ATD Tools ATD-10538 User Manual

ATD-10538

3/8” Electric Drill

Tool specifications:

Rated Voltage: (V) 120
Rated Frequency: (Hz) 60
Rated current: (A) 3.3
No-load Speed: (RPM) 0-2700
Speed Selection: Yes
Right/Left Rotation: Yes
Chuck Size: 3/8” (10 mm)
Drilling Capacity (max):

- Steel: 3/8” (10 mm)

- Wood: 3/4” (20 mm)
Net Weight: 3 lbs (1.4kg)

WARNING – To reduce the risk of injury, please read this instruction manual before use.

Intended use

The ATD10538 drill is intended for impact drilling in brick, concrete as well as for
drilling in wood, metal, ceramic and plastic.

Electrical safety

The electric motor has been designed for 120V only. Always check that the power
supply corresponds to the voltage on the rating plate.

Double insulation

This tool is double insulated in accordance with EN60745; therefore no earth
(ground) wire is required.

General safety rules for work with electric tools

Read and understand all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious personal injury. The term

“power tool” in the warnings listed below refers to your electrically operated (corded)

power tool or battery operated (cordless) power tool.

Safety warning and precautions

Save this manual. You will need the manual for the safety warning and

precautions, assembly instructions, operating and maintenance procedures, parts

list and diagram. Read these instructions before operating this product. Save this

instruction and follow them to reduce the risk of fire, and personal injury.

1. Work area.
a) Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical safety.
a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your

body is grounded.

c) Don’t expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord to carry the tools or pull the

plug from an outlet. Keep cord away from heat, oil, sharp edges or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk
of electric shock.

e) When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These cords are rated for outdoor use and reduce the

risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual

current device (RCD) protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety.
a) Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use tool while tired or under the influence of
drugs, alcohol, or medication. A moment of inattention while operating power

tools may result in serious personal injury.

b) Use safety equipment. Always wear eye protection. Safety equipment such

as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Be sure switch is off before plugging in. Carrying

tools with your finger on the switch or plugging in tools that have the switch on
invites accidents.

d) Remove adjusting keys or wrenches before turning the tool on. A wrench or

a key that is left attached to a rotating part of the tool may result in personal
injury.

e) Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used. Use of dust

collection can reduce dust-related hazards.