Page 1
Swift Lift
Hydraulic Service Jack
Operating Instructions & Parts Manual
Model Number
ATD7341
Capacity
3-1/2 Ton
U.S. Patent No's. 5,946,912 • 6,199,379
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
!
Obey all safety messages that follow this symbol to avoid possible injury or death.
160 Enterprise Drive, Wentzville, MO 63385
Read this manual and follow all the Safety Rules and Operating Instructions before using this product.
! WARNING
To avoid crushing and related injuries:
NEVER work on, under or around a
load supported only by a hydraulic
jack. ALWAYS use a pair of adequately
rated jack stands.
ATD Tools Inc.
Printed in China
ATD7341-M0-0613
Page 2
SAFETY AND GENERAL INFORMATION
Save these instructions. For your safety, read, understand, and follow the information provided with and on this
device before using. The owner and/or operator shall have an understanding of the device, its operating characteristics
and safety operating instructions before operating the equipment. The owner and/or operator shall be aware that use
and repair of this product may require special skills and knowledge. Instructions and safety information shall be read
to and discussed with the operator in the operator's native language, making sure that the operator comprehends
their contents, before use of this equipment is authorized. If any doubt exists as to the safe and proper use of this
device, remove from service immediately.
Inspect before each use. Do not use if abnormal conditions such as cracked welds, damaged, loose or missing
parts are noted. Any equipment that appears damaged in any way, is found to be worn, or operates abnormally shall
be removed from service until repaired. If the equipment has been or is suspected to have been subjected to an
abnormal load or shock, immediately discontinue use until inspected by a factory authorized repair facility (contact
distributor or manufacturer for list of authorized repair facilities). It is recommended that an annual inspection be
made by an authorized repair facility. Labels and Operator's Manuals are available from the manufacturer.
PRODUCT DESCRIPTION
This Hydraulic Service Jack is designed to lift, but not support, one end of a vehicle. Immediately after lifting, loads
must be supported by a pair of appropriately rated jack stands. This Swift Lift service jack has a unique feature that
provides fast, no load lifts to the jacking point, at which time it lifts in approximately 1/4"~3/4" increments.
Never use a hydraulic jack as a stand alone support device. After lifting, immediately support the lifted
vehicle with appropriately rated jack stands. Never place any portion of your body under the vehicle when
!
lifting or lowering.
PREPARATION
Assembly
Insert handle into the handle fork. Tighten the bolt on handle fork to prevent accidental removal of handle while in
use.
Before Use
1.
Verify that the product and application are compatible
2. Before using this product, read the operator's manual completely and familiarize yourself thoroughly with the
product, its components and recognize the hazards associated with its use.
3. To familiarize yourself with basic operation, locate and turn the release valve (handle):
a. Clockwise until rm resistance is felt to further turning. This is the ‘CLOSED’ release valve position used to
raise the saddle.
b. Counter-clockwise, but no more than 1/2 turn from the closed position. This is the ‘OPEN’ release valve
position used to lower the saddle.
4. With Ram Plunger fully retracted and release valve closed, pump the operating handle. If Ram Plunger responds
immediately, jack is ready for use. If jack does not respond, follow Bleeding/Venting Trapped Air instruction below.
5. Ensure that jack rolls freely. Raise and lower the unloaded saddle throughout the lifting range before putting into
service to ensure the pump operates smoothly. Replace worn or damaged parts and assemblies with authorized
replacement parts only.
Bleeding/Venting Trapped Air
With the release valve in the OPEN position (step 3b. above) and with saddle fully lowered, locate and remove the
cover plate, then remove the oil ller plug. Insert handle into handle fork and pump 6 to 8 full strokes. This will help
release pressurized air which may be trapped within the reservoir. Reinstall the oil ller plug and check operation.
.
2
Page 3
SPECIFICATIONS
Model Capacity Jack Size (L x W x H) Min. Height Max. Height Saddle Dia.
ATD7341 3-1/2 Ton 28-1/2" x 13-3/4" x 6-1/2" 5-1/2" 22" 4"
OPERATION
Lifting
Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the
!
vehicle as specied by the vehicle manufacturer.
1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock
each unlifted wheel in both directions to prevent inadvertent vehicle movement.
2.
Close the release valve by turning the handle clockwise until rm resistance is felt.
3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack
saddle under lift point.
4. Verify lift point, pump handle to contact lift point. To lift, pump handle until load reaches desired height.
5. Transfer the load immediately to appropriately rated jack stands.
NEVER use hydraulic jack as a stand alone
!
pair of appropriately rated jack stands. Use one pair of jack stands per vehicle. Rated capacity is per pair
only! Do not exceed rated capacity.
Lowering
Be sure all tools and personnel are clear before
you turn the handle counter-clockwise, the faster the load will come down. Maintain control of the rate of
!
speed at which the load lowers at all times!
1. Raise load high enough to clear the jack stands.
2.
Remove jack stands carefully.
3. Slowly turn the handle counter-clockwise, but no more than 1/2 full turn. If the load fails to lower:
a. Use another jack to raise the vehicle high enough to reinstall jack stands.
b. Remove the malfunctioning jack and then the jack stands.
c.
Use the functioning jack to lower the
4. After removing jack from under the vehicle, fully lower the saddle to reduce ram exposure to rust and contamination.
vehicle.
device! ALWAYS transfer the lifted load
lowering load. Slowly open the release valve! The more
IMMEDIATELY to a
Oil Filler Plug
(refer to parts list for location)
Front Wheel
Handle
(release valve)
Saddle
Lifting Arm
Foam Handle Pad
Handle Fork
Caster
Figure 1 - Typical Jack Nomenclature
3
Page 4
! WARNING
• Study, understand, and follow all instructions
before operating this device.
