps per Measurement
• Front Panel Lockout
• Remote I/O & RS232 Interfaces, Std.
• IEEE-488 or Printer Interfaces, Opt.
• 8 Channel Scanner (1030S)
Introduction
A complete dielectric testing solution, with three models from which to choose. The
Guardian 1010 for AC Hipot testing, the Guardian 1030 for AC/DC Hipot testing and
insulation resistance (IR) measurements; and the Guardian 1030S which combines
both AC and DC Hipot tests and IR measurements with eight HV scan channels. All
models have Open/Short Circuit detection and Load/Line regulation to ensure proper
device connection and measurement integrity. The digital display and user friendly
controls allow test parameters and limits to be set without the high voltage activated.
Description
The Guardian 1010 AC Hipot Tester performs AC dielectric withstand tests. The test
voltage can be programmed in the range from 50VAC to 5kVAC with a resolution of
1V. The maximum total output current is 30mA.
The Guardian 1030 AC/DC/IR Hipot Tester has all the features of the Guardian
1010 with the addition of DC hipot and IR measurement capabilities. The test voltage
can be programmed in the range from 50VDC to 6kVDC with a resolution of 1V. The
maximum total current is 10mA. The IR measurement range is from 0.1MΩ to 50GΩ
with test voltages from 50 to 1000VDC.
The Guardian 1030S AC/DC/IR/SC Hipot Tester has all of the features of the
Guardian1030 plus eight HV Scan Channels for multi-point testing.
Real and Total Current Measurement: Accurately measure the leakage current of
highly capacitive devices by separating the real and reactive current.
Ground Fault Interrupt (GFI): Provides an extra level of safety for the operator and
equipment. The instrument shuts down when the current balance exceeds 0.5mA.
G1000 Series units also have an interlock for use with palm switches, light curtains,
hoods and other safety switches.
Quick DUT Discharge: In both the DC hipot and IR tests the device under test is discharged back through the HV transformef for a rapid and safe discharge.
Ground Continuity Check: All of the Guardian 1000 Series units have a ground continuity check feature to determine that the resistance, between the ground blade of the
power cord and any exposed metal on the product, is less than 1 ohm.
Open/Short Circuit Mode:All Guardian 1000 Series models have OS mode to detect
connection of the device in order to prevent false readings. Open ensures the device
under test is connected properly and Short ensures the device is not shorted prior to
applying the high voltage. The Open value is programmable from 10-100% and the
Short value from 100-500%.
Multi-Purpose AC/DC/IR/SC Hipot Testers
G1030S: EMC only
For more detailed information on
specifications, pricing and special
purchase, rent and lease options,
contact us at:
www.quadtech.com
800-253-1230
Hipot Testers • LCR Meters • Cable Testers • AC/DC Programmable Power Sources
• Megohmmeters • Milliohmmeters
Guardian 1010, 1030 & 1030S
AC Output Voltage: Range: 50V to 5000V AC
Resolution: 1Volts/step
Frequency: 50/60 Hz selectable
Waveform: Sinusoidal
Regulation: +/-(1% of setting +5V)
Voltage Display: Accuracy: +/-(1% of reading + 5V)
Resolution: 1 Volt
AC Current Display: Total and Real Current
Range: 0.001mA to 30mA AC
Resolution: 1µA
Accuracy:+/-(1% of reading + 5cnt) Total
Accuracy:+/-(5% of reading + 20cnt) Real
High/Low Limit Test: Range: 0.001mA to 30mA AC
Low limit can be turned OFF
