Operating Instructions & Parts Manual
Folding Creeper Seat
Model
ATD-81045
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
!
U.S. Patent Nos. 6,969,077
Capacity
450 lbs.
! ADVERTENCIA
• Leer, comprender, y seguir las instrucciónes antes de utilizar el aparato.
• El manual de instrucciónes y la información de seguridad deben estar comunicado en lengua del operador
antes del uso.
• No seguir estas indicaciónes puede causar daños personales o materiales.
ATD Tools, Inc.
160 Enterprise Drive, Wentzville MO 63385
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
Printed in China
ATD-81045-M3 04/09
SAFETY and GENERAL INFORMATION
Head Cushion
Head Frame
Middle Frame
Rear Frame
Locking Pin
(Not Shown)
Casters (4)
Casters (2)
Fasteners (4)
For your safety, read, understand, and follow the information provided with and on this folding creeper. The owner
and operator shall have an understanding of this product and safe operating procedures before attempting to use.
The owner and operator shall be aware that use of this product may require special skills and knowledge. Instructions
and safety information shall be conveyed in the operator’s native language before use of this product is authorized.
Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of
the product. If any doubt exists as to the safe and proper use of this product, remove from service immediately.
Inspect before each use. Do not use if there are broken, bent, cracked or damaged parts (including labels). Any
folding creeper that appears damaged in any way, or operates abnormally shall be removed from service immediately.
If the folding creeper has been subjected to a shock load (a load dropped suddenly, unexpectedly upon it), immediately
discontinue use until it has been inspected by an ATD authorized service center. It is recommended that an annual
inspection be done by qualied personnel. Labels and Operator’s Manuals are available from manufacturer.
PRODUCT DESCRIPTION
This device is designed to be folded in a ‘Z’ shape for use as a mechanics seat or unfolded for use as a mechanics
creeper. It is intended to be used to support and move, along a smooth and level surface, rated capacity loads consisting of a single person weighing no more than *450 lbs. for the purpose of performing automotive maintenance
or service. This device is not intended, designed or engineered to be used for any other purpose.
*Rated Capacity: One (1) person weighing 450 lbs. or less- * includes person, tools, equipment, personal items
SPECIFICATIONS
Model Capacity Seat Size Creeper Size
ATD-81045 *450 lbs. ~14” x 12-1/4” ~40”
Do not use this device for any purpose other than that for which it is expressly intended.
!
Figure 1 - Model ATD-81045 Components
2
!
To avoid personal injury and property damage:
• Read, understand, and follow all printed materials provided with and on this product before use.
• Do not exceed rated capacity! Rated capacity is: 450 lbs. (includes person, tools, equipment, personal items).
• Sit down gently! Avoid shock loads caused by jumping or falling onto seat.
• Do not stand on seat.
• Beware of pinch and crush hazards when folding and unfolding.
• Keep out of the reach of children! This device is not appropriate for children’s use.
• Use on smooth, level surfaces only.
WARNING
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and Figure 1 illustration. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement parts.
Contents: 1 creeper body, 6 casters, 4 fasteners
Dimensions: 40” X 18” X 7-1/2”
ASSEMBLY INSTRUCTIONS (see Figure 1)
1. Carefully unfold the creeper as seen in Fig. 1.
Keep hands away from pinch and crush points
!
that are created while folding and unfolding!
2. Use a suitable open-end wrench to attach the head frame casters to Head Frame. Hand tighten with open end
wrench.
3. Use a 5 mm hex-key to attach the remaining casters to the Rear Frame. Insert the threaded fasteners from
above, the casters from below (as seen in Fig. 1), then hand tighten with hex key.
4. Attach Parts Tray to Rear Frame channel as seen below.
OPERATING INSTRUCTIONS (Refer to Fig. 2, 3)
Little instruction is necessary for the safe and proper use if all warning information is understood and followed.
Keep hands away from pinch and crush points that are created during use! Be alert and sober when
!
using this product! Never operate this equipment when under the inuence of drugs or alcohol.
To transform creeper into seat position
Figure 2
Step 1. Locate, then unlock the spring loaded Lock
Pin by pulling out until disengaged, at the same time
ip the Head Frame and Middle Frame upward and
back towards the Rear Frame section until the Lock
Pin can engage the Creeper Seat Locking Sleeve
(Fig. 3). Ensure Lock Pin is fully engaged.
To transform seat into creeper position
Figure 3
Step 3. Unlock the spring loaded Lock Pin by pulling out until disengaged, then reverse steps 1, 2 to
convert Creeper Seat into Creeper.
Step 2. Flip the Head Frame forward until horizontal.
3
CARE AND MAINTENANCE
MAINTENANCE
Little maintenance is required of this device. Wipe clean as needed. Use mild upholstery cleaner (not caustic) to
clean seat as needed.
Never add lubricant to casters!
!
REPLACEMENT PARTS LIST
Item Part No. Description Qty
1 81045-1 Caster w/ fastener 4
2 81045-1A Caster w/ nut 2
3 81045-2 Head Cushion 1
4 81045-3 Body Cushion 1 1
5 81045-4 Body Cushion 2 1
Item #3
Head Cushion
Item #2
Casters w/nut (2)
Item #4
Body Cushion 1
Item #1
Casters w/fasteners (4)
Item #5
Body Cushion 2
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, ATD Tools, Inc. will repair or replace, at its option, without
charge, any of its products, which fails due to a defect in material or workmanship under normal usage. This limited
warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to ATD Tools, Inc. Warranty Service Department, 10939 N. Pomona Ave., Kansas City, MO 64153.
Except where such limitations and exclusions are specifically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) ATD Tools, Inc. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state.
4
Loading...