ATD Tools ATD-6810 user manual

ATD-6810

SPRAY GUN W/CUP

INSTRUCTION MANUAL

Read this Instruction Manual carefully and understand it completely, basic precaution
should be strictly followed to prevent the damage to the tool and injury to the operator.
Retain this manual for further reference. And you should pay more attention to the
Technical Data.

Description

A High pressure spray gun is ideal for refinishing a classic car or a wide variety of home improvement
projects. This high pressure paint s prayer features air, fluid and fan controls to offer a wide variety of patterns.
It is supplied with a 1000 cc suction feed aluminum cup.

Technical Data

Type of Feed : Suctio n
Air Inlet: 1/4”

Standard Diameter of Nozzle: φ2.0mm

Optional Diameter of Nozzle: φ1.5~2.5mm
Recommended air pressure: 3.0~ 4.0 bar (45-60psi)

Max. Pressure of air: 8.3 bar (120psi)
Paint Capacity: 1000cc
Avg. Air Consumption: 170-250l/min (6.0-8.8cfm)
Pattern Width: 180-230mm (7.1-9.1”)
Weight: 1.1kgs (2.42lbs)
A-weighted sound pressure leve l: 77.1dB(A)
Sound power level: 88.1dB(A)

Important Safety Instructions

1. For toxic vapors produced by spraying certain materials can create intoxication
and serious damage to health. Always wear safety glasses, gloves and
respirator to prevent the toxic vapor ha zard, solven t and pointing paint co ming
into contact with your eyes or skin.

2. Never use oxygen, combustible or any other bottle gas as a power source or
would cause explosion and serious personal i nj ur y.

3. Fluid and solvent can be highly flammable or combustible. Please Use the tool
only in well-ventilated area, and avoid any ignition sources, such as smoking,
open flames and decrial hazard.

4. Disconnect paint gun from air supply hose before doing tool maintenance and
during non-operation, for emergency stop and prevention of unintended
operation, a ball valve near the gun to air supply is recommend.

5. Use clean, dry and regulate compressed air rated at 3.0~4.0bar, never exceed
maximum permissive operating pressure 8.3 bar(120psi).

6. Never use homogenate hydrocarbon solvent, which can chemically react with
aluminum and zinc parts and chemically compatible with aluminum and zinc
parts.

7. Never point gun at yourself or others at any time.

8. Before operating the paint gun, ensure all the sc rews & caps are securely tightened to prevent leaking.

9. Before painting, make inspection for free movement of trigger and nozzle to insure tool can operate well.

10. Never modify this paint gun for a ny appli cati ons. O nly use p arts, nozzles and accessories recommended
by the manufacturer.

Instructions for Operation

Preparation

1. After unpacking the paint gun, inspect carefully for any damage that may have occurred during transit.

Make sure to tighten fittings, bolts, etc., before putting unit into service.

2. Thoroughly mix and thin paint in accordance with the paint manufacturer’s instructions. Most materials

will spray readily if thinned properl y.

3. Strain material through filter, cheese cloth or a paint strainer.

4. Fill the canister about ¾ full and start the air compressor.

WARNING Do not exceed Maximum Pressure of S pra y Gun or any other parts in the compressor system.

5. After connecting the gun to the air supply, please make sure that the fluid cap, container and air hose

have been connected tightly to the spray gun.

6. Set up a piece of cardboard or other scrap material to use as a target and adjust for best spray pattern.

WARNING Never aim or spray at yourself or anybody else as it could cause serious injury.

7. Test the consistency of the material by making a few strokes on a cardboard target. If material still

appears too thick, add a small amount of thinner. THIN WITH CARE! Do not exceed paint
manufacturer’s thinning recommendations.