ATD Tools ATD-80133 User Manual

Features and Specifications

• 7.4V 1400MAh Li-ion rechargeable battery - twice the life expectancy compared to regular rechargeable batteries.

• Cordless, 30 super bright LED’s provide long, dependable service life.

• Shatterproof and shock resistant protective tube.

• Swivel hooks make this light easy to attach anywhere - horizontally or vertically.

• The ATD-80133 Saber Li-Ion Worklight provides an average runtime of 6 hours per charge.

• 9V 500mA AC to DC adaptor can be used with110VAC power source.

• OPTIONAL DC adaptor (ATD-80131) can be used with your vehicles 12V power outlet.

• Red light on adaptor (indicates charging), green light on adaptor (indicated fully charged), blue light on led board

• Overcharge and over discharge protection.

• Automatically shuts off soon after low battery indicator lights up.

Charging Instructions

The battery is only 50% charged before shipping. Fully charge your ATD Saber Worklight before use.

Be sure your ATD Saber Li-Ion Worklight is turned off, as it will not charge while in use, and then plug the AC charging
unit into the wall and into the bottom of your ATD Saber Li-Ion Worklight. The LED indicator on the wall charging unit
will change from red to green when the ATD Saber Li-Ion Worklight

The blue indicator light on the LED board will come on when the battery is almost discharged, giving you a few minutes
of light left before the light goes completely out. It will not fade out, it will simply turn off.

The ATD Saber Li-Ion Worklight
Charging time for a full charge is approx 3 hours. Be sure to only use the AC adaptor (supplied) or the DC adaptor
(optional) with the light. Use of any other 110VAC or 12VDC adaptor can cause battery damage.

The ATD Saber Li-Ion Worklight
battery.

Operating Environment

• The ambient temperature range for working is 14°F-122°F (-10°C-50°C).The ambient temperature range for

• Keep your ATD Saber Li-Ion Worklight

• Keep your ATD Saber Li-Ion Worklight

• Avoid bumping or dropping your ATD Saber Li-Ion Worklight

ATD-80133 Instructions

(indicates low battery).

is fully charged.

will need to be recharged when the blue indicator light on the LED board comes on.

needs to be fully charged at least every 6 months to maintain the performance of

charging is 32°F-104°F ( 0°C-40°C). Charging the battery at a lower or higher temperature range will damage the
battery.

away from heat sources.
away from acids and alkalines.

U.S. Patent Number D548,382

LED board replacement instructions

• When repairing your ATD Saber Li-Ion Worklight, do not allow any metal to come in contact with the internal battery
pack or the PC board and its components.

• Turn the ATD Saber Li-Ion Worklight

• Remove end cap (2) from end of tube (3) using care not to crack the tube (3).

• Pull the LED PC board (8) from top of the tube (3).

• Disconnect the wiring connector from the LED PC board, and reconnect it to a new PC board (8).

• Carefully slide the PC board assembly (8) back into clear tube (3) and replace the end cap (2).

The ATD Saber Li-Ion Worklight is NOT waterproof, and is NOT intended to be used in showers, saunas, or
any other potentially wet locations. Keep the ATD Saber Li-Ion Worklight

electrical appliance when they fall into the water can be fatal.

ANY

The ATD Saber Li-Ion Worklight is to be used for general indoor lighting. It is NOT intended to be used in potentially
hazardous locations such as near flammables or in explosive atmospheres.

off.

away from sinks, tubs, showers, etc. Retrieving

Your ATD Saber Li-Ion Worklight has a built in automatic discharge shut off feature that prevents the battery from
becoming fully discharged, thus extending the battery life.

Your ATD Saber Li-Ion Worklight
it is in use however.

The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It must be understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.

can be used when plugged into the AC adapter for recharging. It will not recharge while

U.S. Patent Number D548,382