• Do not exceed rated capacity.
! WARNING
X
• Use only on hard, level surface.
• This is a lifting device only. Immediately after
lifting, support the load with appropriate means.
• Lift only on areas of the vehicle as specied by
the vehicle manufacturer.
• No alterations shall be made to this product.
• Only attachments and/or adapters supplied by
the manufacturer shall be used.
• Failure to heed these markings may result in
personal injury and/or property damage.
To avoid crushing and related injuries:
•
Never work on, under or around a load supported
only by hydraulic jack.
• Chock unlifted tires in both directions.
• Do not use this device to lift, level, lower, support nor
move a house, mobile home, travel trailer, camper or
any building structure.
• Be alert and sober when using this product. Do not
operate under the inuence of drugs or alcohol.
MAINTENANCE
NOTE: Use only good grade hydraulic jack oil. Avoid mixing different types of uid and NEVER use brake uid,
turbine oil, transmission uid, motor oil or glycerin. Improper uid can cause premature failure of the jack and the
potential for sudden and immediate loss of load. We recommend premium hydraulic jack oil.
Adding oil
1. With saddle fully lowered set jack in its upright, level position. Remove oil ller plug.
2. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall oil ller plug.
Changing oil
For best performance and longest life, replace the complete uid supply at least once per year.
1. With saddle fully lowered, remove oil ller plug.
2. Lay the jack on its side and drain the uid into a suitable container.
Note. Dispose of hydraulic uid in accordance with local regulations.
3. Fill with oil until ~3/16" above the inner cylinder as seen from the oil ller hole. Reinstall oil ller plug.
Lubrication
A periodic coating of light lubricating oil to pivot points, axles and hinges will help to prevent rust and assure that
wheels, casters and pump assemblies move freely.
Cleaning
Periodically check the pump piston and ram for signs of rust or corrosion. Clean as needed and wipe with an oily
cloth.
Note: Never use sandpaper or abrasive material on these surfaces!
Storage
When not in use, store the jack with saddle fully lowered.
4
Page 5
TROUBLESHOOTING
Symptom Possible Causes Corrective Action
Jack will not lift load
Jack will lift, but not maintain
pressure
Jack will not lower after unloading • Reservoir overlled
Poor lift performance • Fluid level low
Will not lift to full extension • Fluid level low • Ensure proper uid level
• Release valve not tightly closed
• Load is too heavy
• Release valve not tightly closed
• Hydraulic unit malfunction
• Linkages binding
• Fluid level low
• Hydraulic unit malfunction
• Ensure release valve tightly closed
• Consider higher capacity jack
• Ensure release valve tightly closed
• Discontinue use, contact Technical
Service
• Drain uid to proper level
• Clean and lubricate moving parts
• Ensure proper uid level
• Ensure proper uid level
• Discontinue use, contact Technical
Service
REPLACEMENT PARTS
Not all components of the jack are replacement items, but are illustrated as a convenient reference of location and
position in the assembly sequence. When ordering parts, give Model number, serial number and parts description
below. Call or write for current pricing: ATD Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385.
Tel:(816)891-6390 Fax:(816)891-6599
5
Page 6
Replacement Parts for Model ATD7341:
Item Part No. Description Qty
1 G73500-0002 Hydraulic Power Unit 1
2 G73500-0018 Front Wheel Assembly 2
3 G72500-0003 Rear Caster Assembly 2
4 G49300-0006 Saddle 1
5 G73800-0008 Saddle Pad 1
6 F36100-0001 Oil Filler Plug 1
7 G73500-0007 U-joint Assembly 1
8 G73500-0026 Handle Assembly 1
9 G61801-1007 Foam Handle Pad 1
10 G48900-0024 Handle Retaining Bolt, M10 1
11 G73500-0010 Return Spring (Right), Handle Fork 1
12 G73500-0016 Return Spring (Left), Handle Fork 1
13 G49300-0002 Return Spring, Lift Arm 1
14 G73700-0002 Tool Tray 1
15 G73500-0005 Pump Piston 1
16 G73500-0021 Handle Fork 1
- G73504-0000 Repair Kit -
** Replacement requires special skills,
knowledge, and equipment. Only
authorized service center may perform
the repair and/or replacement of these
items.
11
16
12
10
5
4
13
14
1
6
7
15
8
3
9
Figure 2 - Replacement Parts Illustration for Model ATD7341
3
2
65
Page 7
ONE YEAR LIMITED WARRANTY
For a period of one (1) year from date of purchase, ATD Tools Inc. will repair or replace, at its option, without
charge, any of its products which fails due to a defect in material or workmanship under normal usage. This limited
warranty is a consumer's exclusive remedy.
Performance of any obligation under this warranty may be obtained by returning the warranted product, freight
prepaid, to ATD Tools Inc. Warranty Service Department, 160 Enterprise Drive, Wentzville, MO 63385, U.S.A.
Except where such limitations and exclusions are specically prohibited by applicable law, (1) THE
CONSUMER'S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE
PRODUCTS AS DESCRIBED ABOVE. (2) ATD Tools Inc. SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER. (3) ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO ONE YEAR, OTHERWISE THE REPAIR, REPLACEMENT OR REFUND AS
PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER,
AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. (4) ANY MODIFICATION,
ALTERATION, ABUSE, UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND
IS NOT COVERED BY THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not
apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specic legal rights, and you may also
have other rights, which vary from state to state.
ATD Tools Inc.
160 Enterprise Drive, Wentzville, MO 63385
7
Page 8
Note Page
ATD Tools Inc.
160 Enterprise Drive, Wentzville, MO 63385
8
Loading...