Page 1
Model: ATD-7462
Capacity: 2 Ton
OWNER’S MANUAL
2-TON SCISSOR JACK
Model Capacity Min.
Height
Max
Height
Compressed Dimensions Saddle
Diameter
Shipping
Weight
ATD-7462 2 Ton 5” 13” 12.25” x 4.25” x 5.125” 5-1/8” x 2” 7.9 Lbs.
Contents:
Page: 1.
2. Setup, Opera
3. Inspec
on, Storage & Troubleshoo ng
4. Exploded View & Warranty Informa
on & Preven ve Maintenance
on
SAFETY & WARNING INFORMATION
This is the safety no a on
symbol. This symbol will no
of any poten
Please follow all instruc
follow this symbol to avoid possible
injuries or death.
al injury hazards.
fy you
ons that
Indicates a hazardous
on. If proper steps are
situa
not followed, death or
serious injury could result.
WARNING: This product may contain chemicals, including lead, known to the State of California
to cause cancer, birth defects or other reproductive harm. Wash hands after handling.
Made in China to ATD Tools, Inc. Specications
Visit us at www.atdtools.com
ATD7462_rev_0417
1
Page 2
Model: ATD-7462
Capacity: 2 Ton
IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE
Before oper ng this device, be sure to read all content within this manual, ensuring that you understand the
oper
ng procedures, maintenance requirements and all safety warnings. The owner and/or operator shall have
an understanding of the product, its opera
this device. Safety informa
product and safety instruc
by the purchaser/owner or his designee, making sure that the operator comprehends their contents.
on shall be emphasized and understood. If the operator is not Ňuent in English, the
ons shall be read to and discussed with the operator in the operator’s n ve language
ng characteris cs, and safety opera ng instruc ons before oper ng
ACTIONS TO HELP PREVENT DANGEROUS SITUATIONS
x Study, understand and follow all instruc ons before opera ng this device.
x Do not exceed the rated capacity stated.
x Use only on hard level surfaces.
x Use only for emergency
x Never get beneath the vehicle when it is supported by the jack.
x If the vehicle is pushed oī the jack, discard jack. Do not reuse.
x Li
x No alter
x This jack should be used as an emergency device only.
x Failure to heed these markings may result in serious personal injury / property damage.
SETUP
x Prior to each use, visual inspec on (See Pg. 3) shall be made to the device by checking for abnormal
x Consult the vehicle owner’s manual to determine the loca
x Ac
x Be sure to set the vehicle in park with the emergency brake on and wheels securely chocked in both
x Be sure that the vehicle and the jack are on a hard, level surface .
x Follow the
only on areas of the vehicle as speciĮed by the vehicle manufacturer.
ons shall be made to this product.
ons, such as cracked welds, leaks, and damaged, loose, or missing parts.
condi
vate hazard warning Ňashers and turn oī the vehicle.
ons.
direc
re-changing procedures or
manufacturer’s owner’s manual.
re changing or for moun ng re chains.
on of li points.
re-chain moun ng procedures speciĮed in the vehicle
ASSEMBLY
x A ch the handle assembly to the eyehole and use as a handle to raise and lower the jack.
LIFTING
x Turn the handle counter-clockwise to lower the jack to its lowest posi
x Posi
x Begin li
x Ensure that the saddle is in the correct posi
x Li
on the jack under the speciĮed li point.
ing by turning the handle assembly clockwise.
ing point before vehicle contact has been made.
li
only to the point that the desired outcome can be reached. Do not over extend this jack.
on.
on and located under a vehicle manufacturer designated
2
Page 3
Model: ATD-7462
Capacity: 2 Ton
LOWERING
ͻ Turn the handle slowly counter-clockwise to lower the jack to its lowest posi on.
ͻ Do not get under or let anyone get under the vehicle while lowering.
ͻ Once completely lowered, remove the unit and return it back to its storage loc
MAINTENANCE
Lubrica on and Cleaning
x Periodically clean and lubricate all moving parts and pivot points.
Damaged Equipment
Any jack that appears to be damaged in any way, is found to be worn, or operates abnormally SHALL BE REMOVED
FROM SERVICE. It is recommended that in this event, the jack be replaced. No repairs are authorized and no parts
are available for this jack.
Altera ons
Because of poten al hazards associated with this type of equipment, no alter ons shall be made to the product.
