Page 1
VF-AT-NBC
IMPORTANT:
The “User Operating
Card” must be left with
Visidec Focus Articulated
Arm once installed.
Component Checklist
Installation Instructions
Focus | Notebook/Monitor Arm Combo
Bits Box
Notebook Tray and
Arm Assembly
Pole Assembly
Pole Base
Pole Top Cap
Arm Assembly
M8 x 30mm
Screw
Cable Clip
TOOLS REQUIRED:
Power Drill
9mm (0.35”) Drill Bit
Phillips Head
Screwdriver
Primary Arm Cable
Steel Washer
Cover (x2)
Cable Ball
Desk Clamp Box
5mm Allen Key
Secondary Arm Cable
Cover (x2)
Hook and Loop
Fasteners (x4 sets)
Pressure Plate
M8 Desk Clamp Screw
IMPORTANT INFORMATION:
! IMPORTANT - Install Notebook/Monitor Arm Combo as per Installation Instructions.
! This product supports a maximum load of 8kg (17.5lbs) in each arm.
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
! The manufacturer accepts no responsibility for incorrect installation.
Step 1. Check Components
Check you have received all parts against the Component Checklist and Hardware above.
Step 2. Mount Visidec Pole to desk: Bolt Through or Desk Clamp
M4x10mm (x4)
M4x12mm (x4)
M4x16mm (x4)
Display Mounting
Screws
Desk Clamp Bracket
Bolt Through
Drill 9mm (0.35") hole in the Work
Surface at the desired position and
assemble as shown below.
Pole Assembly
Steel Washer
M8 Desk
Clamp Screw
5mm Allen Key
Note: It is recommended that the Pole
Assembly be mounted towards the rear
edge of the Work Surface.
Pole Base
9mm (0.35")
Hole
TIGHTEN
OR
A. Attach the Desk
Clamp Bracket to the bottom
of the Pole Assembly using the
M8x30mm Screw. Tighten
firmly using the 5mm Allen
Key. Ensure the Visidec logo is
facing the front as shown.
Desk Clamp
Bracket
M8x30mm
Screw
Pole Base
Pole Assembly
B. Install the M8
Desk Clamp Screw and
Pressure Plate as shown.
Pressure Plate
M8 Desk
Clamp Screw
5mm Allen Key
Step 3. Attach the Notebook Tray Arm to Pole Assembly
A. Unlock the First Handgrip.
Remove from the Pole Assembly.
First
Handgrip
Second
Handgrip
REMOVE
UNLOCK
Second
Handgrip
B.
Unlock the Second
Second Handgrip Tab
Second Handgrip
SLIDE
C. Slide Second
Handgrip to the top of
UNLOCK
the Visidec Pole so the
Second Handgrip Tab
protrudes.
Handgrip.
D. Slip the Notebook Tray Arm
over the Handgrip Tab and then
onto the Visidec Pole.
Desk Clamp
C. Adjust the height of the Pressure Plate to suit the
Work Surface and Tighten Firmly in the desired location.
ADJUSTMENT RANGE
Note: It is recommended
that the Pole Assembly be
clamped to the rear or
side edge of the Work
Surface.
Notebook
SLIP
Tray Arm
Suits 12mm
to 38mm
thick Work
(0.5”)
(1.5”)
Surfaces
TIGHTEN
E. Slide the Notebook Tray Arm
and the Handgrip down the Visidec
Pole.
F. Lock the Handgrip.
Note: DO NOT
OVER TIGHTEN
LOCK
Pole Assembly
Work Surface
5mm Allen Key
SLIDE
Page 2
TFIL
Step 4. Install the Notebook
A. Adjust the Support Tabs to suit the width of
your Notebook Computer.
Step 5. Attach the Monitor Arm to Pole Assembly
A. Insert First Handgrip back
onto the Pole
so that the Tab
protrudes.
Tab
B. Slip the Arm
over the
then onto the Pole.
Assembly
Handgrip Tab and
C. Lock the Handgrip at
desired height.
Note: DO NOT
OVER TIGHTEN
NOTE: Ensure that the Support Tabs do not
obstruct
any cable ports.
B. To increase stability, use the self
adhesive Hook-and-Loop
Fasteners
Step 6. Fasten Display to Monitor Arm
supplied:
•
Peel off the backing paper
from the fasteners.
•
Attach fasteners to your
Notebook Computer and
the Notebook Tray.
•
Ensure that each set of
fasteners are correctly
aligned,
i.e. Hook to Loop.
Step 8. Cable Management -
Ensure arms are fully extended before attaching cables.
A. Route the Cables underneath the Arms, inserting the Primary
and Secondary Arm Cable Covers to hold the Cables in place.
TIP: Leave enough slack in the cables
at the joints
to allow full movement.
First Handgrip
M4 Display
Mounting Screws
For displays with 75mm x 75mm
mounting hole patterns
To Insert Cable Covers
Arm
Assembly
C.
Insert tabs
OR
D. Insert the Top
Cap and Allen Key
into the Pole.
Pull-out
tabs
For displays with 100mm x 100mm
mounting hole patterns
F. Route the Notebook Cables
through the Cable Management
Clip on
the back of the Notebook
Tray.
Secondary Arm
Cable Cover
B. Insert cable into slots using
cable balls to hold them in place.
D.
Push-in
E.
Then Push-up
Secondary Arm
Cable Cover
Primary Arm
Cable Cover
Primary Arm
Cable Cover
Step 9. Display Alignment
Set the height and position of the Notebook Tray and Monitor as desired.
The height can be adjusted by unlocking the Handgrips (see Steps 3, E and F).
For the optimal position of your display, refer to the Ergonomic Guidelines in your ‘User Operating Card’.
±5° Horizontal
Adjustment
95° Portrait/
Landscape Rotation
NOTE: If this product is in
Multi-user environment, use
the supplied Cable Clip to
secure the
cables to the pole.
Adjust the tilt angle of the Notebook Tray
as desired, locking it in position using
the 5mm Allen Key supplied.
25° TILT
TIGHTEN
LOOSEN
a
Installation Complete
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 06.09.12 ©
Loading...