Page 1
IMPORTANT:
The “User Operating
Card” must be left with
Visidec Focus Articulated
Arm once installed
VF-aT /
Installation Instructions
A Component Checklist - Check you have received all parts against the component checklist prior to installing
Desk Clamp Box
Arm Assembly
Pole Assembly
Top
User Operating Card
(see note at top of page)
B1
Bolt Through
Drill a 9mm (³/8”) hole in the Work
Surface at the desired position and
assemble as shown below.
Pole Assembly
Bolt Through Base
9mm (³/8”) Hole
Steel Washer
Bottom
Bits Box
Bottom
Primary Arm
Cable Cover
Secondary Arm
Cable Cover
OR
Desk Clamp Bracket
M8x30mm
Pole Top
Cap
Bolt Through
Base
B2
Desk Clamp
Step 1: Attach the Desk Clamp Bracket
to the bottom of the Pole Assembly using
the M8x30mm Screw. Tighten firmly
using the 5mm Allen Key. Ensure the
Visidec logo is facing the front as shown.
Desk
Clamp
Bracket
M8x30mm
Screw
Bolt Thru
Base
Pole
Assembly
Screw
Cable
Balls (x2)
Steel
Washer
5mm
Allen Key
Bottom
Pressure Plate
Display Mounting
Cable Clip
5mm Allen
Key
Step 2: Install the M8 Desk Clamp
Screw and Pressure Plate as shown.
Pressure
Plate
M8 Desk
Clamp Screw
M8 Desk
Clamp Screw
Screws
M4x10mm
(x4)
M4x12mm
(x4)
M4x16mm
(x4)
Allen Key
5mm
M8 Desk Clamp Screw
(found in the Desk
Clamp Box)
NOTE: It is recomended
that the Pole Assembly be
mounted towards the rear
edge of the Work Surface
5mm Allen Key
Tighten Firmly
Step 3: Adjust the height of the Pressure Plate to suit the
Work Surface and Tighten Firmly in the desired location.
ADJUSTMENT RANGE
Suits 12mm (½”)
to 38mm (1½”)
Thick Work
Surfaces
NOTE: It is recommended that the Pole
Assembly be clamped to the rear or side
edge of the Work Surface
5mm Allen Key
Tighten Firmly
Pole
Assembly
Work Surface
Page 2
C Assemble the Arm Assembly onto the Pole Assembly
Handgrip Tab
Handgrip
Step 2:
Lift the handgrip to
Step 1:
Unlock the
handgrip
Step 4:
Slide the Arm
Assembly and
the Handgrip
down the
Pole
the top of the pole
so that the Handgrip
Tab protrudes
Pole Top Cap
Step 6:
Insert the Pole
Top Cap into
the top of the
Pole
Arm Assembly
Step 3:
Slip the Arm Assembly over the
Handgrip Tab and then onto
the Pole
Step 7:
Insert the 5mm
Allen Key into
the slot in
the Pole
Top Cap
D Mount the Display
M4 Display Mounting Screws
For Displays with 75mm x 75mm
(3” x 3”) mounting hole patterns
Step 5:
Lock the
Handgrip
Note: DO NOT
OVER TIGHTEN
E Cable Management - Ensure arm is fully extended before connecting cables
Step 2: Insert
Secondary Arm
Cable Cover*
Step 1: Connect cables
NOTE: Leave enough slack in the
cables to allow for movement
Step 3: Insert
Primary Arm
Cable Cover*
Step 4: Insert cables into
slot, using cable balls to hold
them in place
(single user only)
*To insert Cable Covers:
Insert tabs
Push in...
NOTE: If Visidec Focus
M4 Display Mounting Screws
For Displays with 100mm x 100mm
(4” x 4”) mounting hole patterns
Cable
Clip
Articulated Arm is to be used
in a multi-user environment,
use the supplied cable clip
to secure the display ’s
cables to the pole.
Cable
Balls (x2)
F Leave the “User Operating Card” with Visidec Focus Articulated Arm
Leave the “User Operating Card” secured to the Visidec Focus Articulated Arm for the user’s reference.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 06.09.12 ©
...and then up
Loading...