A achments and Adapters
dŚĞƌĞĂƌĞŶŽĂƩĂĐŚŵĞŶƚƐŽƌĂĚĂƉƚĞƌƐĂǀĂŝůĂďůĞŽƌĂƵƚŚŽƌŝnjĞĚĨŽƌƵƐĞǁŝƚŚƚŚŝƐũĂĐŬŶLJƵƐĞŽĨĂƩĂĐŚŵĞŶƚƐŽƌ
adapters could result in property damage, injury or death.
INSPECTION
x Visual inspec on shall be made before each use of the device by checking for abnormal condi ons, such
as cracked welds, leaks, and damaged, loose, or missing parts.
x Other inspec
x This device shall be inspected immediately if the device is believed to have been subjected to an abnormal
load or shock. It is recommended that this inspec
x Owners and/or operators should be aware that repair of this equipment may require specialized
knowledge and facili
ƋƵĂůŝĮĞĚƐĞƌǀŝĐĞĂŶĚƌĞƉĂŝƌĨĂĐŝůŝƚLJĂŶĚƚŚĂƚĂŶLJĚĞĨĞĐƟǀĞĚĞĐĂůƐŽƌƐĂĨĞƚLJůĂďĞůƐďĞƌĞƉůĂĐĞĚǁŝƚŚƚŚĞ
supplier’s speciĮed parts.
ons shall be made per product opera ng instruc ons.
on be made byĂƋƵĂůŝĮĞĚƐĞƌǀŝĐĞĂŶĚƌĞƉĂŝƌĨĂĐŝůŝƚLJ
es. It is recommended that an annual inspec on of the product be made by a
on.
STORAGE
This Jack should be stored in a dry locĂƟon.
TROUBLESHOOTING
Symptom Possible Causes Solu on
The jack will not lower
completely.
Jack will not hold the load.
Jack will not rise.
Jack will not li the load.
Jack arm will not lower.
1. The threads on the adjustment
rod may be bent not allowing the
jack to fully lower.
1. Overall damage to the jack. 1. Replace the jack.
1. Check to see if there is damage to
2. Lubrica
1. The weight of the unit being li ed
is too high.
1. The threads on the adjustment
rod may be bent not allowing the
jack to fully lower.
the adjustment rod.
on needed on moving
components
1. Transfer the weight to another
jack and replace the jack.
1. Replace the jack
2. Lubricate moving parts and test
func on again.
1. Decrease the weight of object
being li
capacity jack.
1. Replace the jack.
ed or purchase a higher
3
Page 4
Model: ATD-7462
Capacity: 2 Ton
Part Number Description Qt’y
LB020-1
Handle Assembly 1
* Items not iden Įed by part number are not available for replacement.
WARRANTY INFORMATION
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from your purchase date, ATD Tools, Inc. will repair or replace (at its op on) without
charge, your ATD product if it was purchased new and the product has failed due to a defect in material or workmanship
which you experienced during normal use of the product. This limited warranty is your exclusive remedy.
To access the beneĮts of this warranty, contact ATD at 1-844-364-9922 for conĮrma
applies. Therea
department.
If this ATD product is altered, abused, misused, modiĮed, or undergoes service by an unauthorized technician, your
warranty will be void. We are not responsible for damage to ornamental designs you place on this ATD product and such
ornamenta
cover scratches, superĮcial dents, and other abrasions to the paint Įnish that occur under normal use.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defec
(2) ATD is not liable for any incidental damages, including but not limited to, lost proĮts and unforeseeable
consequences.
(3) The repair and replacement of this product under the express limited warranty described above is your
exclusive remedy and is provided in lieu of all other warran
including implied warran
disclaimed and, if disclaimer is prohibited, these war ran
of this product.
Some states’ laws do not allow limited dura
ons on incidental or consequen al damages. You should consult the law in your state to determine how your
limita
rights may vary.
er, you may be advised to return the product under warranty, freight prepaid, to the ATD service
on should not cover any warnings or instruc ons or they may void the warranty. This warranty does not
ve product as described above.
es, express or implied. All other warran es,
es and warran es of merchantability or Įtness for a par cular pur pose are
es are limited to one year from your date of purchase
ons on certain implied warran es and some states’ laws do not allow
ATD Tools, Inc.
160 Enterprise Drive
Wentzville, MO 63385
Toll Free Service Number 1-844-364-9922
Printed In China
on that this warranty
4
Loading...