Guardian 1030 & 1030S
DC Output Voltage: Range: 50V to 6000V DC
Resolution: 1Volts/step
Regulation: +/-(1% of setting +5V)
Voltage Display: Accuracy: +/-(1% of reading + 5V)
Resolution: 1 Volt
DC Current Display: Range: 0.0001mA to 10mA DC
3 Ranges: .0001mA - 0.3mA,
0.31mA - 3mA, 3.1mA - 10mA
Accuracy:+/-(1% of reading + 5cnt)
High/Low Limit Test: 0.1µA to 10mA DC
Low limit can be turned OFF
Charging Current: 10mA max
Insulation Resistance: Range: 0.1MΩ - 50GΩ
1M - 1G: +/- (5% + 10 cts), >500V
1G - 10G: +/- (10% + 10 cts), >500V
10G - 50G: +/- (15% + 10 cts), >500V
0.1M - 1G: +/- (10% + 10 cts), <500V
IR Output Voltage: Range: 50V to 1000V DC
Accuracy: +/-(1.5% of setting +5V)
High/Low Limit Test: 0.1MΩ - 50GΩ
High limit can be turned OFF
Guardian 1030S
Scan Channels: 8 HV Scan Channels
Test Cables: 8 Custom Banana (unterminated)
Common Features
Open/Short Detection: Voltage <100V, Frequency: 600Hz
Open: 10-100%; Short: 100-500%
Common Features
Arc Detection: Arc Level: adjustable OFF or
1mA - 15mA AC & 10mA DC
Arc Duration: > 10µs
Indication: Pass/fail lights, audible sound
Time: Ramp: 0.1 to 999s (+/-20ms), OFF
Test: 0.1 to 999s (+/-20ms), Continuous
Fall: 0.1 to 999s (+/-20ms), OFF
Quick Discharge: Discharge of voltage across DUT back
through the HV transformer
Output Cutoff: <0.4msec after limit exceeded
Ground Continuity: High Limit: 1Ω
Accuracy: +/-0.2Ω
Ground Fault Interrupt: Automatic instrument shutdown for
current imbalance >0.5mA
Standard Interfaces: RS232, Remote
Inputs: Start, Stop and Interlock
Characteristics: 24V Active Low,
Pulse Width >20ms.
Outputs: Pass/Fail/Under Test
Characteristics: Dry Contact relay
Ele. Characteristics: 120V 100mA max.
Logic: Closed if True
Connector: 9 pin Male D-Series
Optional Interfaces: IEEE 488 or Printer
Test Setups: 99 Memory Locations, 99 Steps, max 500
Connectors: Front Connection (HV and RTN)
HV OUTPUT (Custom Banana)
RTN/LOW (Binding Post)
Front Panel Lockout: Key press with or without memory recall
Miscellaneous: Zero Offset
Dimensions: (w x h x d):12.8x4.2x16in
(320x105x400mm)
Weight: 1010 & 1030: 30.5 lbs (14kg) net,
36 lbs (16.5kg) ship
1030S: 32.5 lbs (15kg) net,
38 lbs (17.5kg) ship
Environmental: Meets MIL-T-28800E, Type 3, Class 5
Operating: 0°C to + 40°C
Humidity: <70%
Storage: - 10°C to + 60°C
Power: •90 - 130V AC •50 or 60Hz
•200 - 250V AC •500W max
P r o d u c t S p e c i f i c a t i o n s
Guardian 1010 AC Hipot Tester
Guardian 1030 AC/DC/IR Hipot Tester
Guardian 1030S AC/DC/IR/SC Hipot Tester
Includes:
150665 Instruction Manual
700070 Power Cable
S02 Test Leads
700100 Ground Continuity Lead
Calibration Certificate Traceable to NIST
Lead Set: (8) Unterminated (1030S only)
Optional Accessories:
Calibration Data
S02 HV Lead Set, 1m, (std w/unit)
S03 Corded Product Adapter(115V)
S04 HV Lead Set, 2m
S05 Foot Switch
S06 High Voltage Probe
S07 Power Entry Adapter Cable
S08 Gun Probe
S09 HV Lead, 1 meter, unterminated
S10 HV Lead, 2 meters, unterminated
S11 Gun Probe with remote start
S12 Load Box, resistive
S14 Load Box, custom resistors
S15 Interconnection Cable to S50
G16 International Power Strip
G25 Corded Product Adapter (240V)
G38 Printer Interface(replaces IEEE)
G39 IEEE-488 Interface
G40 Scanner Lead Set (8), with Clips
for G1030S only
Ordering Information
For more detailed information on specifications, pricing and
special purchase, rent and lease options, contact us at:
www.quadtech.com or 800-253-1230
P/N 030093/A6
Loading...